Download
Share
Print this page
  1. Manuals
  2. Brands
  3. QTS Manuals
  4. 3D Printers
  5. F300
  6. Manual

QTS F300 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Thank you for purchasing F300 3D PRINTER .
User experience is us concerned about.
Overall structure is new created with
more friendly operation interface.
We hope F300 will become your best partner in
work. And help your creative idea to become real.
Next, follow the manual with carefulness to
assemble whole printer. Step by step,
we will assist you to correctly install. Enjoy!

Advertisement

loading

Summary of Contents for QTS F300

  • Page 1 User experience is us concerned about. Overall structure is new created with more friendly operation interface. We hope F300 will become your best partner in work. And help your creative idea to become real. Next, follow the manual with carefulness to assemble whole printer.

  • Page 2: Table Of Contents

    Parts List: Long pillar（X、Y、Z）X3 Rubber padX4 Panel screw(M4)X4 Frame screw(M6)X36 Carbon rod x6 2040 al. pillarX8 2040 al. pillarX1 Main Plate(set) Hot bed (set) Glass stage Print head (set) Filament Holder (set) Extrusion motor (set) Touch panel (set) Tools: 5mm Hex T-Wrench 3mm Hex L- Wrench 2.5mm Hex L- Wrech Cross screwdriver...
  • Page 4 Tips: Put the pillar on table edge. It is more easily for you to assemble the 2040 al. pillar. Frame assemble Long pillar- Z (4 holes side) 1.Put the carton pad on workplace to avoid the parts damage your furniture. 2.
  • Page 5 Frame assemble Frame assemble Long pillar Z (8 holes side) 1. Install 3 of 2040 al.pillars and the 2040 al.pillar (with switch) on top of the Z pillar. Notice the relatively relationship between them as drawing.
  • Page 6 Frame assemble Long pillar X, Y 1. I n s t a l l t h e X p i l l a r w i t h 4 o f M 6 s c r e w s o n t o p fi r s t a n d t h e n 2 o f M 6 s c r e w s b e n e a t h 2.
  • Page 7 Frame assemble 2040 al. pillars 1. Install the 2 of 2040 al. pillars on top of frame with 8 of M6 screws. Beware the trough side facing outward. 2. Install the last 2040 al. pillar under the frame. Beware the trough side facing outward.

  • Page 8: Rubber Padx4

    Rubber pads 1. As drawing, install the 4 rubber pads. 2. Notice that when locking screws, the T-nuts should vertical to the 2040 al.pillar. If no, loose the screw and drive again.

  • Page 9: Main Plate(Set)

    Main plate 1. Put the main plate on the fame with main board side toward bottom, and the opening side toward the 2040 al. pillars. 2. Loose the T-nut and drive to right direction and then tightly fasten it. 3. Lay down the machine, and then turn it upside down to right show.
  • Page 10 Power wires 1. Find out the E,N,L 3 tag wires on the 2040 al. pillar (with switch). Connect it to the power terminal with corresponding position by using the cross screwdriver as drawing. 2. Check the position again and firmly locked. Ｎ...
  • Page 12 Signal wires 1. Connect the wires of the motor as drawing.。 2. Connect the wires of limit sensor to main board. X-MOTOR Z-MOTOR Y-MOTOR...
  • Page 14 Push out the F l i p t h e L C D both black side c a b l e a n d lightly i n s e r t i t Touch panel 1. Move up the machine a little to let panel cable and the cable of SD card extension go through the opening space of the main plate.
  • Page 15 Push back the both black side indeed 扣下方 The most left pin of the SD card slot should be map to the most up pin of the terminal.
  • Page 16 4. After install LCD holder on the 2040 al. pillar, then put on the cover Tips: Locate 4 screws first and then fasten them.
  • Page 17 E x t r u d e r 1. Rotate the machine 90 degrees as the drawing. Install extruder motor on the middle of 2040 al. pillar with hex L- Wrench by ball side. Notice. Carefully holding the extruder motor due to its heavy weight in order to avoid damage.
  • Page 18 Filament holder 1. Install filament holder on the top of Z pillar. 4 T-nuts have to be locked. 2. Replace the machine with the operation side toward self.
  • Page 19 Carbon rods 1. Take out the 6 carbon rods from the package. And wipe a slight oil form accessory. (Notice: Just a few oil, not too much. It is to prevent cause friction sound) 2. Connect separate rod to magnetic ball on the slide stage on each long pillar.
  • Page 20 4. Connect the 4x2 Teflon tube to couplers on Extruder.
  • Page 21 trunking trunking Wiring 1. Pass the cable of the print head through the B trunking of the Y pillar, and go through the reserved space to the electric control box. Tips:...
  • Page 22 2. Connect the two red wires to corresponding position as drawing and fasten the screws 3. Connect the cable of the print head with the short cable which connected to the mainboard...
  • Page 23 4. Pass the cable of the extruder through the A trunking of the Y pillar, and go through the reserved space to the electric control box...
  • Page 24 5. Connect the E cable to corresponding terminal which tag “E-MOTOR”.

  • Page 25: Hot Bed (Set)

    Hot bed 1. Put the hot bed right form the printer with the insulation cotton pwards. Insert the 2 separate white wires into the corresponding connector (red) and lock screws. Pull the wires to be sure them was firmly locked. 2.
  • Page 26 3. Put the hot bed inside the frame over the main board. 4. Rotate the 6 T-nuts to lock direction separately with the hex wrench and then fasten them. (Be careful to connect cable avoid poor contact )

  • Page 27: Glass Stage

    Glass stage 1. Push the print head the most top. 2. Take out the glass stage from the C box. Put 1 buffer strip side toward the Z pillar. Tilt the stage 45 degrees up and lay it down slightly. 3.
  • Page 29 Congratulations! Just finish good job! Next, please follow our test instrument. Make sure that all function is correctly operated, and start your first print.
  • Page 30 E l e c t r i c t e s t Start Connect the power supply and click on the power switch.
  • Page 31 E l e c t r i c t e st Motor test Enter [Tools]→[Move]. Press the home button. The X, Y, Z axis will move to top and stop by the limit switch. If the error occurs, please check the wire connection. Setting Print Tools...
  • Page 32 E l e c t r i c t e s t Extruder test Back to the previous page, and enter [control]. Press the button, and check if the extruder gear operation correctly. Hot-End, Hot-Bed, Fan Test Stay in the control page. Press the icon will enable the corresponding function, and disable the function by press it again.
  • Page 33 E l e c t r i c t e s t Tools Control Extruder Move Control Auto level Z axis Control Control Hot End Hot Bed Target Emergency Stop Tools Auto level Move Control Z axis...
  • Page 34 Auto level Install ALD(Auto level detector) Insert the ALD into the port on the print head surely.
  • Page 35 Auto Level Execute Auto Level Enter [Tools]→Press [Auto level] will start the procedure If pop up the window of “Please plug ALD＂ after press the [Auto level] button, it is means ALD not plugged correctly please plug again. Tool Setting Move Control Z Axis...

  • Page 36: Print Head (Set)

    Z Axis Starting layer height Enter [Tools]→[Manual] 1. Press the home button first. 2. Press the↓button to lower print head When approaching to the plate, the small scale will make the position more accurate. If the print head over hit the plate, it may cause the belt tooth jump or make the step motor go wrong step.
  • Page 37 Z Axis When the print head approach to the plate, select [0.01mm] scale and keep go in down until here the sound of the nozzle hit the glass. (back and forth make sure) After hear the sound, select [0.1mm] scale and press Z+ a step. Then press [SETZ=0] button, the starting layer height is set up.
  • Page 38 Prepare For Printing Glue a thin layer on the glass plate. 。 Heating the nozzle until 190 degree Control Tools Control Move Z Axis Auto Level...
  • Page 39 Prepare For Printing Put the filament on the spool holder. Draw a strip put in the extruder and make the gear bite the strip. Press [↓] until the material go into the 4x2 teflon tube.. Draw a strip put in the extruder and make the gear bite the strip.
  • Page 40 Prepare For Printing After confirm the filament in the teflon tube, push the stopper and the moving part of the extruder at the same time until the bolt plug in the hole. And hen push the filament easily until the material melt from the nozzle. Beware to push the moving part of the extruder after loading the filament, the bolt will pop up.
  • Page 41 Test printing Test printing Insert the SD card. Back to the main screen. Press [printing] and select the [wire_holder.gcode] file name. The machine is starting the printing process. Setting Print Tools SD Card...
  • Page 42 Test printing The [wire_holder] is to buckle on the 2040 al. pillar on top to fix the extruder wire and the print head cable. 。...
  • Page 43 Hot end Removal Wire Removal 1. Heat the hot end until the material melt from the nozzle and then pull out from the extruder. 2. Disable the heater and wait until the nozzle cool down. Remove the red wire and the white wire connector...
  • Page 44 Hot end Removal Hot end Removal 1. Loose the screw as the drawing, and then pull out the hot end. 2. We can release the force screw to let the heater and the thermistor go out. Attention! When install the thermistor, we should put it inside the middle of the small hole.
  • Page 45 S D Card File Software 1. Two kinds of slicer software CURA and KISSLICER are included. 2. Refer to the documentation for installation instructions and associated profiles. Digital Accessories 1. Wire_holder.gcode 2. 2020_cover.gcode 3. Platestop.gcode...