Samsung PN42C450 Quick Setup Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure you distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
Screws (M4 X L12)
Guide Stand
1
Stand
Connect the Guide Stand to the
Stand using four screws (M4 X L12)
as shown.
Rear
2 3
With your TV upright, connect the Fasten screws (M4 X L12) at
TV to the Stand as shown. position 1, and then fasten the
two screws (M4 X L12) at position
2.
Front
2
Rear
1
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
(Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
or • Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using
HDMI for the highest picture quality.
✎
When connecting to AV IN on the back of your TV, attach the video cable (yellow) to the green jack
next to the AV IN label. The jack will not match the color of the video cable (yellow).
Video Cable
(Not Supplied)
Top view
Front
Lowest Quality Connection
Audio/Video connection (480i only)
Rear
Using an Audio/Video Cable
Audio Cable
Digital Audio System, Amplifier, Home Theater (Not Supplied)
Device
VIDEO OUT AUDIO OUT
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the MENU button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control,
Select Language of the OSD.
select the language for the On
Screen Display (OSD), and then
Language
press ENTERE button.
2
Select Home Use, and then
press ENTERE button. If you
Select 'Home Use' when installing this TV in your home.
select Store Demo, the TV will
reset your picture and audio
Store Demo
settings every 30 minutes.
3
Antenna Source is Air, Cable
or Auto, you must select Select the Antenna source to memorize.
Antenna Source to same type
Air
as your cable system type. After
Cable
selecting source, select Start;
Auto
then press the ENTERE
button on your remote.
Best Connection
HD connection (up to 720p/1080i)
HDMI Cable (Not Supplied)
HDMI to DVI Cable
(Not Supplied)
Audio Cable (Not Supplied)
Good Connection
Component connection (up to 720p/1080i)
COMPONENT OUT
Component Cable
(Not Supplied)
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
POWER
The TV memorizes the available
channels. This process can take
P
Plug & Play up to 45 minutes.
English
:
Español
Français
U Move E Enter
5
After the TV has memorized
Plug & Play the channels, choose the
Clock Mode. Select Auto if
you have a digital channel in
your area. Select Manual if you
Home Use don't, or if you have a cable or
satellite box. When done, press
L Move E Enter
ENTERE button.
✎
If you select Manual, the clock
Plug & Play
setting screen appears.
6
Start
Select the daylight savings time
Start
setting: Off, On or Auto and
Start
then press ENTERE button.
✎
U Move E Enter m Skip
This function is only available
when the Clock Mode is set to
Auto.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Using an HDMI Cable
DVD / Blu-ray player / HD cable box /
HD STB (Set-Top-Box) satellite receiver
Device
HDMI OUT
Very Good Connection
HD connection (up to 720p/1080i)
Connecting a PC
Using a DVI to HDMI Cable
Connect your TV to a PC to use it as a Monitor.
DVI OUT DVD / Blu-ray player / HD cable box /
HD STB (Set-Top-Box) satellite receiver
AUDIO OUT Device Audio Cable (Not Supplied)
HDMI to DVI Cable (Not Supplied)
Using a Component Cable
Digital Audio System, Amplifier,
Home Theater
Device
AUDIO OUT
Audio Cable (Not Supplied)
7
Select the time zone in which you live, and then press ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
Plug & Play
The Enjoy your TV. screen appears. Then press ENTERE button.
Auto Program in Progress.
DTV Air : -- Air : --
If You Want to Rerun Plug & Play
DTV Cable : -- Cable : -- Cable : 35
1. Press the SOURCE
48%
2. Press the MENU
Stop
3. Press the ▲ or ▼ button to select Setup, and then press ENTERE button.
E Enter m Skip
4. Press ENTERE again to select Plug & Play.
Plug & Play
Set the Clock Mode.
Auto
Clock Mode
Manual
U Move E Enter m Skip
Plug & Play
Set to daylight saving time.
Off
On
DST
Auto
U Move E Enter m Skip
Analog Audio connection
Using an Audio Cable
Amplifier / DVD home theater
Audio Cable (Not Supplied)
AUDIO IN
Digital Audio connection
Using an Optical Cable
Digital Audio System
Optical Cable (Not Supplied)
OPTICAL
HD connection
Using a DVI to HDMI Cable
AUDIO OUT
DVI OUT
Using an D-Sub Cable
D-Sub Cable (Not Supplied)
PC OUT
AUDIO OUT
button on your remote, then select TV mode.
button on your remote to display the menu.
BN68-02609A-00