Samsung BN68-02664A-03 Quick Setup Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
STOP
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
Please do not return this unit. 85 Challenger Road Ridgefield Park, NJ 07660-2112
If you have problems operating your
Samsung Electronics Canada Inc.
TV, call:
1-800-SAMSUNG (1-800-726-7864) 55 Standish Court Mississauga, Ontario L5R 4B2
For web support please visit:
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
www.samsung.com/support
To register this product, visit : www.samsung.com/register.
Getting Started
Step 1 :
Install the Stand
Follow the steps below to connect the TV to the stand.
Make sure to distinguish between the front and back of the Stand and Guide
✎
Stand when assembling them.
Make sure that at least two people lift and move the LCD TV.
✎
Lay the product down, with the screen facing up and fasten the screws.
✎
1
2
Stand
Screw
Step 2 :
Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote upward
as shown in the figure to the right.
2. Install two AAA batteries.
Make sure to match the + and - ends of
✎
the batteries to the diagram in the battery
compartment.
3. Replace the cover.
Step 3 :
Connect Power and Antenna or Cable
Connect AnT In to:
• Wall cable jack or
or
• VHF/UHF
Antenna or
Power Input
• Cable or Satellite
box Ant or Cable
Use a 75 ohm (round) cable.
Out
Make sure the AC power cord
is plugged in securely to the
wall outlet and the TV.
Step 4 :
Connect External Devices
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
For the very best picture quality, select HD signal sources and use HDMI cables and
connections. Note that many digital cable programs are not in HD. Check with your video
provider to ensure your are receiving HD signals.
AV IN 2
Audio/Video connection (480i only)
Using an Audio/Video Cable
VCR
VIDEO OUT AUDIO OUT
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Lowest Quality Connection
Step 5 :
Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the EnTErE
To skip a screen, press the MEnU button.
To turn on your TV, press the button on the remote or press the
POwEr
POwEr button on the TV. To run Plug & Play, follow these steps:
Plug & Play
Select Language of the OSD.
English
Español
Language : English
Français
U Move E Enter
1. On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press EnTErE button. The
Home Use screen appears.
2. Select Home Use, and then press EnTErE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press EnTErE button, the Antenna Source screen appears.
3. If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press EnTErE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
AV IN 2 AV IN 2
HD connection (up to 1080p)
Using an HDMI Cable
HDMI OUT Device
DVD / Blu-Ray player / HD Cable Box /
The HDMI connection carries
HD Satellite receiver (STB)
AV IN 2 AV IN 2
digital video and audio.
Best Connection
HD connection (up to 1080p)
Using an DVI to HDMI Cable
DVI OUT
Device
AV IN 2
DVD / Blu-Ray player /
AUDIO OUT
Cable Box /
Satellite receiver (STB)
Very Good Connection
Component connection (up to 1080p)
Using a Component Cable
AUDIO OUT COMPONENT OUT
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Good Connection
✎ When connecting to AV In on the back of your TV, attach the video
cable (yellow) to the green jack next to the AV In 1 label. The jack will
not match the color of the video cable (yellow).
If your TV is attached to a cable system and you have no cable box, you
4.
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital. After you
have selected the cable system type, select Start, and then press the
EnTErE button on your remote.
button.
Most cable systems are Standard (STD) systems. If you are not
✎
sure about what kind of cable system you have, contact your cable
company.
5. The TV memorizes the available channels. This process can take up to
45 minutes. After the TV has memorized the channels, the Clock Mode
screen appears.
6. Choose the Clock Mode. Select Auto if you have a digital channel in
your area. Select Manual if you don't, or if you have a cable or satellite
box. When done, press EnTErE button. The Daylight Savings screen
appears.
If you select Manual, the clock setting screen appears.
✎
7. Select the Daylight Saving Time setting: Off, On, or Auto, and then
press EnTErE button.
8. After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the BLUE button to skip this section.
9. The Enjoy your TV screen appears. and then press
English - 1
Connecting an audio device
Connect your TV to your Home Theater or other audio
device to enjoy enhanced sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Device
Basic Functions
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.SIzE
you press it, your TV displays the current setting. Thereafter, each time you press the
P.SIzE button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen
EnTErE button.
Wide Fit 4:3 Standard screen
Screen Fit displays a full HD picture covering the entire screen with no cutoff on
✎
any side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p),
Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
AV IN 2 AV IN 2
Analog Audio connection
Using an Audio Cable
Device
AUDIO IN
Amplifier / DVD Home Theater
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
HD connection
Using an HDMI Cable
AUDIO OUT
DVI OUT
PC
Using an D-Sub Cable
PC OUT AUDIO OUT
PC
button on your remote. The first time
Zoom 1 Zoom 2
Screen Fit