Electrolux N7E Installation And Operating Manual page 23

E E . . 7 7 E E l l e e c c t t r r i i c c a a l l c c o o n n n n e e c c t t i i o o n n
E E . . 7 7 . . 1 1 E E l l e e c c t t r r i i c c a a l l a a p p p p l l i i a a n n c c e e s s
W W A A R R N N I I N N G G
Before connecting, make sure
the mains voltage and frequency
match those indicated on the
appliance dataplate.
• To access the terminal board, remove the control panel of
the appliance by removing the fixing screws.
• Connect the power cable to the terminal block according to
the wiring diagram provided with the appliance (refer to
B.3.3 N7E Electrical appliance Technical data ).
• Secure the power cable with the cable gland.
I I M M P P O O R R T T A A N N T T
The manufacturer declines any liability if
the safety regulations are not respected.
E.7.1.1Power cable
Unless otherwise specified, our appliances are not equipped
with a power cable. The installer must use a flexible cable
having characteristics not lower than the H07RN-F rubber
insulated type.
F F I I N N S S T T R R U U C C T T I I O O N N F F O O R R T T H H E E U U S S E E R R
F F . . 1 1 G G e e n n e e r r a a l l p p r r e e c c a a u u t t i i o o n n s s
• Before use, carefully clean any industrial greases from the
tank and baskets, proceeding as follows:
– fill the tank with water and normal detergent and bring to
boil for a few minutes.
– drain through the special tap after lifting the relative
safety protection, and carefully rinse the tank with clean
water.
• The appliance is intended for industrial use by trained
personnel.
• Do not use the appliance empty or in conditions that
compromise its optimum efficiency. Also, if possible, pre-
heat the appliance immediately before use.
• This appliance must only be used for its expressly designed
purpose; i.e. for frying foods in oil or solid fat. Any other use
is to be considered improper.
• Before introducing oil in the tank, make sure it does not
contain water.
• Pour the oil in the tank up to the maximum level indicated by
the special reference notch obtained on the rear wall of the
tank.
1 2
Protect the section of cable outside the appliance with a metal
or rigid plastic tube.
E.7.1.2Circuit breaker
Verify that a safety circuit breaker is installed between the
power cable of the appliance and the mains electric line. The
contact opening maximum distance and leakage current must
comply with the local safety regulations.
E.7.1.3Equipotential node and Earth
connection
Connect the appliance to an earth; it must be included in an
equipotential node by means of the screw located at the front
right under the frame. The screw is marked with the symbol
E E . . 8 8 S S a a f f e e t t y y t t h h e e r r m m o o s s t t a a t t
Some of our appliance models use a safety thermostat that
cuts in automatically when temperatures exceed a set value,
shutting off the gas supply (gas appliances) or the electricity
(electric appliances).
I I M M P P O O R R T T A A N N T T
Resetting of the safety thermostat must be
carried out by specialised personnel; con-
tact the Service Centre.
Tampering with the safety thermostat
invalidates the warranty.
E E . . 9 9 F F u u s s e e r r e e p p l l a a c c e e m m e e n n t t
The electrical system protection fuse is located inside the
panel. To replace the fuse, unscrew the fuse holder cap and
remove it.
E E . . 1 1 0 0 B B e e f f o o r r e e c c o o m m p p l l e e t t i i n n g g t t h h e e i i n n s s t t a a l l l l a a t t i i o o n n
o o p p e e r r a a t t i i o o n n s s
Use soapy water to check all gas connections for leaks.
DO NOT use a naked flame to check for gas leaks. Light all the
burners separately and also together, to check correct
operation of the gas valves, rings and lighting.
For each burner, adjust the flame regulator to the lowest
setting, individually and together.
after completing the operations, the installer must instruct the
user on the correct method of use. If the appliance does not
work properly after carrying out all the checks, contact the local
after-sales service centre.
• When using solid fat, melt it separately then pour it in the
tank. Do not leave fat in the tank at the end of cooking.
• Restore the oil bath whenever it falls below the minimum
level, marked by the special reference notch ( ( d d a a n n g g e e r r o o f f
f f i i r r e e ) ) ;
• Particularly voluminous and non-drained foods can cause
splattering of hot oil.
• Place the basket with food to be cooked, slowly in the
boiling oil, making sure that the froth formed does not spill
over the edge of the tank. If this occurs, stop dipping the
basket for a few seconds.
.
23