Advertisement
Quick Links
Wall Mounting Unit
RK-C42WBT3
Thank you for purchasing this Wall Mounting Unit.
We recommend that you read this manual thoroughly before use in order to familiarize yourself with this unit.
Please store this manual in a safe place after reading it.
•
Mounting a plasma display television requires specific technical knowledge. Do not attempt to mount the unit by yourself.
•
Please be aware that screw holes and anchor bolts will remain in the wall surface if the Wall Mounting Unit is removed
after having been mounted to the wall.
Long-term use of the plasma display may result in discoloration of the wall surface due to heat/air emitted by the display.
For Assembly By Authorized Service Personnel Only
Consult authorized service personnel for the installation of this unit. Installation
instructions must be followed precisely in order to prevent accidents. We are
selling this product with the understanding that it will be assembled and installed
by properly trained and qualified service personnel.
We are not liable for any damage caused by faulty assembly,
faulty wall mounting, insecure wall mounting, misuse,
alterations, or natural disasters.
This unit weighs approx. 60 kg (approx. 132 lbs.) including plasma display
monitor. Incomplete or inadequate mounting of this unit to the wall may cause
it to fall down, resulting in potentially fatal accidents.
Please consult authorized service personnel for the installation of this unit.
Assembly and Mounting Instructions
Danger
Advertisement
Related Manuals for JVC RK-C42WBT3
Summary of Contents for JVC RK-C42WBT3
- Page 1 Wall Mounting Unit RK-C42WBT3 Thank you for purchasing this Wall Mounting Unit. We recommend that you read this manual thoroughly before use in order to familiarize yourself with this unit. Please store this manual in a safe place after reading it.
-
Page 2: Safety Precautions
Safety Precautions The following section describes the symbols used in this manual. Read this section prior to using the product for correct usage. The following items contain information for your safety. Follow these precautions precisely. Warning and Caution are defined as follows: Danger Improper handling in disregard of these notices may result in danger of death or bodily harm. - Page 3 Mounting the Wall Unit Plasterboard/Thin Plywood Do not install the Wall Mounting Unit in a location which is hot or humid or which may become wet, as the presence of excessive moisture may lead to fire or electric shock. Do not install the Wall Mounting Unit near the blower or air inlet of an air conditioner.
-
Page 4: Tools Required For Assembly
Consult authorized service personnel for electrical work. Using power cords damaged during installation (i.e., exposed or severed wiring) may result in fire or electric shock. Conduct the work with adequate working space. Damage or bodily injury may result from working under unsuitable conditions. Avoid mounting this unit in areas where there is electrical wiring or water pipes, as fire or electric shock may result. - Page 5 <Before Attaching Plasma Display> The Wall Mounting Unit is sold with Frame q and Wall Mounting Unit w fixed together. The following steps should be performed before attaching the plasma display. 1. Take the left and right Frame Fastening Screw Components and remove the Fastening Screw, Spacer Ring, Flat Washer, and Spring Washer.
-
Page 6: Instructions For Assembly
Mounting the Plasma Display Fasten all bolts and screws securely. Failure to do so may cause the plasma display and Wall Mounting Unit to fall down, causing potentially fatal accidents. Improper positioning/installation of the Wall Mounting Unit on the wall may cause the unit to fall down. Danger Check the structure, material, and strength of the mounting surface thoroughly and carry out installation in a suitable location. - Page 7 <Instructions for Assembly, cont’d> Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when Caution putting these together, as fingers will get trapped, causing injury. 3. Identify the Rotation Shaft Screws of the Wall Mounting Unit. Check that the left and right Rotation Shaft Screws are secure, as the Rotation Jaw of the Frame (attached to the plasma display) will be inserted into the Rotation Shaft Screw Component of the Wall Mounting Unit w.
- Page 8 <Instructions for Assembly, cont’d> Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when Caution putting these together, as fingers will get trapped, causing injury. 5. Fix the Frame and Wall Mounting Unit. Combine the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers (from the two pairs of Frame Fastening Screw Components that were put aside when detaching the Frame q from the Wall Mounting Unit w) as shown below and fasten them securely using a screwdriver.
- Page 9 <Instructions for Assembly, cont’d> Grip the plasma display firmly while adjusting the angle, as the display could tip over and cause Caution injury. Adjusting the Angle of the Plasma Display ＊ The angle of the Wall Mounting Unit can be adjusted to 0 , 5 , 10 , 15 , and 20 . 1.
- Page 10 <Instructions for Assembly, cont’d> Connecting the Power Cord and System Cables Grip the plasma display firmly while connecting the power cord/system cables, as the display Caution may tip over and cause injury. 1. Check the Frame Fastening Screws. Check that the two Frame Fastening Screws on the upper left and right sides of the Wall Mounting Unit are securely fastened.
- Page 11 <Instructions for Assembly, cont’d> Brace the plasma display when connecting the power cable or system cables. Failure to do so Caution may allow it to tip over, potentially causing injury. 3. Remove the Rotation Shaft Screws and Spacer Rings at the bottom left and right of the Wall Mounting Unit. ＊...
- Page 12 <Instructions for Assembly, cont’d> Brace the plasma display while connecting the power cord or system cables, as the display may Caution tip over, causing injury. 5. Connect the power cable and system cables to the plasma display. ＊ Be careful not to let the cables become caught between the plasma display and the Wall Mounting Unit. 6.
- Page 13 <Instructions for Assembly, cont’d> 7. Set the angle of the plasma display. Hold the upper part of the plasma display with one hand and set the display to the desired angle with the other hand, using the Angle Adjustment Lever on the Wall Mounting Unit. 8.
- Page 14 <Instructions on Removing the Plasma Display> Danger This task must be performed by at least two persons. 1. Hold the upper middle of the plasma display and set the Angle Adjustment Lever to 0 . ＊ If the Angle Adjustment Lever has been fastened, remove the Angle Adjustment Lever Lock Screw before performing this task.
- Page 15 <Instructions for Removing the Plasma Display, cont’d.> Danger This task must be performed by at least two persons. 3. Remove the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers of the two Frame Fastening Screw Components at the upper left and right of the Wall Mounting Unit. 4.
- Page 16 © 2004 VICTOR COMPANY OF JAPAN, LIMITED <External Dimensions> Wall Mounting Holes (Outer edge) 2-φ5 2-φ8 VICTOR COMPANY OF JAPAN, LIMITED 42-inch Display 2-φ5 2-φ8 F Section Ｆ Wall Mounting Unit Exterior F Section Details 2-φ5 2-φ5 2-φ8 13 1 (Units in millimeters) RK-C42WBT3-INST-0405-A 20° 2-φ8...