Related Manuals for G.I.KRAFT GI35114
Summary of Contents for G.I.KRAFT GI35114
- Page 1 G.I.KRAFT Owner’s Manual GI35114 The equipment is approved by following car manufacturers...
-
Page 2: Table Of Contents
Contents 1 、 Introduction 2 、 Specifications 3 、 Installation 4 、 Precautions 5 、 Controls 6 、 Operation 7 、 Repair and Maintenance 7-1 、 Exploded View 7-2 、 Troubshooting Electrical Diagram 、 9 、 Accessories and Spareparts List 10 、... -
Page 3: Introduction
Introduction Introduction These models battery charger/booster are intended for charging and starting batteries GI35114 with jump start function that are usually used in cars,trucks,motorcycles,boats,etc. Page.1... -
Page 4: Specifications
Specifications Model GI35114 Parameters Input voltage 2.5/20 Power(KVA) Charge voltage 12/24 （ V ） 20.25.35.45. Effective charge current(6gears) 55.72 Chrging direction (N degree) 1800 Instant current(A) 20/1500 Reference Capacitance 410*350*795 Dimensions(mm) Weight(kg) Input cord length(mm) 3000 Work cable length 3000+3000 (mm) Page.2... -
Page 5: Installation
Installation 1 、 Open package and find out Owner’s Manual. 2 、 Check the supplied of accessories according to packing list that attached with Owner’s Manual. 3 、 Properly install this equipment as following diagram. Inspect the unit for any damage. If so, contact your local distributor or service agency. -
Page 6: Precautions
Precautions 1 、 Select a correct location to place the unit 2 、 Do not move or operate unit where it could tip 3 、 Use cart or unit handle to move unit 4 、 Charging produces explosive gases,Never smoke or allow a spark or flame in vicinity of battery or engine. -
Page 7: Controls
Controls 1 、 Handle 2 、 12V/24V Selection 3 、 12V indicator 4 、 24V indicator 5 、 Power indicator 6 、 Timer 7 、 Current 8 、 Voltmeter 9 、 Ammeter Page.5... -
Page 8: Operation
,and 4,5,6 are fast charge.usually,time for fast charge is 60 mins. 4) 、 Connect input power, charging time can be set within 60 mins by timer ,The charger stops automatically when it reaches pre-set time. GI35114 Charing Connections: 12V charging connection 24V charging connection 1 、 Charging 1) 、... - Page 9 GI35114 ump-start connection 24Vjump-start connection 2 、 Jump-starting 1) 、 Select 12V or 24V 2) 、 Connect work cables to battery charger terminals as above diagram,and then connect clips from battery charger to the terminals of battery 3) 、 Connect input power.
-
Page 10: Repair And Maintenance
Repair and Maintenance 1 、 Exploded view Rectifier Main transformer A/C contactor Front view 24V positive 12V positive positive post post positive post post Jump-start Charging negative negative post post GI35114 Rear view Page.8... -
Page 11: Troubshooting
2 、 Troubleshooting Trouble Probable cause Remedy No input power (1)incorrect input power （ 1 ） Check input power connection connection （ 2 ） Turn power switch to “on” (2)Power switch in”off” position position Timer does not work （ 1 ） Charging time has not adjusted （... -
Page 12: Electrical Diagram
Page.10... -
Page 13: Accessories And Spareparts List
Accessories and spareparts list Accessories and spareparts list Handle Front stand Rectifier Amperage switch Timer Power switch Wheel Voltmeter Ammeter Ground clamp Output cord R marks: 1)Optional orders for above accessories and spareparts are available. 2)Model and parts number required when ordering parts from your local distributor or service agency.