Table of Contents
Advertisement
3.2
Servo circuit
3.2.1 Switching point
•
Signal
(A1)
Stairstep signal
•
(A2)
Alignment tape (SP,stairstep,PAL) [MHPE]
•
Mode
(B)
PB
•
Equipment
(C)
Oscilloscope
•
Measuring point (D1)
VIDEO OUT terminal (75Ø terminated)
•
(D2)
TP106 (PB. FM)
•
External trigger
(E)
TP111 (D.FF)/slope : –
•
Adjustment part
(F)
Jig code "5A"
•
Specified value
(G)
7.5 ± 0.5H
•
Adjustment tool
(H)
Jig RCU [PTU94023B]
(1) Play back the signal (A1) of the alignment tape (A2).
(2) Apply the external trigger signal to D.FF (E) to observe
the VIDEO OUT waveform and V.PB FM waveform at the
measuring points (D1) and (D2).
(3) Set the VCR to the manual tracking mode.
(4) Adjust tracking so that the V.PB FM waveform becomes
maximum.
(5) Set the VCR to the Auto adjust mode by transmitting the
code (F) from the Jig RCU. When the VCR enters the
stop mode, the adjustment is completed.
(6) If the VCR enters the eject mode, repeat steps (1) to (5)
again.
(7) Play back the alignment tape (A2) again, confirm that the
switching point is the specified value (G).
Trigger point
Switching point
Fig. 3-2-1a
3.2.2 Slow tracking preset
Signal
(A1)
• Ext. input
(A2)
• Color (colour) bar signal [PAL]
(A3)
• Color (colour) bar signal [NTSC]
Mode
(B1)
• VHS SP -
(Notes)
(B2)
• VHS LP -
(B3)
• VHS SP -
(B4)
• VHS EP -
Measuring point
(D)
• TV-Monitor
Adjustment part
(F)
• Jig RCU: Code "71" or "72"
Specified value
(G)
• Minimum noise
Adjustment tool
(H)
• Jig RCU [PTU94023B]
(1) Record the signal (A2) in the mode (B1), and play back
the recorded signal.
(2) Set the VCR to the manual tracking mode.
(3) Set the VCR to the FWD slow (+1/6x) mode.
(4) Transmit the code (F) from the Jig RCU to adjust so that
the noise bar becomes the specified value (G) on the TV
monitor in the slow mode.
(5) Set the VCR to the Stop mode.
(6) Confirm that the noise bar is (G) on the TV monitor in
the slow mode.
(7) Repeat steps (3) to (6) in the REV slow (–1/6x) mode.
(8) Repeat steps (1) to (7) in the mode (B2).
(9) Record the signal (A3) in the mode (B3), and play back
the recorded signal.
(10) Repeat steps (2) to (7).
V.sync
V. rate
Switching point
(PAL)
(NTSC)
(11) Repeat steps (9) and (10) in the mode (B4).
Note:
• For FWD slow (+1/6x) playback, transmit the code "08"
from the Jig RCU to enter the slow playback mode, and
transmit the code "D0" for REV slow (–1/6x) mode.
3.3 Video circuit
3.3.1 D/A level
•
Signal
(A1)
Ext. S-input / Ext. input
•
(A2)
Color (colour) bar signal [PAL]
•
(A3)
S-VHS tape
•
Mode
(B)
S-VHS
•
EE
•
Equipment
(C)
Oscilloscope
•
Measuring point (D)
Y OUT terminal (75Ø terminated)
•
Adjustment part
(F)
VR1201 (D/A LEVEL ADJ)
[2D DIGITAL board]
•
Specified value
(G)
1.00 ± 0.015 Vp-p (reference value)
(Note)
(1) Insert the cassette tape (A3) to enter the mode (B).
(2) Observe the Y OUT waveform at the measuring point (D).
(3) Check the Y level value when the External S-input (Y/C
separated video signal).
(4) Switch the input signal to the External input (composite
video signal), and adjust the adjustment part (F) so that
the Y level becomes the same value observed in step
(3).
Note:
• The specified value (G) is just a reference value to be
obtained when the External S-Video (Y/C separated
video) signal is input. In actual adjustment, set it to
the value observed in step (3).
H. rate
Fig. 3-3-1a
3.3.2 EE Y/PB Y (S-VHS/VHS) level
•
Signal
(A1)
Ext. input
•
(A2)
Color (colour) bar signal [PAL]
•
Mode
(B1)
EE
•
(B2)
S-VHS SP
•
(B3)
VHS SP
•
Equipment
(C)
Oscilloscope
•
Measuring point (D)
Y OUT terminal (75Ø terminated)
•
EVR mode
(F1)
Jig code "57"
•
EVR address
(F2)
A : 11
•
(F3)
Jig code "21" twice
•
(F4)
Jig code "18" or "19" (Channel +/-)
•
Specified value
(G)
1.00 ± 0.05 Vp-p
•
Adjustment tool
(H)
Jig RCU [PTU94023B]
(1) Set the VCR to the mode (B1)
(2) Observe the Y OUT waveform at the measuring point (D).
(3) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
Y level
D/A level
3-2
Advertisement
Table of Contents
