Advertisement
Quick Links
Advertisement
Related Manuals for JETWAY JBC501F797
Summary of Contents for JETWAY JBC501F797
- Page 1 Quick Installation Guide NO. G03-JC501QIG03-F Rev: 2.1 Release date: 2021-1-19...
-
Page 2: To Open The Chassis
Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification. 1. To Open the Chassis Locate the screws in the spots marked on the Turn over the barebone system with the top cover of the system and unscrew them heatsink upwards, as the photo shows. - Page 3 Remove the IO panels and lift the cover up to For CPU installation, user needs to remove open the chassis. For user to have a clear the screws on the marked spots to dissemble view of layout, we may unplug some of the the motherboard form chassis cover.
- Page 4 2. To Install CPU Find CPU socket on the board. Please make Remove the plastic protective cover from the sure that CPU socket is facing towards you socket (Put it to the original place if CPU is and the level is on you right hand side. not installed.
- Page 5 Alignment Key Alignment Key Golden Finger Indicator Make sure that Pin-1 Golden Finger Indicator in the place as shown in the above photo and match the two alignment keys on the CPU with two points of the socket. CPU can only be correctly installed in this direction. Incorrect installation might cause damage to CPU.
- Page 6 3. To Install Heatsink Thermal pads P/N: HCS3XXHS2-F *1 pcs 20*20*0.5mm Bottom Side Paste Here! Tear off the Protective films Find the above CPU heatsink and CPU thermal pad package. Remove the protective films on the both sides of the pad and apply it upon the bottom side of the heatsink for better heat conduction.
- Page 7 P/N: HCS501HS2-F *1 pcs, 25*25*1 mm 4. See to it that the silicone gel bars are in their 5. Apply corresponding thermal pads to chipset original places for better heat dispassion and heat sink. When installation finished, tear off the shockproof before installing the board to the system protective film from the pads before assembling the cover.
- Page 8 4. To Install SO-DIMM to the board Find the SO-DIMM slot on the board for further installation. Open the 2* ejects tabs before SO-DIMM installation. Press Down Adjust compatible SO-DIMM & Press down the SO-DIMM until the golden-finger side fully inserted into the slot.
- Page 9 5. To Install WI-FI Card Please refer to the following instructions for the installation of the Wi-FI card into M.2 PCIe slot. Locate the M.2. PCIe, type-2230 slot on Remove the marked screw nut reserved the board. for M.2 SATA card installation first.
- Page 10 Insert the gold-figure side of compatible Lock the card to the board by tightening up card into M.2. PCIe slot. See to it that the the screw nut to the marked spot. golden-figure side is fully inserted into the slot. Locate the reserved Wi-Fi antenna holes on the back panel.
- Page 11 Back-side View: Put the metal ring into the antenna head at first, and then push this antenna head into antenna hole of the rear panel. Front-side View: Put the other washer① into the antenna head, and then lock the antenna head to the front side of the back panel with the with hexagonal bolt②and tighten it up.
- Page 12 The metal hats on the end of the antenna Tear off the tape to find metal hats of Wi- string are sealed by acetate tape to avoid Fi antenna string. possible damage to the system. Press the metal hat on the end of the Connect the external Wi-Fi receiver antenna string to the antenna slot on the antenna to the antenna connector on the...
- Page 13 6. To Install M.2 SATA Card Locate the M.2 SATA slot on the board. Remove the screw and nut fixed at Prepare compatible M.2 SATA or M.2 default location (Skip step 2 & 3 and go SSD card. Deferent types of cards come straight to Step 4 if you are going to use of different length.
- Page 14 Align and insert the gold-figure side of Lock the card to the board by tightening the compatible M.2 SATA card into the up the previously-removed screw nut to slot. Make sure that the golden-figure the marked spot. side is fully inserted into the slot. 7.
- Page 15 Lock the SATA hard disk to one of the Lock the SATA hard disk to the other racks by tightening the screws in the rack by tightening the screws in the marked spots. marked spots. To connect onboard SATA port. To connect SATA hard disk driver.
- Page 16 Plug this side of the cable to SATA Lock the racks with SATA HDD installed power-in connector and SATA connector to its original places by tightening the of the hard disk. screws in the marked spots. Plug the other sides of the cables into the SATA power connector and SATA port connector on the board.
- Page 17 8. To Wall Mount the System Install wall mount rack to the system by tightening the screws in the marked positions. Then lock the other three screws on the other side in the same way. Wall mount the system by tightening two screws in the marked positions. Then tighten up the other two screws in the marked positions on the other rack.