Honeywell H4W2PER2 Series Quick Installation Manual page 2

2. Using the mounting template as a guide, drill three pilot holes in the mounting surface,
then hammer the supplied anchors into the holes.
3. Drill a cable entry hole in the mounting surface, then pull the required cables through the
hole.
Mounting and Aiming the Camera
1. Remove the dome cover from the camera assembly using the supplied Allen key.
2. If you are using a microSD card with the camera, install it before continuing. See below for
details.
1. Push and
slide metal
shell to
unlock
position.
3. Connect the Ethernet cable to the RJ-45 port on the camera.
4. If the other end of the Ethernet cable is not connected to a PoE (Power-over-Ethernet)
switch or NVR, connect the power connector of the camera to a 12 VDC power source.
5. Fix the camera assembly to the mounting surface using the supplied screws.
6. Aim the camera lens in the desired direction, then tighten the screws on the camera
assembly.
7. Reattach the dome cover.
Logging On to the Camera
If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be configured
using the NVR.
To log on remotely from a PC, install the Unified Tool from the software and documentation DVD,
find the camera on the network, and then open the web browser. The default user name is admin
(case-sensitive) and the default password is 1234.
Note
Only Internet Explorer 11 (or later) is supported.

IP address of the device is assigned automatically by DHCP server. If the DHCP server is not

available, the device will acquire 192.168.1.108 as the default IP address.
Adjusting the Zoom and Focus Settings
After you have logged on to the camera, go to Setup  Camera  Conditions  Zoom and Focus to
fine-tune the camera's zoom and focus settings.
© 2021 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.
2. Open 3. Insert microSD 4. Close metal
metal card. shell and
shell. slide to lock
position.
Recommended Recorders
HEN*4 8/16/32/64-channel Focus 4K NVRs (H.264 and H.265)
HEN*3 4/8/16/32-channel Performance Series NVRs (H.264 and H.265)
Regulatory Statements
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
North America The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No.
60950-1.
Europe The manufacturer declares that the equipment supplied is compliant with the European
Parliament and Council Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (2015/863/EU), the Low Voltage Directive (2014/35/EU) and the
essential requirements of the EMC directive (2014/30/EU), conforming to the requirements of standards
EN 55032 for emissions, EN 50130-4 for immunity, and EN 62368-1 for electrical equipment safety.
WEEE (Waste Electrical and Electronic Equipment)
Correct disposal of this product (applicable in the European Union and other European
countries with separate collection systems). This product should be disposed of, at the end of
its useful life, as per applicable local laws, regulations, and procedures.
North America
715 Peachtree St. NE Atlanta, Newhouse Industrial Estate
GA 30308 Motherwell Lanarkshire ML1 5SB
United Kingdom
www.security.honeywell.com www.security.honeywell.com/uk
Tel: 1 800 323 4576 Tel: +44 (0) 1928 378005
Document 800-26630-A, 03/2021
Europe Middle East
Emaar Business Park, Building No. 2,
Sheikh Zayed Road
P.O. Box 232362
Dubai, United Arab Emirates
www.security.honeywell.com/me
Tel: +971 4 450 5800