Related Manuals for Toshiba PDP 37 Series
Summary of Contents for Toshiba PDP 37 Series
- Page 1 Confidential TOSHIBA PDP 37-SERIES 42WP37E, C, F, H … VGA type 50XP37E, C, F, H … XGA type TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 2 1 Slot Structure to 4 Slot Structure • Power consumption 42“ : • • 295W→235W, 50“ : 495W→435W Zoom in Function （２Ｘ２、３Ｘ３） • DISITAL ZOOM function （Ｘ２Ｘ３ ) • ２ In screen function （ POP 、 PIP ） • TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 3 Destination Type Country / Region 42WP37E England and Europe 50XP37E 42WP37C China 50XP37C 42WP37F Korea 、 Russia , Australia 50XP37F 42WP37H Hong Kong 、 Singapore 、 Middle East 50XP37H TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 4 POWER CORD x2,REMOCON 50XP37E COMPONENT option MANUAL x5 42WP37C COMPOSITE x1 POWER CORD x1,REMOCON 50XP37C COMPONENT MANUAL x2, WARRANTY 42WP37F x2COMPOSITE x1 POWER CORD x2,REMOCON 50XP37F COMPONENT MANUAL x3, WARRANTY 42WP37H COMPOSITE x1 POWER CORD x1,REMOCON 50XP37H COMPONENT MANUAL x2 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 5 *9 Points Digital Zoom x2 and x3 Zoom Press Zoom Key EXIT EXIT TOSHIBA TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 6 *9 Points Digital Zoom x2 ZOOM MOVE EXIT Press Zoom Key EXIT TOSHIBA TOSHIBA Original Picture Zoom Picture TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 7 *9 Points Digital Zoom x3 ZOOM MOVE EXIT Press Zoom Key EXIT TOSHIBA TOSHIBA Original Picture Zoom Picture TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 8 New Function : Dual Picture *Two Image can be displayed simultaneously *Picture In Picture *Picture and Picture *Picture out Picture TOSHIBA TOSHIBA TOSHIBA PRESENTATION PRESENTATION PRESENTATION TOSHIBA TOSHIBA TOSHIBA All Signals Combination is available as E.g. PC- Composite, Composite – Component S-video –...
- Page 9 Data Drive (Lower Right) Data Drive (Lower Left) Speaker terminal Power switch Sustain connection (Upper) Sustain connection (Lower) Front SW. & Remote receiver Line filter Power supply 1 PC_type_Input terminal BNC Composite/Component Video 2 BNC Component Video 3 SCART Video 4 n=20sheets TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 10 Service Hint Remove : 4screws ( 6screws ( 16screws ( for PDP Back Cover V1 S1 SVM 8page TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 11 Block Diagram TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 12 Power Supply TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 13 Power supply Block Diagram TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 14 PF-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 15 P-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 16 HX-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 17 HY-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 18 J-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 19 D-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 20 C1-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 21 SC-BOARD TOSHIBA ASIA OCEANIA SERVICE CENTRE...
-
Page 22: Su And Sd-Board
SU and SD-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE... -
Page 23: Ss, Ss2 And Ss3-Board
SS, SS2 and SS3-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE... - Page 24 Z-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 25 V1, S1 and H3-Board TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 26 Caution ： To remove P.C.B. , wait 1 minute after power was off for discharge from electrolysis capacitors R6443(Vbk) R590(Vda) R605(Vsus) TPVBK TP15V TPV15 TPVSUS TPVDA V1 S1 V1 S1 R6557( ) R6477(Vad) R6774(Ve) TPSC1 TPVAD TPVSCN TPVSET TP15V TPVDA TOSHIBA ASIA OCEANIA SERVICE CENTRE 12page...
- Page 27 Trouble shooting guide 1. Power LED Blinking timing chart Blinking Blinking timing Check point 3sec Once Main/Micom/Power SCAN Driver-1 3.3V SOS 5V SOS Power SOS SCAN Driver-2 TEMP(Not used) SUS Driver SVM 25page TOSHIBA ASIA OCEANIA SERVICE CENTRE...
-
Page 28: Self Check
OFF-TIMER button on the remote control, and the screen will show :- If the CCU ports have been checked and found to be incorrect Or not located then " - - " will appear in place of " OK " TOSHIBA ASIA OCEANIA SERVICE CENTRE... - Page 29 Trouble shooting guide 1. No Power Does turn the power LED? Check PF board But no AC supplied Check Check Check AC power cord P board Fuse F900, F901 or power source SVM 26page TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 30 Drive Circuit LED indicator TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 31 2. No Picture No Picture Check Check Check SC board SS board What’s signal? Composite/Component/ RGB video signal SC board D board SS board Check IC9151 PC signal HY/HZ/HT board HX board SVM 26page TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 32 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 33 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 34 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 35 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
-
Page 36: Local Screen Failure
Local screen failure Plasma display may have local area failure on the screen. The possible defect P.C.B. for each local area. TOSHIBA ASIA OCEANIA SERVICE CENTRE... - Page 37 Option Menu. This Option Menu is useful for special function required customers. This should be set at the installation stage. The end user could not set or change these because of hidden On screen menu. TOSHIBA ASIA OCEANIA SERVICE CENTRE...
-
Page 38: Option Setting
Option Setting How to access the Option menu TOSHIBA ASIA OCEANIA SERVICE CENTRE... - Page 39 TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 40 How to set Remocon User Level and Remote ID off. 1. Access service mode (CAT-mode) and press SET UP key on remote. 2. Access Hidden option menu. 3. Change Remote con User Level and/ or Remote ID set to Off TOSHIBA ASIA OCEANIA SERVICE CENTRE...
-
Page 41: About Lead Free Solder (Pbf)
About lead free solder(PbF) Note: Lead is listed as (Pb) in the periodic table of elements. Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used. TOSHIBA ASIA OCEANIA SERVICE CENTRE... - Page 42 About lead free solder(PbF) This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d suggest the use of Pb free solder as well, although Pb solder may be used. PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB. TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 43 Caution ·Pb free solder has a higher melting point than standard solder. Typically the melting C) higher. point is 50 ~ 70 F (30~40 Please use a high temperature soldering iron and set it to 700 ± 20 F (370 ± 10 C). ·Pb free solder will tend to splash when heated too high (about 1100 F or 600 C). If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder. ·After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the opposite side. (see figure below) TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 44 Any Question? Disassembling and Assembling TOSHIBA ASIA OCEANIA SERVICE CENTRE...
- Page 45 Any Question? Disassembling & Assemble TOSHIBA ASIA OCEANIA SERVICE CENTRE...