Advertisement
Quick Links
1.General Description and Spcification
1.1 General Description
This product is a Class 2 SMT Bluetooth Module used CSR BC5-MultiMedia
External. It provides data and voice communications. It interfaces with a host through
USB or UART and support data rate up to 12M/3Mbps.
General Fetures:
Class 2 Bluetooth Module
■
Bluetooth Spec. V2.1+EDR Compliant
■
Support Firmware Upgrade
■
USB 2.0 and UART Host Interface
■
Multi-Configurable I2S, PCM or SPDIF Interface
■
Integrated 1.5V and 1.8V Linear Regulators
■
Integrated Switched-mode Regulator
■
Integrated Battery Charger
■
Integrated Microphone bias& LED Driver
■
64MIPS Kalimba DSP Co-processor
■
Built in 16-bit Stereo Codec- 95dB SNR for DAC
■
Enhanced Audibility and Noise Cancellation
■
Support for 802.11 Co-existence
■
Green (RoHS Compliant)
■
1.2 Device Details
Radio
■ Common TX/RX terminal simplifies external matching; eliminates external antenna switch
■ BIST minimises production test time
■ Bluetooth v2.1 + EDR specification compliant
Transmitter
■ 4dBm RF transmit power with level control from onchip 6-bit DAC over a dynamic range >30dB
■ Class 2 and Class 3 support without the need for an external power amplifier or TX/RX switch
Receiver
■ Receiver sensitivity of -70dBm
BC05 Module Spec.
Shenzhen Synchron Electronics Co.,Ltd. 2010.11
Advertisement
Related Manuals for Sony BC05
Summary of Contents for Sony BC05
- Page 1 BC05 Module Spec. Shenzhen Synchron Electronics Co.,Ltd. 2010.11 1.General Description and Spcification 1.1 General Description This product is a Class 2 SMT Bluetooth Module used CSR BC5-MultiMedia External. It provides data and voice communications. It interfaces with a host through USB or UART and support data rate up to 12M/3Mbps.
- Page 2 ■ Integrated channel filters ■ Digital demodulator for improved sensitivity and cochannel rejection ■ Real-time digitised RSSI available on HCI interface ■ Fast AGC for enhanced dynamic range Baseband and Software ■ 16Mbit external Flash ■ 48Kbyte internal RAM, allows full-speed data transfer, mixed voice/data and full piconet support ■...
- Page 3 ■ On-chip high-efficiency switched-mode regulator; 1.8V output from 2.7V to 4.4V input ■ Power-on-reset cell detects low supply voltage ■ 10-bit ADC and 8-bit DAC available to applications ■ On-chip charger for lithium ion/polymer batteries 1.3 Specification Chipset CSR BC05 Multimedia Specification Version Bluetooth V2.1+EDR Power Class Class 2 Frequency Band 2400~2483.5MHz...
-
Page 4: Package Information
2.Package Information 2.1 Pinout Diagram Figure 1: BC05 Module Pinout(Top View) 2.2 Terminal Functions... - Page 5 PIO10 PIO11 Programmable input/output line PIO12 PIO13 Ground Positive supply for SPI/PCM ports and PIO[15:4] and BC05 MM Flash Pads, Connect to 3.3V Ground VDD_Flash Positive supply for Flash Memory ,Connect to 3.3V VDD_USB Positive supply for UART/USB ports +1.8V...
- Page 6 SPI_MOSI SPI data intput Take high to enable high-voltage linear regulator VRE_IN and switch-mode regulator Lithium ion/polymer battery positive terminal. VDD_BAT Battery charger output and input to switch-mode regulator Ground VDD_CHG Battery charge LED1 LED Driver LED0 Ground SPK_L_N Speaker output negative, left SPK_L_P Speaker output positive, left SPK_R_N...
- Page 7 Figure 2: BC05 Module package Dimensions...
-
Page 8: Hardware Description
3.Hardware Description 3.1 Block Diagram Figure 3: BC05 Module Block Diagram 3.2 RF Ports... - Page 9 The DC level must be set at VDD_RADIO. 3.3 UART Ports BC05 Module UART interface provides a simple mechanism for communicating with other serial devices using the RS232 protocol. When BlueCore5 ‑ Multimedia External is connected to another digital device, UART_RX and UART_TX transfer data between the two devices.
- Page 10 This is a full speed (12Mbits/s) USB interface for communicating with other compatible digital devices.BC05 Module acts as a USB peripheral, responding to requests from a master host controller such as a PC. As USB is a master/slave oriented system (in common with other USB peripherals), BlueCore5 ‑...
- Page 11 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 12 Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
- Page 13 BTMS3 Install manual BT module BT module and Antenna Main board test Pass. BT Antenna Main board test Pass. Fix main board on Rear cabinet by screws. Fix the front, rear,top,bottom cabinet by screws. BT module Location BT module Location...