Recording From A Video Cassette Recorder; Manual Recording; Dv Automatic Recording (Dv Auto Rec) - Panasonic DMR-E500HS Operating Instructions Manual

Recording from a video cassette recorder

DVD POWER
TV
POWER
INPUT SELECT TV/VIDEO
INPUT SELECT
HDD
1 2
4 5
7 8
CANCEL
0
SKIP
;
STOP
∫
DIRECT NAVIGATOR
TOP MENU
SUB MENU
PROG/CHECK
DISPLAY
SETUP ERASE
Info DUBBING
e.g.: Connecting other video equipment to the L2 or DV input
terminals
≥Turn off the unit and other video equipment before connecting.
This unit
POWER POWER POWER
EJECT
PC CARD
SD CARD
HDD
S-VIDEO IN VIDEO IN L/MONO AUDIO IN R DV IN
L2
S-VIDEO IN VIDEO IN L/MONO - AUDIO IN - R
Yellow White Red
Audio/Video
S-Video
cable
§
cable
If the audio output of the other equipment is monaural, connect to L/
MONO.
§
The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.

≥DV automatic recording (DV AUTO REC)

When recording from the unit's DV terminal
Select the type of audio recording from "Select Audio CH for DV
Input" in the SETUP menu ( page 63).
VOLUME
CH
HDD, DVD
DVD SD/PC
PAGE
3
CH
6
AUDIO
9 AUDIO
VCR Plus+
CM SKIP
SLOW/SEARCH
PAUSE PLAY/x1.3
FUNCTIONS
FUNCTIONS
3 4 2 1
ENTER
ENTER
RETURN
TV GUIDE
TIME SLIP
REC MODE
REC MODE REC
¥ REC
CHAPTER STATUS
OPEN/CLOSE
TIME SLIP HDD DVD SD PC DRIVE SELECT x / 1.3
DVD
DV IN
DV Cable
(IEEE 1394, 4-pin)
Other video
equipment
page 52

Manual recording

[HDD] [RAM] [DVD-R]
Preparation
≥Connect a video cassette recorder to this unit's input terminals.
≥Press [HDD] or [DVD] to select the recording drive.
≥To adjust the audio recording level (
[Note]
When recording using this unit's input terminals, only the sound
received at the time of recording will be recorded.
As long as secondary audio that is recorded on the video cassette is
not output on the unit in play, it is not recorded.
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to L2 input terminals, select "L2".
2
Press [REC MODE] to select the
recording mode.
3
Start play on the other equipment.
4
Press [¥ REC].
Recording starts.
To skip unwanted parts
Press [;] to pause recording. (Press again to restart recording.)
To stop recording
Press [∫].
To record programs to fill up the remaining space on the disc
page 24, Flexible Recording
Almost all videos and DVD software on sale have been
treated to prevent illegal copying. Any software that has
been so treated cannot be recorded using this unit.
∫ To adjust the audio recording level
1 Before recording commences, press and hold [AUDIO] for
more than 3 seconds.
Audio Recording Level
L
d0
L
-¶
L/R
30 20 15 10 5 0 OVER
d0
R
R
2 Press [3, 4] to select "L/R".
To individually adjust a level press [3, 4] to select "L" (left) or "R"
(right).
3 Press [2, 1] to adjust the audio recording level and press
[ENTER].
≥Set the level to neutral again after recording is finished.
≥If the recording level is too high the audio will be distorted. Set it so
the audio level meter is not shaking (Maximum–10 dB to –5 dB is
an appropriate level).
≥The DV input is unaffected.
below)
RQT7394
51