Honda UMK450T Owner's Manual
  1. Manuals
  2. Brands
  3. Honda Manuals
  4. Brush Cutter
  5. UMK450T
  6. Owner's manual

Honda UMK450T Owner's Manual

Hide thumbs Also See for UMK450T:
Table of Contents

Advertisement

Quick Links

Honda UMK450T
OWNER'S MANUAL
xzkgd iq f Lrdk

Advertisement

Table of Contents
loading

Related Manuals for Honda UMK450T

Summary of Contents for Honda UMK450T

  • Page 1 Honda UMK450T OWNER’S MANUAL xzkgd iq f Lrdk...
  • Page 2 Brush Cutter and should remain with the Brush Cutter, if resold. The information and specifications included in this publication were in effect at the time of approval for printing. Honda M o t o r Co., Ltd. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever.
  • Page 3 This manual covers the operation and maintenance of the Honda BRUSH CUTTER UMK450T. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission.

  • Page 4: Table Of Contents

    CONTENTS 1. SAFETY INSTRUCTIONS ............ 3 2. SAFETY LABEL LOCATIONS ..........14 3. COMPONENT IDENTIFICATION ..........15 4. CONTROLS ..............17 5. PRE-OPERATION CHECKS ..........20 6. STARTING THE ENGINE ............38 7. TRIMMING OPERATION .............42 8. STOPPING THE ENGINE .............46 9. MAINTENANCE ..............47 10. TRANSPORTING ...............70 11.

  • Page 5: Safety Instructions

    To ensure safe operation For your safety and safety of others, pay special attention to these precautions: • Honda brush cutter is designed to give safe and dependable service if operated according to instructions. Read and understand the Owner’s Manual before operating the brush cutter.
  • Page 6 4MVR5D000.book Page 4 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Operator Responsibility • Never operate the brush cutter when tired, ill or under influence of alcohol or other drugs. • Any part from the machine is a potential source of danger if the machine is used in abnormal conditions or if the maintenance is not done correctly.
  • Page 7 4MVR5D000.book Page 5 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Operator Responsibility • While operating the brush cutter, always wear following protective clothing and protective devices. – Protective clothing Wear adequate clothes with long sleeves and long pants.The clothes must fit your body and button up or zip up the clothes securely.
  • Page 8 4MVR5D000.book Page 6 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Operator Responsibility * Safety boots Wear the safety boots with the non-slip sole and toe protector to protect your feet from the flying debris. Do not operate the equipment when barefoot or wearing open sandals.
  • Page 9 4MVR5D000.book Page 7 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Operator Responsibility • Do not operate the brush cutter with the grass deflector, labels, and other parts removed. Note that the grass deflector is provided for protection of the operator from the debris that are thrown from the wheeling cutting attachment.
  • Page 10 • The brush cutter is faulty when the engine is idling by returning the throttle but the cutting attachment keeps turning, and idle speed adjustment must be made. Consult your authorized Honda dealer. • Keep all nuts, bolts and screws tight to be sure the brush cutter is in safe working condition.
  • Page 11 Operator Responsibility • Do not use the brush cutter with worn or damaged parts. Parts must be replaced, or repaired. Replace worn or damaged parts with Honda genuine parts. Non equivalent quality parts may damage the machine and be prejudicial to your safety.
  • Page 12 4MVR5D000.book Page 10 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Operator Responsibility • Injury caused by vibration and cold: You may feel the prickling or burning pain in your fingers, and the fingers may lose color and feeling depending on your constitution. It is believed that these symptoms are brought by vibration and/or exposure to cold.
  • Page 13 4MVR5D000.book Page 11 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Child Safety • Keep children indoors and supervised at all times any outdoor power brush cutter is being used nearby. Young children move quickly and are attracted especially to the brush cutter and trimming activity. •...
  • Page 14 4MVR5D000.book Page 12 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Fire and Burn Hazard Gasoline is extremely flammable, and gasoline vapor can explode. Use extreme care when handling gasoline. Keep gasoline out of reach of children. • Store fuel in containers specifically designed for this purpose. •...
  • Page 15 4MVR5D000.book Page 13 Wednesday, September 26, 2018 4:44 PM To ensure safe operation Carbon Monoxide Poisoning Hazard Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. • If you run the engine in an area that is confined or even partially enclosed, the air you breathe could contain a dangerous amount of exhaust gas.

  • Page 16: Safety Label Locations

    Their meanings are explained on page 3. These decals are considered as a part of the brush cutter. Should one become detached or unreadable, contact your Honda dealer for its replacement. READ OWNER'S MANUAL...

  • Page 17: Component Identification

    4MVR5D000.book Page 15 Wednesday, September 26, 2018 4:44 PM 3. COMPONENT IDENTIFICATION Nylon-line cutting head: NYLON-LINE CUTTING HEAD THROTTLE TRIGGER ENGINE SWITCH GEAR CASE THROTTLE TRIGGER INTERLOCK GRASS DEFLECTOR FRAME SERIAL NUMBER U SHAPED HANDLE Cutting blade: CUTTING BLADE GEAR CASE GRASS DEFLECTOR...
  • Page 18 4MVR5D000.book Page 16 Wednesday, September 26, 2018 4:44 PM SPARK PLUG CAP (inside the top cover) CHOKE LEVER SPARK PLUG CLEANER TOP COVER MUFFLER ENGINE OIL FILLER PRIMING PUMP STARTER GRIP FUEL RETURN TUBE ENGINE SERIAL FUEL TANK CAP NUMBER FUEL TUBE Record the frame serial number (see page 15), engine serial number, date purchased in the spaces below.

  • Page 19: Controls

    4MVR5D000.book Page 17 Wednesday, September 26, 2018 4:44 PM 4. CONTROLS 1.Engine switch The engine switch enables and disables the ignition system. The engine switch must be in the ON position for the engine to run. Turning the engine switch to the OFF position stops the engine. ENGINE SWITCH 2.Priming pump Pressing the priming pump feeds the gasoline from the fuel tank to...
  • Page 20 4MVR5D000.book Page 18 Wednesday, September 26, 2018 4:44 PM 3.Choke lever The choke lever opens and closes the choke valve in the carburetor. The CLOSED position enriches the fuel mixture for starting a cold engine. The OPEN position provides the correct fuel mixture for operation after starting, and for restarting a warm engine.
  • Page 21 4MVR5D000.book Page 19 Wednesday, September 26, 2018 4:44 PM 5.Throttle trigger The throttle trigger controls engine speed. Pulling and releasing the throttle trigger shown below makes the engine run faster or slower. NOTE: The throttle trigger interlock must be depressed before the throttle trigger can be activated.

  • Page 22: Pre-Operation Checks

    4MVR5D000.book Page 20 Wednesday, September 26, 2018 4:44 PM 5. PRE-OPERATION CHECKS For safe and efficient trimming, always conduct a pre-operation checks. Perform the pre-operation checks on a firm, level surface with the blade stopped and make sure that the engine switch is in the OFF position. Before each use, look around and underneath the engine for signs of oil or gasoline leaks.
  • Page 23 4MVR5D000.book Page 21 Wednesday, September 26, 2018 4:44 PM Use 4-stroke motor oil that meets or exceeds the requirements for API service classification SE or later (or equivalent). Always check the API service label on the oil container to be sure it includes the letters SE or later (or equivalent).
  • Page 24 4MVR5D000.book Page 22 Wednesday, September 26, 2018 4:44 PM 2.Check the fuel level Use unleaded gasoline with a Research Octane Number of 91 or higher (a Pump Octane Number of 86 or higher). Never use gasoline that is stale, contaminated, or mixed with oil. Avoid getting dirt or water in the fuel tank.
  • Page 25 4MVR5D000.book Page 23 Wednesday, September 26, 2018 4:44 PM 1.Check the fuel level visually from the outside of the fuel tank while keeping the fuel filler neck upright. 2.If the fuel level is low, refuel the fuel tank until the level as specified. Remove the fuel tank cap gradually to release a pressurized air in the fuel tank.
  • Page 26 Gasolines containing alcohol If you decide to use a gasoline containing alcohol (gasohol), be sure it’s octane rating is at least as high as that recommended by Honda. There are two types of “gasohol”: one containing ethanol, and the other containing methanol.
  • Page 27 4MVR5D000.book Page 25 Wednesday, September 26, 2018 4:44 PM 3.Check the air cleaner CAUTION: Never run the engine without the air cleaner; rapid engine wear will result. 1.Move the choke lever to the CLOSED (upwards) position. 2.Loosen the screw and remove the air cleaner cover from the air cleaner body.
  • Page 28 4MVR5D000.book Page 26 Wednesday, September 26, 2018 4:44 PM 4.Check the throttle cable free play CHOKE LEVER AIR CLEANER COVER 1.Move the choke lever to the CLOSED (upwards) position. 2.Loosen the screw and remove the air cleaner cover from the air cleaner body.
  • Page 29 4MVR5D000.book Page 27 Wednesday, September 26, 2018 4:44 PM 5.Adjustment of the carrying harness Be sure to wear the carrying harness before using the brush cutter. Otherwise, injuries might occur due to its instability. 1.Wear the carrying harness so that the hip pad is on the right side of your body.
  • Page 30 4MVR5D000.book Page 28 Wednesday, September 26, 2018 4:44 PM 3.Roll the end of the harness toward your body and fasten it. Roll the end of the harness and fasten it.
  • Page 31 4MVR5D000.book Page 29 Wednesday, September 26, 2018 4:44 PM 6.Check the carrying harness 1.Put on the carrying harness. 2.Set the hook to the hanger. 3.Check that the hook is fastened to the hanger securely. CARRYING HARNESS HOOK HANGER HIP PAD...
  • Page 32 2.Check the tightness of the cutting blade nut. Tighten the nut if it is loose (see page 59). If it is hard to do it yourself, consult your authorized Honda dealer. 3.Check the cutting blade for wear, bend, crack and other damage.
  • Page 33 2.Check the cutting head for looseness. Tighten the cutting head securely if it is loose (see page 54). If it is hard to do it yourself, consult your authorized Honda dealer. 3.Check the nylon-line for fluffing. If the nylon-line is damaged, have the nylon-line advance according to the following procedures.
  • Page 34 4MVR5D000.book Page 32 Wednesday, September 26, 2018 4:44 PM 8.Check the grass deflector and plate Plate is equipped only with the nylon-line cutting head equipped model. • Never use the brush cutter without its grass deflector. Stones or other foreign objects thrown outward by the wheeling cutting attachment or contact with the wheeling cutting attachment could cause personal injury or property damage.
  • Page 35 4MVR5D000.book Page 33 Wednesday, September 26, 2018 4:44 PM Cutting blade equipped model: 1.Stop the engine with the engine switch to the OFF position. 2.Inspect the grass deflector to be sure that they are correctly installed and are not damaged. If the grass deflector is damaged, replace it before using the brush cutter.
  • Page 36 4MVR5D000.book Page 34 Wednesday, September 26, 2018 4:44 PM 9.Check the gear case • For safety, check the gear case for wear and damage before starting the engine. CAUTION: Wear heavy gloves to protect your hands, when working around the gear case.
  • Page 37 4MVR5D000.book Page 35 Wednesday, September 26, 2018 4:44 PM Cleaning the gear case: If there is contaminated material such as grass, thread, mud, or dirt in between the gear case, grass guard, and blade holder A, clean them using the following procedure. 1.Stop the engine with the engine switch to the OFF position.
  • Page 38 4MVR5D000.book Page 36 Wednesday, September 26, 2018 4:44 PM Inspect the drive bolt : Hold the drive bolt, move it left and right, and check if it is loose. If it is loose, the gear case must be replaced. Contact your Honda dealer for replacement. DRIVE BOLT...
  • Page 39 4MVR5D000.book Page 37 Wednesday, September 26, 2018 4:44 PM 10.Check all bolts and nuts Check the bolt and nut whether it is loosen before every work. If the bolts or nuts come loose, tighten them. 1.Check each bolt and nut for looseness. Tighten them securely if necessary.

  • Page 40: Starting The Engine

    4MVR5D000.book Page 38 Wednesday, September 26, 2018 4:44 PM 6. STARTING THE ENGINE • Exhaust gas contains poisonous carbon monoxide. Never run the engine in an enclosed area. Be sure to provide adequate ventilation. • Start the engine in a place away from the people, pets, and surrounding buildings.
  • Page 41 4MVR5D000.book Page 39 Wednesday, September 26, 2018 4:44 PM 2.To start a cold engine, move the choke lever to the CLOSED position. To restart warm engine, leave the choke lever in the OPEN position. CLOSED CHOKE LEVER OPEN CLOSED OPEN 3.Press the priming pump several times until the priming pump is filled with fuel.
  • Page 42 4MVR5D000.book Page 40 Wednesday, September 26, 2018 4:44 PM 4.Pull the starter grip lightly until you feel resistance while stepping on the carrying frame with your foot and holding the carrying frame with your hand, then pull briskly in the direction of the arrow as shown below.
  • Page 43 4MVR5D000.book Page 41 Wednesday, September 26, 2018 4:44 PM Carburetor Modification for High Altitude Operation. At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plugs and cause hard starting. Operation at an altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.

  • Page 44: Trimming Operation

    Read and understand the safety instructions on pages 3 to 13 before operating the brush cutter. If you notice any abnormal sound, smell, vibration, or other unusual signs, stop the engine immediately and consult your authorized Honda dealer. Brush cutter holding position adjustment: Stop the engine when adjusting the length of the carrying harness.
  • Page 45 The cutting attachment should not rotate with the engine idling. If there is rotation at idle, adjust the idle speed correctly before using the brush cutter. For idle adjustment, consult your authorized Honda servicing dealer. CARRYING...
  • Page 46 4MVR5D000.book Page 44 Wednesday, September 26, 2018 4:44 PM • Operate the brush cutter not by using your arm force but by using your waist so that the cutting attachment swings in a level arc from right to left. Hold the brush cutter so that you can shift your weight to the right leg then to the left leg safely and easily, and walk slowly with narrow strides.
  • Page 47 4MVR5D000.book Page 45 Wednesday, September 26, 2018 4:44 PM The line feeding action of the nylon-line cutting head: For this type of cutting head, the nylon-line advances when the cutting head is tapped against the ground while the engine is running. A grass deflector with cut-off knife must be used with it.

  • Page 48: Stopping The Engine

    4MVR5D000.book Page 46 Wednesday, September 26, 2018 4:44 PM 8. STOPPING THE ENGINE 1.Release the throttle trigger. 2.Turn the engine switch to the OFF position. CAUTION: Note that the cutting attachment keeps turning for a while by inertia after the engine is stopped. THROTTLE TRIGGER ENGINE SWITCH NOTE:...

  • Page 49: Maintenance

    OFF position to be certain the engine will not start accidentally. • The brush cutter should be serviced by an authorized Honda dealer unless the owner has proper tools and service data and feels he is mechanically qualified.
  • Page 50 (1) Service more frequently when used in dusty areas. (2) These items should be serviced by your servicing dealer, unless you have the proper tools and are mechanically proficient. Refer to the Honda shop manual for service procedures. (3) Log hours of operation to determine proper maintenance intervals.
  • Page 51 4MVR5D000.book Page 49 Wednesday, September 26, 2018 4:44 PM Tool kit The tools supplied are necessary for performing some periodic maintenance, simple adjustments and repairs. SPARK PLUG WRENCH 8×10mm WRENCH 5 mm HEXAGON WRENCH 4 mm HEXAGON WRENCH TOOL BAG...
  • Page 52 4MVR5D000.book Page 50 Wednesday, September 26, 2018 4:44 PM 1.Engine oil change CAUTION: If the engine has been running, the engine, muffler and the engine oil are very hot and they remain hot for a while after stopping the engine. To protect you from burn, wait until they cool down before starting the oil change.
  • Page 53 4MVR5D000.book Page 51 Wednesday, September 26, 2018 4:44 PM 3.Refill with the recommended oil (see page 21) to the upper limit (edge of the oil filler neck). 4.Install the oil filler cap. ENGINE OIL CAPACITY: 0.13 L Wash your hands with soap and water after handling used oil. OIL FILLER NECK ENGINE OIL FILLER CAP...
  • Page 54 4MVR5D000.book Page 52 Wednesday, September 26, 2018 4:44 PM 2.Air cleaner service A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction, service the air cleaner regularly. Service more frequently when operating the brush cutter in extremely dusty areas. Never use gasoline or low flash point solvents for cleaning the air cleaner element.
  • Page 55 4MVR5D000.book Page 53 Wednesday, September 26, 2018 4:44 PM 3.Inspect the air filter element, and replace it if it is damaged. Always replace the paper air filter element at the scheduled interval (see page 48). 4.Clean the air filter element if it is to be reused. Tap the paper air filter element several times on a hard surface to remove dirt, or blow compressed air [not exceeding 200 kPa (2.0 kgf/cm2, 29 psi)] through the filter element from the air cleaner...
  • Page 56 • To avoid severe personal injury, make sure that the engine switch is in the OFF position to prevent accidental starting. • Use a genuine Honda replacement cutting head or its equivalent. CAUTION: Wear heavy gloves to protect your hands when replacing the cutting head.
  • Page 57 4MVR5D000.book Page 55 Wednesday, September 26, 2018 4:44 PM 4.Turn the nylon-line cutting head counterclockwise to install it to the gear case. NYLON-LINE CUTTING HEAD GEAR CASE...
  • Page 58 4MVR5D000.book Page 56 Wednesday, September 26, 2018 4:44 PM Nylon-line replacement: • Never replace the nylon-line with a line of a different material, such as steel wire. • To avoid severe personal injury, make sure that the engine switch is in the OFF position to prevent accidental starting.
  • Page 59 4MVR5D000.book Page 57 Wednesday, September 26, 2018 4:44 PM 4.Prepare 3 metres of 2.4 mm diameter nylon-line and fold it in half, lengthwise. 5.Place the middle of the nylon-line in the notch in the reel and coil the nylon-line by turning in the specified direction. NOTCH NYLON-LINE LH DIRECTION...
  • Page 60 4MVR5D000.book Page 58 Wednesday, September 26, 2018 4:44 PM 7.Put the spool onto the cover at the position meet the line holding notches with the eyelets on the cover. Set the nylon-lines into the eyelets through the slits on upper side of the eyelets. LINE HOLDING NOTCHES SLIT EYELET...
  • Page 61 • To avoid severe personal injury, make sure that the engine switch is in the OFF position to prevent accidental starting. • Use a genuine Honda replacement cutting blade. CAUTION: Wear heavy gloves to protect your hands, when working around the cutting blade.
  • Page 62 4MVR5D000.book Page 60 Wednesday, September 26, 2018 4:44 PM 4.Grass deflector replacement Install the grass deflector in the proper position securely to protect you from the debris that are thrown from a wheeling cutting attachment. CAUTION: Wear heavy gloves to protect your hands, when working around the cutting attachment.
  • Page 63 4MVR5D000.book Page 61 Wednesday, September 26, 2018 4:44 PM Cutting blade equipped: 1.Place the grass deflector in a position that allows it to touch the gearbox. 2.Remove the grass deflector mounting bolts, and then remove the grass deflector. 3.Place the deflector holder on new grass deflector and align the bolt holes.
  • Page 64 4MVR5D000.book Page 62 Wednesday, September 26, 2018 4:44 PM 5.Spark plug service Recommended spark plug: CMR5H (NGK) To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. If the engine has been running, the muffler will be very hot, be careful not to touch the muffler.
  • Page 65 4MVR5D000.book Page 63 Wednesday, September 26, 2018 4:44 PM 4.Measure the plug gap with a feeler gauge. Correct as necessary by carefully bending the side electrode. The gap should be: 0.6 – 0.7 mm SIDE ELECTRODE 0.6–0.7 mm WASHER INSULATOR 5.Check that the spark plug washer is in good condition and thread the spark plug in by hand to prevent cross-threading.
  • Page 66 4MVR5D000.book Page 64 Wednesday, September 26, 2018 4:44 PM 6.Throttle cable check and adjustment Adjust the throttle cable free play properly. Adjustment: 1.Move the choke lever to the CHOKE LEVER AIR CLEANER CLOSED (upwards) position. COVER 2.Loosen the screw and remove the air cleaner cover from the air cleaner body.
  • Page 67 (i.e. throttle lever does not move while operating the throttle trigger). 7.After adjustment, check the throttle trigger for smooth operation. Consult your authorized Honda dealer if necessary. THROTTLE TRIGGER 8.Reinstall the air cleaner cover and tighten the screw securely.
  • Page 68 4MVR5D000.book Page 66 Wednesday, September 26, 2018 4:44 PM 7.Engine cooling fin inspection Inspect the cooling fin visually through the cover. If there are dry grass, leaves and mud clogged, consult your service dealer for cleaning it. COOLING FINS (Inside the top cover)
  • Page 69 4MVR5D000.book Page 67 Wednesday, September 26, 2018 4:44 PM 8.Fuel filter and fuel tank cleaning Note that the clogged fuel filter can cause poor engine performance. Water and dust, dirt or contaminated material in the fuel tank cause a poor engine performance. Gasoline is extremely flammable and is explosive under certain conditions.
  • Page 70 4MVR5D000.book Page 68 Wednesday, September 26, 2018 4:44 PM 3.Pull out the fuel filter with the mechanic’s wire from the fuel filler neck gently. MECHANIC’S WIRE FUEL FILTER 4.Inspect the fuel filter of its dirt. If the fuel filter is dirty, wash it gently with nonflammable or high flash point solvent.
  • Page 71 Check fuel tubes for cracks and any other deterioration and confirm that there is no leakage of fuel on the fuel tubes. If you notice any abnormal symptoms on the fuel tubes, contact an authorized Honda dealer. FUEL TUBES 10.Grease of gear case 1.Remove the bolt of gear case.

  • Page 72: Transporting

    4MVR5D000.book Page 70 Wednesday, September 26, 2018 4:44 PM 10. TRANSPORTING CAUTION: To avoid severe burns or fire hazards, let the engine cool before transporting the brush cutter. Always turn the engine switch to the OFF position. Make sure the fuel cap is securely tightened.

  • Page 73: Storage

    4MVR5D000.book Page 71 Wednesday, September 26, 2018 4:44 PM 11. STORAGE Proper storage preparation is essential for keeping your brush cutter trouble free and looking good. The following steps will help to keep rust and corrosion from impairing your brush cutter. CAUTION: •...
  • Page 74 4MVR5D000.book Page 72 Wednesday, September 26, 2018 4:44 PM c. Press the priming pump several times until all fuel has returned to the fuel tank. PRIMING PUMP FUEL TANK CAP d. Tip the engine toward the fuel filler neck again to drain the fuel left in the fuel tank into the container.

  • Page 75: Troubleshooting

    Clean, readjust gap and dry the spark plug. Replace it if necessary (see page 62). 5.If the engine still does not start, take the brush cutter to an authorized Honda dealer. When an abnormal vibration occurs during operation, immediately turn off the engine and check the cutting attachment is properly installed and tightened securely, and inspect it for wear, crack or any other damage.

  • Page 76: Specifications

    4MVR5D000.book Page 74 Wednesday, September 26, 2018 4:44 PM 13. SPECIFICATIONS MODEL UMK450T HAPT Power product description code Frame TYPE U2NT UTNT Handle type U-shaped Clutch type Centrifugal clutch Tool Cutting blade Nylon-line Cutter Type 2-tooth blade Tap & Go O.D.
  • Page 77 4MVR5D000.book Page 75 Wednesday, September 26, 2018 4:44 PM Engine MODEL UMK450T Engine model GX50T Engine description code GCCFT Engine type 4-stroke, overhead cam, 1 cylinder Displacement 47.9 cm Bore and Stroke 43.0 x 33.0 mm Engine Net power 1.47 kW/7,000 rpm (in accordance with SAE J1349*) Engine max.

  • Page 78: Warranty Policy

    Brush Cutter free from any manufacturing defect. In the event of failure, any Honda authorised dealer will repair or replace, free of charge, any part of the set as per norms laid down by the company. The company's decision shall be final and binding.

  • Page 79: Installation & Free Service

    15. INSTALLATION AND FREE SERVICES 1. PRE-INSTALLATION CHECK - A pre delivery inspection is provided by Honda Authorised dealer so that you can enjoy longer trouble free Brush Cutter life. - P.D.I. coupon is attached herewith. 2. PERIODIC MAINTENANCE SERVICE - To enhance trouble free Brush Cutter life, periodic maintenance must be carried out as per maintenance schedule given in the owner's manual.

  • Page 80: List Of Area Offices

    16. LIST OF AREA OFFICES -Toll Free 1800112323 A-904, Siddhi Vinayak Tower, B/H DCP Office, Off S.G. Highway, Makarba, Ahmedabad-380051, Gujarat. Tel. : 079-48000730, 9978912986 : 079-29700121 E-mail : ao.ahm@hspp.com Door No.1-8-32/64, Plot No.64, G. Y. R. Plaza, IInd Floor, Bapu Bagh Colony, P.

Table of Contents