Table of Contents
Advertisement
Operation Guide 3220
Stopwatch
The stopwatch lets you measure elapsed time, split times,
Hours
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Seconds
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
1/100 second
elapsed time measurement.
Minutes
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-9).
E-40
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-9).
Hours
Countdown End Beeper
Minutes
The countdown end beeper lets you know when the
Seconds
countdown reaches zero. The beeper stops after about 10
seconds or when you press any button.
E-42
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
Timer start time
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To stop a countdown operation completely, first pause it
(by pressing D), and then press A. This returns the
Current timer
countdown time to its starting value.
time
E-44
• You can use the procedure below to select either 1.5 seconds or 3 seconds as the
illumination duration. When you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
display contents start to flash. This is the setting screen.
2. Press C 10 times until the current illumination duration
setting (
3. Press D to toggle the setting between
(approximately 1.5 seconds) and
3 seconds).
4. Press A to exit the setting screen.
E-46
Warning!
• • • • • Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• • • • • When you are wearing the watch, make sure that its auto light switch is
turned off before riding a bicycle or operating a motorcycle or any other
motor vehicle. Sudden and unintended operation of the auto light switch can
create a distraction, which can result in a traffic accident and serious
personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
• The auto light switch on indicator is on the display in all modes while the auto light
switch is turned on.
E-48
or
) appears.
(approximately
To measure times with the stopwatch
Elapsed Time
D
D
D
➤
➤
Start
Stop
Re-start
Split Time
D
A
A
➤
➤
Start
Split
Split release
(SPL displayed)
Two Finishes
D
A
D
➤
➤
Start
Split
Stop
First runner finishes.
Second runner
Display time of first
finishes.
runner.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" (page
E-44) to display it.
2. Press C to move the flashing between the hour and
minute settings.
3. When a setting is flashing, use D (+) and B (–) to
change it.
• To specify a countdown start time of 24 hours, set
.
4. Press A to exit the setting screen.
Illumination
This watch has an EL (electro-luminescent) panel that
Auto light switch on
causes the entire display to glow for easy reading in the
indicator
dark. The watch's auto light switch turns on illumination
automatically when you angle the watch towards your
face.
The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
See "Illumination Precautions" (page E-72) for other
important information about using illumination.
To illuminate the display manually
In any mode (except when a setting screen is on the
display), press
The above operation turns on illumination regardless of
the current auto light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode. Note that this watch features a "Full Auto
EL Light", so the auto light switch operates only when available light is below a certain
level. It does not turn on the backlight under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
Power Supply
This watch is equipped with a solar cell and a rechargeable battery that is charged by
the electrical power produced by the solar cell. The illustration shown below shows
how you should position the watch for charging.
Example: Orient the watch so its face is
pointing at a light source.
• The illustration shows how to position a
watch with a resin band.
• Note that charging efficiency drops when
any part of the solar cell is blocked by
clothing, etc.
• You should try to keep the watch outside of
your sleeve as much as possible. Charging
is reduced significantly if the face is
covered only partially.
D
A
➤
➤
Stop
Clear
A
D
➤
➤
Stop
Clear
A
A
➤
➤
Split release
Clear
Display time of
second runner.
E-41
E-43
to turn on illumination.
E-45
More than 40°
E-47
Solar cell
E-49
Advertisement
Table of Contents
