Operator’s Manual n a n o WARNING! Read this Operator’s Man- ual carefully before using this tool. Failure to under- stand and follow the con- n a n o tents of this manual may result in electrical shock, Record product serial number below as it appears on the nameplate. fire and/or serious person- Serial al injury.
Work Area Safety ................................3 Electrical Safety ................................3 Personal Safety................................3 Equipment Use and Care .............................3 Service ..................................4 Specific Safety Information ............................4 SeeSnake nanoReel Safety ............................4 Description, Specifications, and Standard Equipment ....................5 Description ...................................5 Specifications ................................5 Standard Equipment ..............................5 nanoReel Components ..............................6 Icon Legend ..................................6...
n a n o Safety Symbols In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safety in- formation. This section is provided to improve understanding of these signal words and symbols. This is the safety alert symbol.
If using drain cleaning equipment at the same performance. time as drain inspection equipment, only wear RIDGID drain cleaning gloves. Never grasp the ro- tating drain cleaning cable with anything else, includ- ing other gloves or a rag which can become wrapped around the cable and cause hand injuries.
Specifications Practice good hygiene. Use hot, soapy water to Table 1 wash hands and other body parts exposed to drain SeeSnake nanoReel Specifications contents after handling or using drain inspection Weight equipment. To prevent contamination from toxic or in- with micro CA-300 fectious material, do not eat or smoke while operating 14.65 lb [6.6 kg]...
n a n o System Cable for micro CA-300 Camera Monitor nanoReel Components micro CA-300 System Cable for Push Cable Guide SeeSnake CCU Case Latch micro CA-300 Case Latch Front Case Connector Plug Cord Wrap Rear Case Feet Feet Slip-Ring Module Camera Head Camera Clip Rear Case...
n a n o Assembly WARNING To reduce the risk of serious injury, properly assem- ble the nanoReel in accordance with these proce- dures. Camera Head Routing 1. Set the unit on a level surface and lay it on its back. 2.
n a n o 4. Unthread the screw. Repeat for each of the remaining three nuts. 5. Position the cord-wrap arm and cradle on the same side of the case, facing in the opposite direction. Make sure the cord-wrap horns point outward. 6.
n a n o Use ball guides whenever possible to reduce wear and Pre-Operation Inspection tear on the camera system. Ball guides can be easily WARNING removed or adjusted to allow for better movement in pipes as needed. For example, placing two ball guides near the front end of the camera may bias the camera head upward to allow better viewing of the top of the pipe during an inspection.
n a n o proof. Electrical connections can cause sparks. Clear, level, stable dry place for machine and operator. Do not use the machine while standing in water. If required, remove the water from the work area. Ensure the nanoReel is stable. Clear path to electrical outlet if used for monitor, that does not contain any potential sources of damage for the power cord.
n a n o NOTICE Operating Instructions Use of the nanoReel camera in porcelain ap- pliances scratch the surface finish of the porcelain. To WARNING avoid scratching, use a curved non-marking pipe segment (such as PVC or ABS pipe) to lead the camera past the por- celain bowl and into the drain.
Page 12
n a n o the top), raise the camera head out of the liquid in the pipe, and help negotiate bends; especially at tight turns such as in a toilet flange (See Figure 17 , Figure 18, and Figure 19). See the “Installing Ball Guides” section in this Operator’s Manual for more information.
Sonde has been located, the LEDs can be returned to normal brightness to continue the inspection. When the nanoReel Sonde is turned ON, a locator such as the RIDGID-SeekTech SR-20, RIDGID-SeekTech SR-60, Scout, or NaviTrack II set to 512 Hz can detect it.
Avoid hosing the contact board on the back of the drum. Accessories WARNING The following RIDGID products have been designed to function with the nanoReel. Other accessories suitable for use with other tools may become haz- ardous when used with the nanoReel. To reduce Figure 23 –...
Dispose of the components in unsafe to operate. compliance with all applicable regulations. Contact your Service and repair of the SeeSnake nanoReel must be local waste management authority for more information. performed at a RIDGID Independent Authorized Service For EC Countries: Do not dispose of Center.
Page 16
Printed in U.S.A. 1.800.544.2843 www.calcert.com sales@calcert.com...