Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Mitsubishi 1540 FD
Summary of Contents for Mitsubishi 1540 FD
- Page 1 Mitsubishi Agricultural Machinery Corporation Owners Manual Mitsubishi 1540 FD...
-
Page 2: Safety Precaution
Any improper handling of this tractor could lead to an accident. Prior to the operation of the tractor, be sure to read the Instruction Manual carefully and have a thorough understanding of the description. In particular, the instructions given in “Safety Precautions” must be strictly followed. SAFETY PRECAUTION When running the tractor at high speed or on roads, make sure the right and left brake pedals •... - Page 3 Introduction This instruction manual contains information on the operation, lubrication and maintenance of your tractor. The information contained is comprehensive and essential, and is designed to assist you, even if un-experienced, in utilizing your tractor. How well your tractor continues to give satisfactory performance depends greatly upon the mannor in which it is operated.
- Page 4 CONTENTS...
-
Page 5: Section 1. Operation
Section 1. Operation Starting and stopping the engine Before starting the engine, be sure to check the following points. 1. Confirm that the fuel tank is filled with sufficient fuel. 2. Check the amount of oil in the engine and transmission. 3. -
Page 6: Starting In Cold Weather
STARTING IN COLD WEATHER 1. The fuel injection pump of this engine adopts the mechanism to ensure easier engine starting by excessive injection of fuel when the throttle lever is fully pulled. 2. To start the engine specially in cold weather fully pull the throttle lever, heat the glow plug enough and crank the engine. -
Page 7: Water Temperature Warning Lamp
BATTERY CHARGE WARNING LAMP When the starter switch is set to “ON” position, the battery charge warning lamp glows red. When the battery is being charged normally while the engine is running, the lamp turns off. If the lamp continues to glow, stop the engine and check the alternator, regulator, and cabling. -
Page 8: Glow Signal
GLOW SIGNAL The glow signal which indicates the heating state of the glow plug in the combustion chamber is installed on the instrument panel. It is easily seen from the heating condition of the glow signal resistance wire.. THROTTLE LEVER When the throttle lever is pulled fully tward the operator, the engine speed reaches the maximum of 2,900 rpm. -
Page 9: Parking Brake
revolutions, depress the clutch pedal and then the brake pedal To shorten the braking distance, lower the engine revolutions quickly, depress the brake pedal and then the clutch pedal just before the engine stops. For turning in a confined space the right and left axles can be braked independently by turning to the left the locking plate interlocking the left and right brake pedals. -
Page 10: Power Take-Off
The differential lock is automatically released by the force of the spring when you put your right foot off the pedal. However, under particular conditions, there may be occasions where the lock does not release. When this occours, depress the right and left brake pedals alternately and quickly until the lock is released. -
Page 11: Operator's Seat
4. Lubricate the PTO shaft well. 5. Avoiding using a square-shaped drive shaft as much as possible. 6. Special care should be given to the yoke position so that the driven shaft is well balanced. POWER TAKE OFF The 4-Wheed Drive shift lever is located on the right side of the clutch housing and it should be operated in a similar manner to that for the shift, sub shift, and PTO Shift levers. -
Page 12: Ballast Weight
CAUTION: 1. Avoid widening front tread of the 4-wheel drive tractor by switching the right and left front tires as this may cause serious troubles on the steering linkage. 2. Check at frequent intervals to make sure the front wheel is tightened securely to specified torque and that the axle housing and gear case are secured to each other to the specified torque. -
Page 13: Three Point Linkage
Rear 2 & 4-WD 8-16 1.6kg/cm⁴(22.8psi) TR-15 Front 2-WD 18x7.00-8 1.0kg/cm⁴(14.22psi) TR-413 6-12 TR-13 Front 4-WD 1.0kg/cm⁴(14.22psi) Rear 2 & 4-WD 9.5-16 1.4kg/cm⁴(19.9psi) TR-15 NOTE: Air pressure of the tires must be checked according to the loading weight on the tires. For more details, please call and talk with the local dealer. -
Page 14: Flow Control Valve
HOLD When the implement is fully moved up, the control valve is placed in neutral position while the implement is moving up or down. The implement can be held in any desired position. FLOW CONTROL VALVE The flow control knob which controls the lowering speed of the implement is located in front of the hydraulic case under the seat. - Page 15 NOTE: the hydraulic control lever wil not return to “Neutral” automatically, so the control lever must be returned manually to Neutral when the implement reaches a maximum height. If the control lever is left in the “Lift” the relief valve starts operation and the temperature of the hydraulic oil rises thus causing trouble to the machine.
-
Page 16: Section 2. Regular Maintenance
Section 2. Regular Maintenance To keep your tractor operating in the top condition and insure its proper performance and reliability for a long period of time, periodic inspection is indispensable. If your tractor is not periodically serviced, the results will be such that it’s performance and operating life will be reduced. -
Page 17: Section 3. Service Information
Section 3. Service Information... -
Page 18: Section 4. Storing
Section 4. Storing... -
Page 19: Section 5. Specifications And Data
Section 5. Specifications and Data Engine (Mitsubishi Diesel Engine) Model…………………………………………………. Type…………………………………………………….. Water Cooled vertical 4 cycle overhead valve in line diesel engine Number of cylinders……………………………. Piston Displacement……………………………. 849 cc (51.7 cu. In.) Bore x Stroke………………………………………. 68 X 78 mm (2.67 x 3.07 in.) Max. -
Page 20: Fuel System
Belt length and size Size “A” 37.25” long Granger 3L370 NAPA NBH 257370 Belt Angle : 36 Belt Imperial Length : 37.56" (954 mm) Belt Top Width : .41" (10 mm) Fuel System Fuel ………………………………………………….. Wax Type (if installed) Fuel Injection Pump …….…………………… 0.6 kg/cm2 (8.5 psi) Injection nozzle ………….…………………….. -
Page 21: Chassis Dimension
J S 0 9 9 F O R E N G I N E M O D E L M I T S U B I S H I K 3 A K 3 B K 3 D K 3 E 1 2 V 1 . - Page 22 Worm and sector type (4-WD)……….………………… Ball screw type Toe-in (2WD & 4WD)……………………….. 6mm +_ 2mm (5/32in ~10/32in) Hydraulic System (Mitsubishi live hydraulic system) Control ...……………………………………………. Lift, hold, down, flow control and lift lock Type of cylinder .……………………………….. Single acting cylinder...
-
Page 23: Point Linkage
Diameter of piston ……………………………. 60 mm (2.36 in) Stroke of Piston …….…………..………………. 71 mm(2.8 in.) Pressure relief valve……………………………. 135 kg/cm2 (1,920 psi) Pump model ………………………………………. 18 Hp @ 2,700 rpm Type of hydraulic pump ……………………… Pressure loading type Output of hydraulic pump …………………… 13.8 L (3.6 gal) per min at 2,900 engine rpm (5.27 cc/rev design output) Implement lock valve …………………………. - Page 24 [1.3kph] 0.82mph [2.0kph] 1.24mph [3.7kph] 2.30mph [5.8kph] 3.61mph [8.8kph] 5.47mph MAX H6 [16.3kph] 10.14mph [1.7kph] 1.05mph [7.4kph] 4.61mph Capacities Engine Oil 5L (5.3 QT.) Fuel Tank 18 L (4.7 GAL.) Transmission Case Oil 12 L (21.2 QT.) Steering Gear Case Oil 0.3L (0.64 Pint) Hydraulic Oil Same as Transmission Oil...