Related Manuals for LG HG6412A
Summary of Contents for LG HG6412A
- Page 1 Installation and Operating Instructions Built in Gas Cooktops Model Numbers HG6412A HG7512A HG9512A Please note:This cooktop must be installed by an authorised installer. P/No. :MFL30298504...
-
Page 3: Table Of Contents
CONTENTS OPERATING INSTRUCTIONS SAFETY PRECAUTIONS PAGE 3 COOKTOP IDENTIFICATION PAGE 4 LIGHTING THE GAS BURNERS PAGE 5 USING THE GAS COOKTOP PAGE 6 COOKTOP INSTALLATION PAGE 7 CONVERSION TO DIFFERENT TYPES OF GAS PAGE 9 CLEANING PAGE 9 GAS CONSUMPTION AND INJECTOR SIZES PAGE 10 DIAGRAMS PAGE 11... -
Page 5: Safety Precautions
• Do not try to modify the appliance. In the case of faults, do not attempt repair but ask for assistance from a LG Service Agent. • The data plate with its technical data is in a visible position under the housing. There is another data plate enclosed that should be attached to a handy surface for future reference. -
Page 6: Cooktop Identification
This booklet covers a number of models. You can see your model number on the data plate: MODELS 60cm hob with front commands Mod: HG6412A (Fig. 1) 1. Semi-rapid front burner (SR) 2. Semi-rapid back burner (SR) 3. Auxiliary burner (A) 4. -
Page 7: Lighting The Gas Burners
LIGHTING THE GAS BURNERS Gas burners The flow of gas to the burners is regulated by the controls knobs. Depending on the model, the graphic symbols are printed on the knobs or the control panel (Fig. 6). The indicator symbols are: Valve closed, no gas flow Maximum capacity, maximum gas flow Minimum capacity, minimum gas flow... -
Page 8: Using The Gas Cooktop
USING THE GAS COOKTOP Pan supports (trivets) The trivets were designed to make the cooktop easy and safe to use. We recommend checking their exact position and stability on the cooktop before each use. Furthermore, check that the supporting rubbers are integral and correctly positioned. Small vessel support (Fig. -
Page 9: Cooktop Installation
COOKTOP INSTALLATION INSTRUCTIONS Installation on the kitchen bench The cooktop can be installed on materials as long as they are heat-resistant (minimum temperature 100°C). Clearances from combustable surfaces must be 120mm all around to comply with AS5601 regulations. The size of the hole to be cut into the kitchen bench and the minimum distance between the back, side and overhead walls are shown in figures 7, 8, and 9. - Page 10 The instructions are for a qualified installer. The appliance must be installed correctly, conforming to the laws in force. Remove the electrical power supply before servicing the appliance. GAS COOKTOP INSTALLATION Connecting the gas These technical instructions have been prepared for the use by Authorised persons. The requirements of the local Gas and Electrical authorities must be adhered to, consult AG601/AS5601 as appropriate.
-
Page 11: Conversion To Different Types Of Gas
CONVERSION TO DIFFERENT TYPES OF GAS Should the cooktop need to be converted to a gas different to the one it was intended for, the injectors have to be replaced. The injectors are to be installed according to the table on the underside of the cooktop. Injectors can be identified by the diameter expressed in hundredths of mm printed on the injector itself. -
Page 12: Gas Consumption And Injector Sizes
2.75 Wok Burner 1.70 14.0 0.97 13.0 2.75 Large Burner 1.40 10.0 0.90 11.0 2.75 Medium Burner 1.10 0.69 2.75 Small Burner 0.90 0.53 2.75 HG6412A (60 cm) 30.8 31.4 HG7512A (70 cm) 40.2 41.6 HG9512A (90 cm) 42.7 43.6... -
Page 13: Diagrams
DIAGRAMS Fig. 1 Fig. 2... - Page 14 Fig. 3 Fig. 4 Fig. 5 Fig. 6...
- Page 15 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11...
- Page 16 Fig. 12 Fig. 13 Fig. 15 Fig. 14...
- Page 20 H01A375G...