Table of Contents
Advertisement
Quick Links
Important Information: These instructions must be kept with
the product at all times. This product is a prescribed Medical
Device. To be used only under the guidance of a Therapist
or Prescribing Practitioner. You must read these instructions
carefully before use.
INSTRUCTION FOR USE
Dreama
Version 010
Advertisement
Table of Contents
Summary of Contents for Jenx Dreama
- Page 1 Version 010 INSTRUCTION FOR USE Dreama Important Information: These instructions must be kept with the product at all times. This product is a prescribed Medical Device. To be used only under the guidance of a Therapist or Prescribing Practitioner. You must read these instructions...
- Page 2 INSTRUCTION FOR USE Dreama Note: Some fabric and plastic colours may vary, adjustments are not affected.
-
Page 3: Table Of Contents
Contents General Information Optional Components Safety Labels ............7 Glide Lock Accessories ......... 17 Care & Cleaning Instructions ......... 8 Locking Stop Accessories ........18 Maintenance ............9 Accessories ............19 Product Induction & Hand Over ......10 Maintenance & Inspection Specification &... - Page 4 Do not use this product if you suspect or know that it is broken or faulty. Please contact Jenx Limited immediately for advice: Jenx Limited, Tel: +44 (0)114 285 3376.
- Page 5 Dreama Key to Components Swiss clip T-Nut Wing knob Allen key bolt Wing nut Star knob Plastic spacer Plastic washer Key for Users Carers and Re-issue Professional and home users and stores technical users Scallop wheel jenx.com...
-
Page 6: General Information
CHAPTER ONE General Information Carers and Re-issue Professional and home users and stores technical users... -
Page 7: Safety Labels
(see picture), which is located on the product. Please quote this number on all correspondence. Product Labels Each Jenx product has a number of pictorial safety labels attached, these refer to the explanations below. Client weight Limit (chang- es per model and size) Attention/ Warning... -
Page 8: Care & Cleaning Instructions
Wooden Products and Parts • For deep cleaning a low pressure steam cleaner can be used • Do not use organic solvents to clean Jenx Products • Soap and water or antibacterial spray can be used • Check for breaks or splintering of the wood before re-issuing • ... -
Page 9: Maintenance
Unauthorised accessories may affect the safety of this product and invalidate your warranty • Check that gas spring levers are not bent. Do not use the product if any levers are bent. Contact Jenx Limited to arrange replacement Monthly Checks... -
Page 10: Product Induction & Hand Over
If the product is to be re delivered, ensure adequate and secure packaging is used • If in any doubt as to the safety of this product do not issue it, contact Jenx Limited for advice • Products must only be issued fully assembled, clean and in good working order. Instruction for Use must be with the product Jenx Limited offer Technical User Courses for stores personnel. -
Page 11: Specification & Warranty
Dreama Specification & Warranty Description Cot (mm) Bed (mm) Width Length 1200 1900 Height (including base) Individual cushion width (single) Individual cushion width (double) Individual cushion height Individual cushion length No of single cushions supplied No of double cushions supplied Warranty The Instruction for Use of this product should be followed carefully. -
Page 12: Assembly
General Information Assembly 1. Unroll the aluminium base carefully on top of the exist- ing bed base or mattress. 2. Fasten the aluminium base to the bed using the anchor straps. Pass the strap through the white link* nearest to you and thread it through the link on the opposite side of the bed. -
Page 13: Frequent Adjustments
CHAPTER TWO Frequent Adjustments Carers and Re-issue Professional and home users and stores technical users... -
Page 14: Mattress Units
Frequent Adjustments Mattress Units Inserting the mattress units Single mattress unit Double mattress unit Double mattress unit used at each end Push the plastic clip into the link at one end Push the plastic clip into the link at the other end The image above shows the clip securely located into the link Removing the mattress units... -
Page 15: Fitting & Removing Covers
Dreama Fitting & Removing Covers Note: Wash sheets before use Sheets fit as shown above, in the same way as a standard fitted sheet Note: Do not hook the cover over the clip. As shown opposite Correct Incorrect jenx.com... -
Page 16: Optional Components
CHAPTER THREE Optional Components Carers and Re-issue Professional and home users and stores technical users... -
Page 17: Glide Lock Accessories
Dreama Glide Lock Accessories Fitting the glide lock accessories Insert the glide lock end into the alu- minium base of the bed, between two of the sections of mattress, as shown above. Adjusting the glide lock accessories: Position 1: To move backwards, tip the pad forwards 2. -
Page 18: Locking Stop Accessories
Optional Components Locking Stop Accessories Fitting the locking stops and locking stop Accessories 1. Slide Locking stops in from the end of the channel, as shown left. 2. Locking stops can also be dropped sideways into the channel and turned to locate 3. -
Page 19: Accessories
Dreama Accessories Positioning Pads The positioning pads are glide lock accessory and are fitted as described on page 17. They can also be used along with locking feet, as shown on page Why? Benefits of the Adjustments: Positioning pads are used to hold the client in the... - Page 20 Optional Components Accessories Footplates (angle adjustable) The angle adjustable foot supports use the glide-lock post and rotating head system, as explained on page 17. They can be used in conjunction with locking feet as explained on page 18. WHY? The foot support allows the correct therapeutic position for the feet to be achieved and offers support for the feet in the chosen position.
- Page 21 Dreama Accessories Side Lying Platform: Fitting Step 1: Insert four positioning pads as shown Step 2: Position the side lying leg platform on top opposite, these will form the base for the side of the pads. There is a webbing strap with a lock- lying platform ing foot on each corner of the board.
- Page 22 Optional Components Accessories T-Roll (height adjustable) Head of the bed Use the snap buckles on the side to secure the client’s leg to the T-Roll. Locking feet are attached to the T-Roll with snap You can lengthen the straps to give the client buckles.
- Page 23 Dreama Accessories The height of the horizontal supports can be individually altered. You can use 0, 1, 2 or 3 foam blocks on each side. Unclip buckle Loosen strap Remove or replace foam blocks as Push the side post as shown to...
- Page 24 CHAPTER FOUR Maintenance & Inspection Carers and Re-issue Professional and home users and stores technical users...
-
Page 25: Maintenance & Inspection
& Inspection Each Jenx product must be checked and inspected in line with the advice given in this IFU. Failure to com- plete these regular checks poses a risk to the user. Every year, each product must be thoroughly inspected by a person competent to assess faults and able to rectify or out source rectification. - Page 26 If there is any doubt about the safety of the product, do not hesitate to contact our Customer Support Department for advice Products should be thoroughly decontaminated in line with MHRA and local guidelines prior to inspection, storage and re-issue Jenx Limited can take no responsibility for re-issue of products...
-
Page 27: Frequently Asked Questions
The purchasing authority has a duty under the MHRA guidelines DB2006 (05) to address training for Medical Devices Management. Check with your authority. Question: Does Jenx run technical competency courses? Answer: Yes. Please visit jenx.com for details of available courses. Question: Why does my tilt-in-space lever not work? Answer: If your lever does not operate properly, ensure that it is fully unlocked and try again. - Page 28 Seating Standing Sleeping Therapy Mobility Bathroom Jenx Limited, Wardsend Road, Sheffield S6 1RQ T: 0114 285 3376 E: sales@jenx.com jenx.com...