Page 1 LFD DISPLAY User Manual DB32D DB40D DB48D DB55D The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Recommended hours of use per day of this product is under 16 hours.
Page 2 Table of contents Before Using the Product Using MDC Screen Adjustment » Copyright » MDC Programme Installation/Uninstallation » Picture Mode » Safety Precautions » Connecting to MDC » Backlight / Contrast / Brightness / Sharpness / Colour / Tint (G/R) »...
Page 3 » General » Network Status » Reset System » Network Settings Troubleshooting Guide » Wi-Fi Direct » Requirements Before Contacting Samsung » Multimedia Device Settings Support Customer Service Centre » Server Network Settings » Q & A » Device Name »...
Page 4 Table of contents Appendix » Responsibility for the Pay Service (Cost to Customers) » WEEE » Optimum Picture Quality and Afterimage Burn-in Prevention » Licence » Terminology...
Page 5: Before Using The Product
© 2014 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Page 6: Safety Precautions
Safety Precautions Cleaning ― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ― Take the following steps when cleaning. Caution ― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Page 7: Electricity And Safety
Storage Connect the power plug to a grounded power socket (type 1 insulated devices only). Due to the characteristics of high-glossy products, using a UV humidifier nearby may create • An electric shock or injury may result. white-coloured stains on the product. ―...
Page 8: Installation
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. • A fire may result. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. • A fire or electric shock may result.
Page 9 SAMSUNG • Be sure to consult Samsung Customer Service Centre if you want to install the product at such a place.
Page 10: Operation
If the product is dropped or the outer case is damaged, turn off the power Do not lift or move the product by pulling the power cord or any cable. switch and disconnect the power cord. Then contact Samsung Customer Service Centre.
Page 11 • Your eyesight may deteriorate. when water or other foreign substances have entered the product. Then contact Samsung Customer Service Centre. • Product failure, an electric shock or fire may result. Do not hold the product upside-down or move it by holding the stand.
Page 12 Rest your eyes for more than 5 minutes for every 1 hour of product use. Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that •...
Page 13: Checking The Components
Preparations Checking the Components Components ― Components may differ in different locations. - Contact the vendor where you purchased the product if any components are missing. - The appearance of the components and items sold separately may differ from the Warranty card image shown.
Page 14 Items sold separately - The following items can be purchased at your nearest retailer. Wall-mount Kit Stand RS232C-Stereo cable DVI cable HDMI-DVI cable HDMI cable Video cable Stereo cable Component cable RCA stereo cable - The RS232C adapter can be used to connect to another monitor using the D-SUB (9-pin) type RS232C cable.
Page 15: Control Panel
Parts ― The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Panel Key Control Panel Buttons Description Power on the product. If you press the button when the product is turned on, the control menu will be displayed.
Page 16 Buttons Description ― If you press the button on the panel key when the product is turned on, the control menu will be displayed. Select the connected input source. Control menu Move the panel key right to select Source in the control menu. When the list of Source input sources is displayed, move the panel key left or right to select the desired input source.
Page 17: Reverse Side
Port Description Reverse Side RS232C IN Connects to MDC using an RS232C adapter. ― The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. RS232C OUT RGB / DVI / HDMI / AV / Receives sound from a PC via an audio cable.
Page 18: Anti-Theft Lock
Anti-theft Lock Spacer logo ― An anti-theft lock allows you to use the product securely even in public places. Do not pull on the spacer logo using force. The logo may tear or break off. ― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
Page 19: Remote Control
Remote Control ― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. ― A button without a description in the image below is not supported on the product. POWER Power off the product.
Page 20 Display information about the current input TOOLS INFO Quickly select frequently used functions. source. Move to the upper, lower, left or right menu, or adjust an option's setting. Confirm a menu selection. Exit the current menu. RETURN EXIT Return to the previous menu. Manually select a connected input source from HDMI or HDMI.
Page 21: Tilting Angle And Rotation
Tilting Angle and Rotation 15 ˚ ― Contact Samsung Customer Service Centre for further details. • The product can be tilted at a maximum angle of 15 from a perpendicular wall surface. • To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Page 22 Figure 1.3 Side view Installation on an Indented Wall ― Contact Samsung Customer Service Centre for further details. Plane view Minimum 40 mm Minimum 70 mm Minimum 50 mm Minimum 50 mm Ambient temperature: Under 35 C ― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.
Page 23: Using The Cover-Jack
Using the COVER-JACK To prevent theft of the SD memory card or any other USB device, install the COVER-JACK. ― When using a DVI cable, make sure to cut off the side of the COVER-JACK first. ― Cut out the Cover-Jack according to the DVI cable size before use.
Page 24: Installing The Wall Mount Kit
We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
Page 25 Unit: mm Model name VESA screw hole Standard Screw Quantity specs (A * B) in millimeters DB32D 200 × 200 DB40D M8 / L 14~16 DB48D 400 × 400 DB55D ― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
Page 26: Remote Control (Rs232C)
Remote Control (RS232C) • Pin assignment 1 2 3 4 5 Cable Connection RS232C Cable Interface RS232C (9 pins) 6 7 8 9 TxD (No.2), RxD (No.3), GND (No.5) Signal Bit rate 9600 bps Detect data carrier Data bits 8 bit Received data Parity None...
Page 27 LAN Cable • RS232C cable Connector: 9-Pin D-Sub to Stereo Cable • Pin assignment 1 2 3 4 5 6 7 8 -P2- -P1- -P1- -P1- -P2- -P2- Female --------> STEREO <-------- PLUG Pin No Standard Colour Signal ---------- (3.5ø) White and orange Orange White and green...
Page 28 Cross LAN cable (PC to PC) • Connector : RJ45 Direct LAN cable (PC to HUB) RJ45 RJ45 RJ45 MDC Signal Signal <--------> <--------> Signal Signal <--------> <--------> <--------> <--------> <--------> <-------->...
Page 29 Connection • Connection 2 • Connection 1 RJ45 RJ45 RS232C RS232C RS232C RS232C • Connection 3 RJ45 RS232C RS232C RS232C RS232C...
Page 30: Control Codes
Command type Command Value range Control Codes Video Wall On 0x84 Viewing control state (Get control command) Video Wall User Control 0x89 Header Command Data length Checksum • All communications take place in hexadecimals. The checksum is calculated by adding up all 0xAA Command type values except the header.
Page 31 Power control Volume control • Function • Function A product can be powered on and off using a PC. The volume of a product can be adjusted using a PC. • Viewing power state (Get Power ON / OFF Status) •...
Page 32 Input source control 0x24 HDMI2_PC • Function 0x25 DisplayPort The input source of a product can be changed using a PC. ― DVI_video, HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to • Viewing input source state (Get Input Source Status) "Get"...
Page 33 Screen mode control • Nak Header Command Data length Ack/Nak r-CMD Val1 Checksum • Function The screen mode of a product can be changed using a PC. 0xAA 0xFF 0x18 "ERR" Video Wall Screen mode cannot be controlled when the function is enabled.
Page 34 PIP On/Off control Auto adjustment control (PC and BNC only) • Function • Function The PIP mode of a product can be turned on or off using a PC. Automatically adjust the PC system screen using a PC. ― Only available on models that have the PIP function. •...
Page 35 Video Wall Mode Control Safety Lock • Function • Function Video Wall mode can be activated on a product using a PC. PC can be used to turn the Safety Lock function on or off on a product. Video Wall This control is only available on a product whose is enabled.
Page 36 Video Wall On • Nak Header Command Data length Ack/Nak r-CMD Val1 Checksum • Function Turn Video Wall on or off on the product from your computer. 0xAA 0xFF 0x84 • Get Video Wall On/Off Status "ERR": A code showing what error has occurred Header Command Data length...
Page 37 10x10 Video Wall Model 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x1F 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x2F 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28...
Page 38 Wall_SNo: Product Number code assigned to the product 10x10 Video Wall Model : ( 1 ~ 100) Set Number Data 0x01 0x02 0x63 0x64 • Ack Header Command Data length Ack/Nak r-CMD Val1 Val2 Checksum 0xAA 0xFF 0x89 Wall_Div Wall_SNo •...
Page 39: Connecting And Using A Source Device
Connecting and Using a Source Device Before Connecting Connecting to a PC • Do not connect the power cable before connecting all other cables. Pre-connection Checkpoints Ensure you connect a source device first before connecting the power cable. • A PC can be connected to the product in a variety of ways. ―...
Page 40: Connection Using A Dvi Cable (Digital Type)
Connection using a DVI cable (digital type) Connection using an HDMI-DVI Cable ― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name DVI PC to access video and audio content stored on the PC. DVI IN / MAGICINFO IN HDMI IN...
Page 41: Connection Using An Hdmi Cable
Connection using an HDMI Cable HDMI IN...
Page 42: Connecting To A Video Device
Connecting to a Video Device • Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. • You can connect a video device to the product using a cable. ―...
Page 43 Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable ― Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To Using an HDMI cable or HDMI to DVI Cable (up to 1080p) resolve this, additionally connect an audio cable to the audio ports on the product and video device.
Page 44: Connecting To An Audio System
Connecting to an Audio System Connecting the LAN Cable ― Connecting parts may differ in different products. ― Connecting parts may differ in different products. RJ45 AUDIO OUT • Use Cat7(*STP Type) cable for the connection. *Shielded Twist Pair...
Page 45: Connecting The Network Box (Sold Separately)
Connecting the network box (Sold separately) ― For details on how to connect to a network box, refer to the user's manual provided with the network box upon purchase. MagicInfo To use MagicInfo, a network box (sold separately) must be connected to the product. ―...
Page 46 Enter the IP information. Select a display mode. MagicInfo Setup Wizard - v.1.12 MagicInfo Setup Wizard - v.1.12 Select TCP/IP - step 2 Select Screen Type - step 4 Obtain an IP address automatically Use the following IP address: Landscape IP address: 192 .
Page 47: Changing The Input Source
Changing the Input source Source allows you to select a variety of sources and change source device names. You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.
Page 48: Using Mdc
Using MDC Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme can be downloaded from the website. MDC Programme Installation/Uninstallation In the displayed "Ready to Install the...
Page 49: Connecting To Mdc
Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor. Monitor 1 RS232C IN RS232C OUT Monitor 2 Computer...
Page 50: Using Mdc Via Ethernet
Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. Display devices can be connected to each other using a LAN cable. Connection using a direct LAN cable ― Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB. Monitor 1 RJ45 Monitor 2...
Page 51 Connection using a cross LAN cable ― Multiple products can be connected using the RS232C IN / OUT port on the product. Monitor 1 RJ45 RS232C OUT Monitor 2 Computer...
Page 52: Home Feature
Home feature → This feature is provided in Support Go to Home. Accessible using the HOME button on the remote control. Player ― To use the Player feature, set Play via MagicInfo in System. Play a range of content such as channels with schedules assigned, templates or files. Play channels or content using any of the following methods.
Page 53: Approving A Connected Device From The Server
Approving a connected device from the server Select Device from the top menu bar. • Set MagicInfo Mode MagicInfo Server Network Settings. Approve and use the MagicInfo server now. ― First configure the server Network Settings before device approval. Access the server you have assigned to your device. Select MagicInfo from the menus on the left.
Page 54 Enter the information required to approve the device. When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. ― For further details on how to configure a schedule, refer to the <MagicInfo Server user's manual>.
Page 55: Network Channel
Network Channel Device:Internal Contents: All Sort by: File Name Options Player 1 / 2 item(s) Browse and play content stored on the selected device. Play content, templates and schedules configured on the server. Player • You can view whether the server is connected (approval) in the menu screen.
Page 56: Available Features In The Player Page
Available features in the Player page Player list page provides the following features. Device • Select either Internal to search for a desired device list. Internal Contents • Select a content type as criterion to search for a desired content list. Video Image Flash...
Page 57: Player Page Settings Menu
Player page Settings menu Aspect Ratio Aspect Ratio Original or Full. to either Settings Full Original • ― This feature is only available for Videos, Images, Office files. Settings Display Duration Set whether to display content in the original aspect ratio or in full Set the duration for each page in a slideshow.
Page 58: When Content Is Running
When Content is Running Press the INFO button on the remote control. Type : Type of channel currently playing • ― Only applicable during Network Channel Local Channel playback. Viewing the details of the content that is running Number: Number assigned to the channel currently playing •...
Page 59 Changing the settings for the content that is running Press the TOOLS button on the remote control during content playback to configure settings such as Picture Mode Sound Mode. Playlist • View a list of content items currently playing. Music •...
Page 60: File Formats Compatible With Player
File Formats Compatible with Player Template files and LFD(.lfd) files • Supported file systems include FAT32 and NTFS. Restrictions • A file with a vertical and horizontal resolution larger than the maximum resolution cannot be • Ensure a distributed folder (content / schedules) exists in Internal memory.
Page 61 Contents File Extension Container Video Codec Resolution Frame rate Bit rate Audio Codec (fps) (Mbps) *.avi DivX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf MPEG4 SP / ASP *.wmv HE-AAC *.mp4 *.mov H.264 BP / MP / HP *.3gp MPEG(MP3) *.vro...
Page 62 Video Audio Image • 3D video is not supported. • Audio content with a Bit rate or Frame rate • Compatible image file format : Jpeg larger than the rate specified in the table above • Content with a resolution larger than the •...
Page 63 Flash Power Point • Compatible with Flash 10.1 • Compatible document file formats • Compatible document file formats • Flash Animation - Extension : ppt, pptx - Extension : pdf - Compatible file format : SWF - Version : Office 97 ~ Office 2007 •...
Page 64: Template Files
WORD Template files Network Channel Local • Compatible document file formats • Creation/editing/playback are only available in • Supported in Template. Channel - Extension : .doc, .docx - Version : Office 97 ~ Office 2007 • Compatible document file formats - Extension : .lfd •...
Page 65 File Formats Compatible with Video Wall ― Refer to the <MagicInfo Server user's manual> for further details. Video Image • 3D video is not supported. • Compatible image file format : Jpeg, png, bmp • Content with a resolution larger than the resolution specified in the table •...
Page 66 Restrictions • Only one video (Videos) file can be played per client. ― Different content files can be played on the displays of a video wall. Two video (Videos) files cannot be played on a single display of a video wall. Available Not available Available...
Page 67: Available Features In The Schedule Page
Schedule Available features in the Schedule page Schedule page provides the following features. HOME → Schedule → ENTER E Type • - Local: Add or edit schedules. - Network: View the network schedule configured on the server. Schedule Type : Local Device : Internal Options Device...
Page 68 Configuring channel schedules Play media content such as videos, photos and music at a desired time. Select a channel to configure. Select video, music and photo content you want to apply to the channel schedule. Set the time to play the schedule. (Start Time Stop Time)
Page 69 Template Available features in the Template page Create unique content using templates. It is easy to create content. Simply change images and text in a template. HOME → Template → ENTER E Sort the template list using the following criteria. Market •...
Page 70 Inserting content such as videos, photos and PDF files Organize a template by inserting text, video, photo, or PDF files as desired. Entering text Template Select in the editable zone to add content or edit the existing text. Edit Item(s) selected Template Select in the editable zone to add content or edit the existing text.
Page 71 Preview Configure Template Name and Storage. Save Duration 23:59:59 Template Name Template1 Template preview is running. It will stop Storage Internal after 20 seconds. Save Cancel New town interior design Save Press the button to finish creating the content. Sustainble evolution unfolods tomorrw’s design Preview the created template using the Preview feature.
Page 72: Clone Product
Clone Product Export the product settings to a USB device or load the settings via a USB device. This option is useful when assigning the same settings to several products. When USB does not contain a duplicate file HOME → Clone Product →...
Page 73: Pc Connection Cable
ID Settings Assign an ID to a set. Press u/d to select a number, and press E. HOME → ID Settings → ENTER E Device ID Enter the ID number of the product connected to the input cable for input signal reception. (Range: 0~224) ―...
Page 74: Video Wall
Customize the layout of multiple displays that are connected to form a video wall. Video Wall In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo function.
Page 75 Format Select how to display images on the videowall display. • Full: Display images in full screen with no margin. • Natural: Display images in the original aspect ratio without enlarging or reducing the size. ― The Format Video Wall is set to On.
Page 76: Picture Mode
- To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness, color, gamma and uniformity, using the color calibration program Advanced Color Management. - To download the Advanced Color Management program, visit www.samsung.com/displaysolutions.
Page 77: On/Off Timer
On/Off Timer ― You must set the clock before you can use On/Off Timer. On Timer HOME → On/Off Timer → ENTER E On Timer so that your product turns on automatically at a time and on a day of your choosing. The power is turned on with the specified volume or input source.
Page 78: Off Timer
Off Timer Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 Off Timer • Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the days you want Off Timer to turn off your product.
Page 79: More Settings
Ticker Input text while a video or image is displayed and display the text on the screen. • • Message: Enter a message to display on the screen. → → ENTER E HOME Ticker • Time: Set the Start Time End Time to display a Message.
Page 80: Url Launcher
URL Launcher For details on how to use the URL Launcher feature, contact the dealer the product was purchased from. ― To use the URL Launcher Play via URL Launcher in System. feature, set HOME → URL Launcher → ENTER E Change URL 12:00 URL Launcher...
Page 81: Screen Adjustment
Advanced Colour Management. · Tint (G/R) - To download the Advanced Colour Management programme, visit www.samsung.com/displaysolutions. - The displayed image may differ depending on the model.
Page 82: Backlight / Contrast / Brightness / Sharpness / Colour / Tint (G/R)
Backlight / Contrast / Brightness / Your product has several options for adjusting picture quality. Picture Mode Picture Mode settings Adjustable options Sharpness / Colour / Tint (G/R) Shops & Malls, Offices & Schools, Videos/Images Backlight Contrast Brightness Sharpness Terminals & Stations, Video Wall Colour...
Page 83: Colour Temperature
Colour Temperature Adjust the colour temperature (Red / Green / Blue). (Range: 2800K–16000K) ― If Colour Tone is set to Off, Colour Temperature is disabled. ― If Picture Mode is set to Calibration, Colour Temperature is disabled. MENU m → Picture →...
Page 84: White Balance
White Balance 2 Point Adjust the colour temperature for a more natural picture. MENU m → Picture → White Balance → ENTER E R-Offset G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness. • R-Gain G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness. •...
Page 85: Calibrated Value
Don't apply Apply • MENU m → Picture → Calibrated value → ENTER E ― To download the Advanced Colour Management programme, visit www.samsung.com/displaysolutions. ― If Picture Mode is set to Calibration, Calibrated value is disabled. Picture Calibrated value - The displayed image may differ depending on the model.
Page 86: Advanced Settings
Advanced Settings Picture Mode Picture Mode settings Adjustable options Shops & Malls, Offices & Schools, Videos/Images Dynamic Contrast Black Tone Flesh Tone Video Wall RGB Only Mode Colour Space MENU m → Picture → Advanced Settings → ENTER E Text Dynamic Contrast Black Tone Advanced Settings...
Page 87: Dynamic Contrast
Dynamic Contrast Advanced Settings Adjust the screen contrast. Dynamic Contrast Medium Medium High • Black Tone Darker Black Tone Flesh Tone Select the black level to adjust the screen depth. RGB Only Mode Dark Darker Darkest • Colour Space Native Flesh Tone Motion Lighting Flesh...
Page 88: Picture Options
Picture Options Picture Mode Picture Mode settings Adjustable options Shops & Malls, Offices & Schools, Videos/Images Colour Tone Digital Clean View MPEG Terminals & Stations, Video Wall Noise Filter HDMI Black Level Film Mode MENU m → Picture → Picture Options →...
Page 89: Colour Tone
Colour Tone Picture Options If the input source is PC, HDMI (PC connection). Colour Tone Cool Standard Warm • If the input source is AV, Component or HDMI. Digital Clean View Cool Standard Warm1 Warm2 • MPEG Noise Filter ― If Picture Mode is set to Calibration, Colour Tone...
Page 90: Hdmi Black Level
HDMI Black Level Picture Options Selects the black level on the screen to adjust the screen depth. Colour Tone Normal • ― Available only in HDMI mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p). Digital Clean View MPEG Noise Filter Film Mode HDMI Black Level Normal...
Page 91: Picture Size
Picture Size choose size and aspect ratio picture displayed on screen. Picture Size MENU m → Picture → Picture Size → ENTER E ― Different screen adjustment options are displayed depending on the current input source. • 16:9: Sets the picture to 16:9 wide mode.
Page 92 Position Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Wide Fit, Screen Fit or Custom. ― To use the Position function after selecting Zoom1, Zoom2, Wide Fit, Screen Fit or Custom, follow these steps. Press the d button to select Position.
Page 93 Resolution If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture quality by selecting the same resolution for the product as the PC using this menu. 1024x768 1280x768 1360x768...
Page 94: Auto Adjustment
Auto Adjustment Adjust frequency values/positions and fine tune the settings automatically. MENU m → Picture → Auto Adjustment → ENTER E Picture Auto Adjustment - Available in mode only. - The displayed image may differ depending on the model. PC Screen Adjustment Coarse Fine •...
Page 95: Picture Off
Picture Off Selecting Picture Off switches off the screen. The volume is not disabled. To switch the screen on, press any button other than the volume button. MENU m → Picture → Picture Off → ENTER E Picture Picture Off - The displayed image may differ depending on the model.
Page 96: On-Screen Display
OnScreen Display PIP Settings The picture from the external video source will be in the main screen and the picture from the product will be in the PIP sub- picture screen. MENUm → OnScreen Display → → ENTERE Main picture Sub picture OnScreen Display HDMI...
Page 97 PIP (Off / On): Activate or deactivate the PIP function. • • Source: You can select a source of the sub picture. Size ): Select a size for the subpicture. • Position Source • ): Select a position for the sub-picture. ―...
Page 98: Rotate Menu
Rotation Rotate menu Configure the menu screen. MENUm → OnScreen Display → Rotation → ENTERE • Landscape: Display the menu in landscape mode (default). • Portrait: Display the menu in portrait mode on the right side of the product screen. Rotation ―...
Page 99: Auto Protection Time
Screen Protection Auto Protection Time If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen. MENUm → OnScreen Display →...
Page 100 Timer Screen Burn Protection Screen Burn Protection. You can set the timer for Pixel Shift Screen Burn Protection feature stops automatically after a specified period of time. Timer Timer Immediate display Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Page 101: Message Display
Immediate display Screen Burn Protection Select the screen saver you want to display immediately. Pixel Shift Pixel Rolling bar Fading screen • Timer Side Grey Immediate display When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen. Light Dark •...
Page 102: Menu Transparency
Menu Transparency Adjust transparency of menu box. High Medium • MENU m → OnScreen Display → Menu Transparency → ENTER E OnScreen Display Menu Transparency Medium - The displayed image may differ depending on the model. Menu Language Set the menu language. ―...
Page 103: Reset Onscreen Display
Reset OnScreen Display This option returns the current settings under OnScreen Display to the default factory settings. MENU m → OnScreen Display → Reset OnScreen Display → ENTER E OnScreen Display Reset OnScreen Display - The displayed image may differ depending on the model.
Page 104: Sound Adjustment
Sound Adjustment Sound Configure the sound ( ) settings for the product. Sound Mode You can select a sound mode to suit your personal preferences. • Standard: Selects the normal sound mode. • Music: Emphasizes music over voices. MENU m → Sound →...
Page 105: Sound Effect
Sound Effect Configure your preferred sound effect for output sound. ― If Speaker Settings is set to External, Sound Effect is disabled. ― Available only when Sound Mode is set to Standard. MENUm → Sound → Sound Effect → ENTERE Virtual Surround Sound Effect This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head Related...
Page 106: Hdmi Sound
HDMI Sound Select whether to hear from AV(HDMI) or PC(DVI). AV(HDMI) PC(DVI) • MENU m → Sound → HDMI Sound → ENTER E Sound HDMI Sound AV(HDMI) - The displayed image may differ depending on the model. Sound on Video Call Select sound output to listen to during a video call.
Page 107: Speaker Settings
Speaker Settings TV Sound Output If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the products speakers and the speakers attached to your audio receiver. If this MENU m →...
Page 108: Reset Sound
Reset Sound The displayed image may differ depending on the model. Reset all sound settings to the factory defaults. MENU m → Sound → Reset Sound → ENTER E Sound Reset Sound - The displayed image may differ depending on the model.
Page 109: Network Status
Network Network Status You can check the current network and Internet status. MENUm → Network → Network Status → ENTERE Network Status Your wireless network and Internet connection are setup and ready to use. 00 : 12 : fb : df : 29 : 76 MAC Address ***.
Page 110: Network Settings
→ ENTERE Wired Wireless • Network Settings No network cable or Samsung Wireless LAN Adapter connected. Please plug in a network cable or a Samsung Wireless LAN Start Adapter. Cancel - The displayed image may differ depending on the model.
Page 111: Network Settings (Wired)
Network Settings (Wired) • Depending on how your network is configured, you may be able to attach your product to your LAN by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN cable.
Page 112 Set the network connection to use Internet services such as perform software upgrades. In the pop-up menu that appears, click Status. Automatic Network Settings (Wired) On the dialog that appears, click the Support tab. Connect to the network using a LAN cable. On the Support Tab, click the Details button.
Page 113: Network Setting (Wireless)
SSID and WPA key in either mode. Connecting to a Wireless Network ― If your router, modem, or device is not certified, it may not connect to the product via the “Samsung Wireless LAN adapter”. To connect your product to your network wireless, you need a wireless router or modem and a Samsung ―...
Page 114 Automatic Network Setup (Wireless) When done, use the right arrow button to move the cursor to Next, and then press E. The network connection screen appears and the verification process starts. Most wireless networks have an optional security system that requires devices that access the network Security Key.
Page 115 How to set up manually When done, select at the bottom of the page, and then press E. The network test screen appears and the verification process starts. Network Type Wireless from the Network Settings page. Your wireless network and Internet connection are When the connection has been verified, the Network function searches for available wireless networks.
Page 116: Multimedia Device Settings
Wi-Fi Direct MENUm → Network → Wi-Fi Direct → ENTERE To use this function, your mobile device Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router. Wi-Fi Direct.
Page 117: Server Network Settings
Server Network Settings Server Access Select a method to connect the server network. MENUm → → → ENTERE Network Server Network Settings Allow Deny • Connect to server FTP Mode Specify the FTP operating mode. Server Network Active Passive • Player To run connect to a network.
Page 118: Initial Settings (System)
System Setup Initial settings (System) After powering on the product for the first time, configure basic settings such as the language, channel and time. Press the button. MENU m → System → Setup → ENTER E ― Enter your 4 digit PIN number. The default PIN number is “0-0-0-0". Change PIN If you want to change the PIN number, use the function.
Page 119: Touch Control
Touch Control Configure touch control related features. Admin Menu Lock MENU m → System → Touch Control → ENTER E Admin Menu Lock Set the to display the administrator settings menu when you tap and hold the finger on the screen. System •...
Page 120: Clock Set
Time You can configure Clock Set Sleep Timer. You can also set the product to automatically turn on or off at a specified time using the Timer function. ― Press the INFO button if you want to view the current time. MENU m →...
Page 121: Source Autoswitch Settings
Source AutoSwitch Settings Turning on the display with Source AutoSwitch Settings On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. Source AutoSwitch Settings MENU m → System →...
Page 122: Power Control
Power Control Auto Power On This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed. MENU m → System → Power Control → ENTER E • PC module power Power Control The PC module can be turned on/off separately from the LFD.
Page 123: Standby Control
Standby Control Power Control You can set the screen standby mode to be applied when an input signal is received. Auto Power On Auto • Power-saving mode will activate if no input signals are detected even though a source device is connected to the display. PC module power The message No Signal...
Page 124: Eco Solution
Eco Solution Energy Saving Reduce the power consumption by adjusting the screen brightness. MENU m → System → Eco Solution → ENTER E Medium High • Eco Sensor Eco Solution To enhance your power savings, the picture settings will automatically adapt to the light in the room. Energy Saving •...
Page 125: No Signal Power Off
No Signal Power Off Eco Solution Save power by turning the device off when no signal is received from any source. Energy Saving 15 min 30 min 60 min • ― Disabled when an attached PC is in power saving mode. Eco Sensor ―...
Page 126: Device Manager
Device Manager Configure options for external input devices connected to the product. Keyboard Settings MENU m → System → Device Manager → ENTER E Configure keyboard connection settings or options for a connected keyboard. Device Manager Select Keyboard Keyboard Settings Select a keyboard you want to use from the available connected keyboards.
Page 127: Mouse Settings
Mouse Settings Device Manager Select Mouse Keyboard Settings Configure mouse connection settings or options for connected mouse devices. Mouse Settings ― Among connected mouse devices, only one mouse can be used. Mouse Options - The displayed image may differ depending on the model. ―...
Page 128: Change Pin
Play via Select the appropriate Play via mode depending on the environment where you are using the product. The home screen may be different depending on the setting. MagicInfo URL Launcher • MENU m → System → Play via → ENTER E System Play via MagicInfo...
Page 129 • - The displayed image may differ depending on the model. BD Wise Provides the optimal picture quality for Samsung DVD, Blu-ray and Home Theatre products which support Wise. When Wise is turned On, the picture mode is automatically changed to the optimal resolution.
Page 130: Anynet+ (Hdmi-Cec)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung BD Wise product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.
Page 131 Auto Turn Off Anynet+ (HDMI-CEC) Anynet+ Setting an Device to turn automatically when the product is turned off. Anynet+ (HDMI-CEC) • ― If Auto Turn Off is set to Yes, running external devices will turn off at the same time as the product powers off. Auto Turn Off ―...
Page 132: Troubleshooting For Anynet
Troubleshooting for Anynet+ Problem Possible Solution Anynet+ does not work. • Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only. • Check if the Anynet+ device power cord is properly connected. • Check the Anynet+ device’s Video/Audio/HDMI cable connections. •...
Page 133 Problem Possible Solution The connected device is not • Check whether or not the device supports Anynet+ functions. displayed. • Check whether or not the HDMI cable is properly connected. Anynet+ (HDMI-CEC) System • Check whether is set to in the menu.
Page 134: Hdmi Hot Plug
HDMI Hot Plug General This feature is used to activate the time delay to turn on a DVI/HDMI source device. Security • BD Wise DivX® Video On Demand Anynet+ (HDMI-CEC) Shows the registration code authorized for the product. HDMI Hot Plug If you connect to the DivXⓇ...
Page 135: Reset System
Reset System This option returns the current settings under system to the default factory settings. MENU m → System → Reset System → ENTER E System Reset System - The displayed image may differ depending on the model.
Page 136: Software Update
Version: This is the software version already installed in the product. Update the software to the latest version. Auto update This feature automatically updates the product when not in use. • Contact Samsung MENU m → Support → Contact Samsung → ENTER E View this information when your product does not work properly or when you want to upgrade the software.
Page 137 Go to Home Go to Home to play a variety of content from a memory device or a connected network. Player Accessible using the HOME button on the remote control. Search or play channels or content saved on devices. MENU m → →...
Page 138 Video Wall Customize the layout of multiple displays that are connected to form a video wall. In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo function. Natwork Status Check the current network and Internet connection.
Page 139: Reset All
Reset All This option returns all the current settings for a display to the default factory settings. MENU m → Support → Reset All → ENTER E Support Reset All - The displayed image may differ depending on the model.
Page 140: Playing Photos, Videos And Music (Media Play)
• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost. Samsung Electronics is not liable for any damage or loss of data. • Do not remove a USB device while it is loading.
Page 141 Compatible devices with media play • Some USB digital cameras, smartphones and audio devices may not be compatible with the product. • Media play is only compatible with USB MSC devices. • MSC device refers to a Mass Storage Class Bulk-Only Transport device. Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs.
Page 142: Using A Usb Device
Using a USB device Connecting a USB device Turn on your product. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. Player page automatically appears as soon as a USB device connects to the product. ―...
Page 143: Playing Media Content From A Pc/Mobile Device
Playing media content from a PC/mobile device Approving a PC/mobile device connection Play photos, videos or music saved on a PC or mobile device. To play media content from a PC or mobile device on the product, the connection with the PC or mobile device must be approved. ―...
Page 144: Features Provided In The Media Content List Page
Play content saved on a device connected to a home network. ― Playing media content using a non-Samsung DLNA server may result in a compatibility issue. ― Playback of some media content shared with a PC or mobile device may not be possible depending on the content encoding type or the content file format. Some functions may not be available.
Page 145: Menu Items In The Media Content List Page
Menu items in the media content list page Option Name Operations Photos Videos Music Slide Show Start a slideshow. ― This menu item is not available if Sort by is set to Folder. Encoding Select an encoding language if the title of media content appears corrupted. Rename Playlist Rename a playlist.
Page 146: Available Buttons And Features During Photo Playback
Available buttons and features during photo playback Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear. Pause Play • Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder. Previous Next •...
Page 147: Available Buttons And Features During Video Playback
Available buttons and features Option Name Operations during video playback Select Scene Thumbnails: Select a scene and play the video from the scene. ― Thumbnails is not available if 1) the thumbnail of the video is not extracted yet, 2) the video contains audio only or 3) the video play time is shorter than 60 seconds.
Page 148: Available Buttons And Features During Music Playback
Available buttons and features during music playback Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear. Pause Play • Pause or play music. Rewind Fast Forward • Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice. Previous Next •...
Page 149: Supported Subtitle And Media Play File Formats
Supported Subtitle and Media play file formats Subtitle External Internal • MPEG-4 timed text (.ttxt) • Xsub Container: AVI • SAMI (.smi) • SubStation Alpha • SubRip (.srt) Container: MKV • SubViewer (.sub) • Advanced SubStation Alpha • Micro DVD (.sub or .txt) Container: MKV •...
Page 150: Supported Music File Formats
Supported music file formats File Extension Type Codec Comments *.mp3 MPEG MPEG1 Audio Layer 3 *.m4a, *.mpa, *.aac, *.3ga MPEG4 *.flac FLAC FLAC The Seek (jump) function is not supported. Supports up to 2 channel Supported Video Formats • Video content will not play, or not play correctly, if there is an error in the content or the container. •...
Page 151: Resolution Frame Rate
File Container Video Codec Resolution Frame rate Bit rate Audio Codec Extension (fps) (Mbps) *.avi DivX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf ADMPCM MPEG4 SP / ASP *.wmv (IMA, MS) *.mp4 *.mov HE-AAC H.264 BP / MP / HP *.3gp...
Page 152: Troubleshooting Guide
Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Centre Before calling Samsung Customer Service Testing the Product Centre, test your product as follows. If the problem persists, contact Samsung Check if your product is operating normally by using the product test function.
Page 153: Check The Followings
Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product.
Page 154 Screen issue The screen is not clear. The screen is blurry. Adjust Coarse and Fine. Remove any accessories (video extension cable, etc) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product.
Page 155 Lines (red, green or blue) are displayed on the screen. These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a Samsung Service Centre to resolve the issue. The display looks unstable and then freezes.
Page 156 Sound issue The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software programme. Video is available but there is no sound. If an HDMI cable is connected, check the audio output settings on the PC.
Page 157 Sound issue There is an echo sound coming from the speakers. Different decoding speeds between the product speakers and external speakers can cause an echo. Speaker Settings to External. In this case, set Remote control issue The remote control does not work. Make sure that the batteries are correctly in place (+/-).
Page 158 Other issue The product smells like plastic. The plastic smell is normal and disappears over time. The monitor appears tilted. Remove and then attach the stand again to the product. Audio or video cuts out intermittently. Check the cable connection and connect it again if required. Using a very hard or thick cable may corrupt audio and video files.
Page 159 Q & A Question Answer How can I change the frequency? Set the frequency on your graphics card. • Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings. •...
Page 160 Question Answer How do I set powersaving mode? • Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display → Screen Saver Settings or BIOS SETUP on the PC. • Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver Settings or BIOS SETUP on the PC.
Page 161: Specifications
Specifications General Size Model Name DB32D DB40D Panel Size 80 cm 101 cm Display area 698.4 mm (H) x 392.85 mm (V) 885.6 mm (H) x 498.15 mm (V) Display area Dimensions (W x H x D) 721.4 x 420.3 x 49.9 mm 906.6 x 524.7 x 49.9 mm...
Page 162 Power Supply AC 100 to 240 VAC (+/- 10%), 60 / 50Hz ± 3Hz Refer to the label at the back of the product as the standard voltage can vary in different countries. Environmental Operating Temperature : 0 C ~ 40 C (32 F ~ 104 F) Humidity : 10 % ~ 80 %, non-condensing considerations Storage...
Page 163: Power Saving Mode
Power off Power off (SOG Signal : Not Support the (Power Switch) Rating Typical DPM Mode) Power Indicator Blinking Power Consumption DB32D 70 W 60 W 77 W 0.5 W 0.5 W DB40D 110 W 82 W 121 W DB48D...
Page 164: Preset Timing Modes
― Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical frequency to 60Hz using the CDT product before you exchange it with the LCD product. Model Name DB32D / DB40D / DB48D / DB55D Synchronization Horizontal Frequency...
Page 165 Resolution Horizontal Frequency Vertical Frequency Pixel Clock Sync Polarity (kHz) (Hz) (MHz) (H/V) VESA, 640 x 480 37.500 75.000 31.500 VESA, 800 x 600 35.156 56.250 36.000 VESA, 800 x 600 37.879 60.317 40.000 VESA, 800 x 600 48.077 72.188 50.000 VESA, 800 x 600 46.875...
Page 166: Responsibility For The Pay Service (Cost To Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service • Use of supplies or separatly sold product unspecified by Samsung. technician in the following cases. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. Not a product defect •...
Page 167: Correct Disposal Of This Product (Waste Electrical & Electronic Equipment)
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. (For India Only) This product is RoHS compliant. For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers - 18002668282, 180030008282.
Page 168: Optimum Picture Quality
Optimum Picture Quality and Afterimage Black Matrix Colour-Filter Common Electrode (ITO) Burn-in Prevention Optimum Picture Quality Source Drain • Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the panel. This does not affect product performance. - The number of sub-pixels by panel type: 6,220,800 •...
Page 169: Flight : Time
Preventing afterimage burn-in • Regular Text colour Change - Use bright colours of similar brightness. ― The best way to protect the product from afterimage burn-in is switching the power off or setting the Interval: Change text colour and background colour every 30 minutes PC or system to run a screen saver when not in use.
Page 170 In the case of using open source software, Open Source Licences are available on the product menu. Open Source Licence Notice is written only English. For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send email to oss.request@samsung.com.
Page 171 Terminology Non-interlace Mode and Interlace Vertical Frequency____ The product Component ports (green, blue and DVD (Digital Versatile Disc)____ DVD 480i / 480p / 720p / 1080i / red)____ The component ports, which 1080p____ Each of the scanning Mode____ Non-interlace mode displays a single image many times refers to a CD-sized mass storage disk rates above refers to the number of...

This manual is also suitable for:

Db40d Db48d Db55d

Samsung DB32D User Manual

Quick Links

Troubleshooting

Related Manuals for Samsung DB32D

Summary of Contents for Samsung DB32D

This manual is also suitable for:

Table of Contents