Intended Use; Assembly And Adjustments - DeWalt DCD700 Instruction Manual

ENGlIsh
the charger securely using drywall screws (purchased
separately) at least 1" (25,4 mm) long, with a screw head
diameter of 0,28–0,35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5,5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn
out the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
30
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
NoTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

This drill/driver is designed for light fastening and
drilling applications.
Do NoT use under wet conditions or in presence of
flammable liquids or gases.
These drills/drivers are professional power tools. Do NoT
let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Belt Hook (Fig. A)
DCD710

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or
suspend objects from the belt hook. ONLY hang
tool's belt hook from a work belt.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMpoRTaNT: When attaching or replacing the belt hook,
use only the screw 10 that is provided. Be sure to securely
tighten screw.
The belt hook can be be attached to either side of the
9
tool using only the screw
10
left- or right-handed users. If the hook is not desired at all, it
can be removed from the tool.
To move belt hook, remove the screw
belt hook in place then reassemble on the opposite side. Be
sure to securely tighten screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to select the
best speed for a particular application. The further you
provided, to accommodate
10 that holds the
1 . To turn