All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by PF0265 Service Singapore...
EN 2 SD-4.00SA_CH Technical Specifications 1. Technical Specifications Interfaces and Pin Assignments SD4 00_SA CH supports both configurations of single-disc and 5-disc changer SACD player. In table 1-1, interfaces or connectors stuffing options are given for applications of single-disc and 5-disc changer. Table 1-1 Interfaces or connectors stuffing options Disc Type 1100 1300 1301 1302 1500 1701 1702 1703 1704 1900 1012 1013...
Page 3
Technical Specifications SD-4.00SA_CH EN 3 24. GND 4. GND Ground 5. KOKDATA Karaoke PCM data (I2S format) 1.2.3 Optional Power Supply Connector at Location 1701: 6. GND Ground 7. KOKPCMCLK Karaoke PCM system clock 1. +3V3 Power supply +3V3 (I2S format) 2.
Page 4
128kHz / 176.4kHz / : Mute on : 3V3 ±0V3 192kHz. : Mute off: 0V ±0V3 Standard : Philips I2S output I2S data0 out : I2S front data output. Number of I2S outputs : Basic 6 channels: : Level - h / l...
Page 5
Technical Specifications SD-4.00SA_CH EN 5 is unable to output both RGB and YUV simultanious. Specification. : The output comply fully with [PQR-IMS] Class III. : DC level - sync bottom at 0.43V ±10% (100% white) and 0.9V ±10% (black). : Output impedance - 75Ohm.
EN 6 SD-4.00SA_CH Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes Safety Instructions Warnings 2.1.1 General Safety 2.2.1 General Safety regulations require that during a repair: • All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, "). Careless handling •...
Page 9
Mechanical Instructions SD-4.00SA_CH EN 9 4.1.1 Dismantling of DVD Mono Board Figure 4-3.The Tray is now disengaged and can be pulled outwards. See Figure 4-1 for dismantling of DVD module. When no disc is loaded, unlocking the Tray can also be done by moving the Slider A in the direction as shown in Figure 4-4 Unlock the OPU conn 1100, Sledge motor conn 1301 and pull the Tray outwards.
Page 10
EN 10 SD-4.00SA_CH Mechanical Instructions Service Hints 4.2.1 DVD Module This module can be repaired as follows: 1. The VAL6011/14 is a combination of loading mechanism and DVD-mechanism. Both the mechanism is not a repairable unit and in case of failure it has to be replaced with a new loader VAL6011/14.
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 11 5. Test Instructions Mono Board DVD-SD4.00SA_CH General 5.2.2 Reset Check: To ensure a proper start-up of the monoboard, the back-end • Impedance of measuring-equipment should be > 1MΩ. reset signal RESETn is required at the STi55xx input (testpoint •...
Page 12
EN 12 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-4 PC connection PM3380 B Connector pin Signal 1500-1 TXT_SER (STi55xx out) 1500-2 SERVICE-mode select 1500-3 RXD_SER (STi55xx in) 1500-4 RTS_SER (Not in use) 1500-5 1500-6 CTS_SER (Not in use) 1500-7 +5V_SER Now start the terminal program.
Page 13
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 13 5.3.2 Memory Check: 5.4.2 Audio Clock Switch Check The µP has a data bus that is connected to a Flash and also The internally generated Audio clock can be set to either 44.1 internal link to the MPEG SDRAM inteface.
Page 14
EN 14 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-13 NameTestpointWaveform PM3380B Name Testpoint Waveform PCMLRCLK F886 / F021 Refer to Figure 5-9 PCMSCLK F883 / F019 Refer to Figure 5-10 PCMDATA0 F884 Refer to Figure 5-11 DATA_LR/DSD_LEFT F025 Refer to Figure 5-11 DATA_LsRs/DSD_Ls F029 Refer to Figure 5-11...
Page 15
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 15 Alternatively, there is a check that can be done without A/V board. PM3394B First, let the decoder generate pink noise on the audio outputs. Table 5-14 Ref. # Command Name Remark AudioPinkNoiseOn Audio Pinknoise On Measure then these signals on level and frequency.
Page 16
EN 16 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH VIDEO PM3380B 5.5.1 Video Output Check Measure the DC voltages at all video-outputs at conn 1703 while the video signal is turned off: 1V ± 10% Generate a color-bar via next software commands: Ref.
Page 17
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 17 PM3380B PM3380B CH1 500mV~ BWLMTB20.0us L=1 ch1p CH1 500mV~ BWLMTB20.0us L=1 extp CL 16532163_061.eps 290102 CL 16532163_026.eps 230102 Figure 5-19 Y_VID Figure 5-21 B_VID (U) with video out at YUV 5.5.2 Slow Blanking Scart PM3380B An aditional part of the video-path is the scart function- switching test.
Page 18
EN 18 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-18 Video Hsync check Ref. # Command Name Remark Value Waveform VideoColDencOn ColourbarDENC ON 15.625 kHz 0.02% Vpeak-peak > 3V Refer to Fig 5-22 VideoColOutRGB RGB Colourbar ON 15.625 kHz 0.02% Vpeak-peak > 3V Refer to Fig 5-22 VideoColDencOff Colourbar DENC OFF...
Page 19
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 19 Table 5-24 Disc motor switching PM3380B Name Testpoint Frequency STDBY_MOTOR F308 high 4Vpp ± 0.5V Refer to MOTO1 I241 Figure 5-26 F301 Refer to Figure 5-27 F302 Refer to Figure 5-27 F303 Refer to Figure 5-27 F210 Refer to Figure 5-28...
Page 20
EN 20 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-26 Radial PM3380B Name Testpoint Value (Radial ON) Rad - F132 4.3V 0.5V Rad + F133 4.3V 0.5V F218 Refer to Figure 5-30 and 5-31 PM3380B CH1 2.00 V= MTB5.00ms ch1+ CL 16532163_032.eps 230102 Figure 5-28 T1-T2-T3...
Page 21
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 21 PM3380B PM3394B m1.1 CH1 2.00 V~ MTB 500ms ch1+ CH1 2.00 V~ MTB 250ns ch1+ CL 06532147_010.eps CL 16532163_054 161100 290102 Figure 5-33 SL+ / SL- ( SLEDGE OUTWARDS ) Figure 5-32 SL 5.6.5 Tray: Check DC vtg on the following testpoint when Sledge at Inward...
Page 22
EN 22 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-33 Tray opens Table 5-35 Focus motor switching Name Testpoint Value (Tray opening) Name Testpoint Value (Focus OFF) TRAY - F340 2.0V 1.0V FOC - F134 5V 0.5V TRAY + F338 6.0V 1.0V FOC + F130...
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 23 Measure DVDALAS outputs PM3380B Table 5-38 DVDALAS outputs Name Testpoint Value F104 1V 10% F107 1V 10% F108 1V 10% F110 1V 10% F113 1V 10% F112 1V 10% At output HFN, the following waveform can be measured : CH1 2.00 V~ MTB 500ns Refer to Figure 5-40...
Page 24
EN 24 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Overview of Interfaces player. This special cable will also connect the test pin, which is available on the connector, to ground (i.e. activate test pin). The table below shows an overview of the user interfaces of the Activation Diagnostic Software.
Page 25
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 25 Termination The menu interface is terminated by switching off the DVD DD: > 16 (Execute CompSdramWrR nuclei) player. 1600 OK @ DD: > 5.9.2 Command Line Interface CL 16532163_042.eps 230102 The command line interface is part of level 1 diagnostic mode. Via a command line interface the execution of Diagnostic Nuclei can be controlled.
Page 26
EN 26 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Front Panel... MAIN > AUDIO > SINE WAVE MENU Basic Engine... Audio Sine On [21a] Processor Peripherals... Audio Burst On [21b] Error Log... Furore... MAIN > AUDIO > DIGITAL PORTS MENU Miscellaneous... LFE_SEL High [56a] LFE_SEL Low...
Page 27
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 27 NVRAM Modify [36] Jump To Outside Grooves [42c] NVRAM Read/Wr Test [15] Screen Layout With Menus MAIN > MISCELLANEOUS > STATISTICS INFO MENU When menus are used, no specific screen layout can be given: Total Nr Of Times Tray Open [47a] menu information will not be in a special format, except for the...
Page 28
EN 28 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH 5.11 Diagnostic Nuclei Each nucleus contains an atomic and independent diagnostic test, testing a functional part of the DVD player hardware on component level. Each Nucleus returns a result message to its caller.
Page 29
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 29 Table 5-40 Basic diagnostic nuclei Ref. # Reference Name Remark DAC_AudioPreMuteOn Enable Audio Pre-mute Ref. # Reference Name Remark BasicSpAcc Serial port Access test/ DAC_AudioPreMuteOff Disable Audio Pre-mute initialization BasicInterconDram Data and address bus DAC_CenterOn Enable Center on pin Interconnection (only for...
Page 30
EN 30 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH Table 5-44 Video Ref. # Reference Name Remark MiscApplVer Read version of Ref. # Reference Name Remark application software VidPortOutAA Output the value 0XAA at MiscTrayOpenNr Read the number of the Digital Video Interfac times the tray opened e Port MiscPowerOnTime...
Page 31
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 31 Table 5-48 Basic engine 5.12.1 Audio Nuclei Ref. # Reference Name Remark Error BeVer Version number code Error text BeFocusOn Focus On 1880 Test successful 1800 Test successful BeFocusOff Focus Off 1900 Test successful BeDiscmotorOn Discmotor On...
Page 32
EN 32 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH 5.12.2 Basic Engine Nuclei Error code Error text 4242 “Unexpected response from Basic Engine” Error code Error text 4243 “Communication time-out error” 3900 Test successful 4244 “Basic Engine returned error number 0xXX” 3901 “Parity error from Basic Engine to Serial”...
Page 33
Test Instructions Mono Board DVD-SD4.00SA_CH SD-4.00SA_CH EN 33 Error Error code Error text code Error text 5820 Test successful 5840 Test successful 2600 “The ROM version of the slave processor = 0xXX, and the internal ID = 0xYY” 5860 Test successful 2601 “I2c bus busy”...
Page 34
EN 34 SD-4.00SA_CH Test Instructions Mono Board DVD-SD4.00SA_CH 5.12.5 Log Nuclei Error code Error text 5301 “I2c bus busy” Error code Error text 5302 “I2c bus not working“ 3100 "Show error log" 5320 Test successful 3101 "Error log is invalid" 5321 “I2c bus busy”...
STi55XX (SDRAM) The SD4.0SA_CH modules consist of the Mercury 3 Loader (back-end VAL6013/01 (from Philips Optical Storage), and a Mono Board. processor) (FLASH) The module is capable of analogue video (with option for digital YUV video) and digital audio and SACD decoding.
Page 52
EN 52 SD-4.00SA_CH Circuit Descriptions, List of Abbreviations and IC Data • One for CD with a wavelength of 780 nm. • One for DVD with a wavelength of 650 nm. The spindle-motor interface provides both motor control signals The TZA1033 (item 7105) controls the data from these lasers, from the demodulator and, in addition, contains a tachometer and the supply to them.
Page 53
Circuit Descriptions, List of Abbreviations and IC Data SD-4.00SA_CH EN 53 • The video encoder supports Closed Caption and allows Furore processing part is not used during all other play modes. MacroVision 7.0/6.1. In these modes, the PCM audio signals are fed through the •...
Page 54
EN 54 SD-4.00SA_CH Circuit Descriptions, List of Abbreviations and IC Data – Stereo DSD only output. DSD_stereo: 2-channel DSD An external analogue-to-digital converter (ADC), acting as output with stereo down mix in the case of 5- and 6- slave, is required to convert the microphone signals to I2S channel, and normal stereo in case of 2-channel DSD signals.
Page 55
The Furore 2 and Sti5580/Sti5588 (Video) use this clock. It is For sets with Mask-ROM software, replace it with a used to derive the PCM audio clocks 256*FS by the programmed Flash (available via your Philips Service MK2703STR. This IC is also used to buffer the incoming 27 organisation).
Page 56
Serial Clock I2C SCLK Audio serial bit clock Serial Data I2C SDRAM Synchronous DRAM S/PDIF Sony Philips Digital InterFace SRAM Static RAM STBY Standby SVCD Super Video CD Software Total Harmonic Distortion Transistor Transistor Logic (5V logic)
Circuit Descriptions, List of Abbreviations and IC Data SD-4.00SA_CH EN 57 IC Data In this paragraph, the internal blockdiagrams and pinning are given of ICs that are drawn as 'black box' in the electrical diagrams (with exception of 'memory' and 'logic' ICs). 9.4.1 Diagram M1 DVDALAS2plus Advanced Analogue DVD...
Page 58
EN 58 SD-4.00SA_CH Circuit Descriptions, List of Abbreviations and IC Data DVDALAS2plus Advanced Analogue DVD TZA1033 Signal Processor and Laser Supply PINNING handbook, full pagewidth CD-A CD-B CD-C CD-D CD-REF VDDA4 CD-E VSSA4 CD-F VDDA1 VSSA1 O-CENTRAL DVD-MI LPF-DPD2 LPF-DPD1 DVD-A DVD-B FTC-REF...
Circuit Descriptions, List of Abbreviations and IC Data SD-4.00SA_CH EN 61 9.4.3 Diagram M6 2 UART & Internal peripherals 2 SmartCards Central CACHE SUBSYSTEM command port (C2+) Front-end & link interface Clock DMAs ICache generator SRAM Refill control DCache Diagnostic JTAG controller debugging...
Page 62
EN 62 SD-4.00SA_CH Circuit Descriptions, List of Abbreviations and IC Data PIO2[5] CPU_DATA[13] PIO2[6] CPU_DATA[12] PIO2[7] CPU_DATA[11] VDD3_3 CPU_DATA[10] CPU_DATA[9] PIO3[0] CPU_DATA[8] PIO3[1] PIO3[2] VDD2_5 PIO3[3] CPU_DATA[7] PIO3[4] CPU_DATA[6] PIO3[5] CPU_DATA[5] PIO3[6] CPU_DATA[4] PIO3[7] CPU_DATA[3] VDD2_5 CPU_DATA[2] CPU_DATA[1] B_DATA CPU_DATA[0] B_BCLK CPU_CAS1 B_FLAG...