Advertisement
Quick Links
Troubleshooting
The power indicator blinks red.
-The ID of this product is not yet registered
in the Center Module and a wireless
connection cannot be made. Register ID in
the Center Module of the target.
The power indicator lights red.
-The battery is almost exhausted. Replace
the battery with a charged one.
Cannot turn on the headset.
-The battery is exhausted. Replace the
battery with a charged one.
-The battery is not inserted correctly.
Position the battery properly.
Cannot communicate with another
headset or the customer at the order
post.
-The Center Module may be turned off. Turn
on the power switch of the Center
Module. If no remedy exists, consult your
dealer for repairs.
-The headset ID is not registered in the
Center Module of the target. Register ID in
the Center Module of the target.
-The [S] +[P] or [S] + [T] buttons may have
been pressed at the same time, causing the
extended functions to start. Turn the power
off and then back on.
Cannot hear or talk to the speak post, but
communications with other headsets are
OK.
-The vehicle detector may be malfunctioning
because the detector is not plugged into the
Center Module, no power is supplied, or the
detecting function is out of order. Check that
the vehicle detector is plugged in and has
power. If no remedy exists, consult your
dealer for repairs.
Cannot "talk" or "page" in certain areas.
-Radio waves cannot reach the area Remove
any metal obstacles blocking radio waves.
Charging
Use the supplied charging attachment to
charge the battery with the battery charger.
The charging time is approximately 3 hours
(when charged from empty to full). For
details on the indicator during charging,
refer to the operating instructions for the
battery charger.
When the charging attachment (accessory) is
attached to the battery charger as shown in
the figure below, insert the battery while
matching the terminals
.
Included Accessories
PGGX1006ZAC1 - Color tips – Black
PGGX1006ZBC1 - Color Tip – Red
PGGX1006ZCC1 - Color Tip – Blue
PGGX1006ZDC1 - Color Tip – Green
PGGX1006ZEC1 - Color Tip – Yellow
2FA1CH455P - Charging attachment
Optional Accessories
WX-SB100 - Battery
(Li-ion 3.7 V DC, 700 mAh)
WX-Z3040A - Battery Charger
Consumables
PGHG1521ZAC1 - Head Pad
(Adjustment Slide Pad)
PGHG1520ZAC1 - Ear Pad
PGUR1108ZAC1 - Headband
PANASONIC
ATTUNE II
HD3 HEADSET
CHEAT SHEET
05/28/2021 r2.0
Advertisement
Related Manuals for Panasonic ATTUNE II HD3
Summary of Contents for Panasonic ATTUNE II HD3
- Page 1 PGGX1006ZAC1 - Color tips – Black the Center Module of the target. PGGX1006ZBC1 - Color Tip – Red PANASONIC -The [S] +[P] or [S] + [T] buttons may have PGGX1006ZCC1 - Color Tip – Blue been pressed at the same time, causing the PGGX1006ZDC1 - Color Tip –...
- Page 2 Headset registration Talk Button Functions: 1) Set the Center Module to “ID Registration” mode. Modes: Refer to the operating instructions of the Center Modul Push to Talk: 2) Rotate the microphone boom to turn off the power Adjustable Headband Click and hold to talk. the headset. Release button to listen. Talk Lock: 3) Rotate the microphone boom while holding down th [T] and [P] buttons to turn Click button once to talk. Head Pad on the power of the headset. Click button again to listen. ● The headset enters the ID Registration setting mode. You will hear “Registration Mode” and the power indica Page Button Functions: ...