Page 1
BT10.3GL/BT10.3BGL 100 cm Glass chimney hood waeady...
Page 2
User Manual for your Baumatic BT10.3GL/BT10.3BGL Cooker Hood 100 cm Glass chimney hood NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference;...
Contents Page Environmental note MPORTANT SAFETY INFORMATION pecifications of your cooker hood sing your Baumatic cooker hood leaning your Baumatic cooker hood The grease filter aintenance Removing and cleaning the grease filter Changing a light bulb Fitting the carbon filters...
NVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person.
IMPORTANT: DO NOT THAN 700mm ABOVE YOUR COOKER. o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. y is of the utmost importance to Baumatic. 700 mm 700 mm 800 mm SET YOUR COOKER HOOD LESS...
Page 6
you handle your appliance, es cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. If other types of flue or appliances are fitted, an adequate supply of air in the room.
Page 7
removing air f rom your room. Ensure that proper ventilation measures are being observed. Note that the cooker hood rem kitchen, not steam. Warning - Always en hood has been disconnected from the power supply before carrying out any wor on the hood, including cleaning and replacing light bulbs.
Congratulations on purchasing a Baumatic Cooker ood! DIMENS IONS: Width (canopy Depth (canopy): Height (with chimney) DIMENSIONS OF CHIMNEY SECTION: 308 mm x 275 mm Your stainless stee l Cooker Hood is fitted with: o High extraction tangential motor...
Page 9
Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. Find the control panel, which is located at the front right canopy. o There are several buttons on the control panel, which perform separate functions.
Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOU AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid deter gent and a new damp cloth.
Maintenance m ving and cleaning the grease filters o Soak the grease filt ers in hot about an hour. o Rinse it off thoroughly with hot water. o Repeat the process if required. o Refit the grease filt ers once they have dried. o IMPORTANT: Let the grea refitting them in the cooker hood.
IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUS HAVE D ISCONNECTED THE COOKER HOOD FROM YOUR MAINS S o Prior to touching the light bul down. o Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy o Use a screwdriver to remove the glass cover that sits over the...
If h t e appliance is going to be used in recirculation mode then it is ecessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE T COOKER HOOD FROM YOUR MAINS SUPPLY.
nstallation IMPORTANT: Bef all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filters The manufacturer de lines all responsibility in the event of the installer iling to observe all the accident prevention regulations in force, hich are necessary for normal use and the regular operation of the...
correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the o The brown wire must be connected to th Before beginning i all tion o Check that the product purchased is of a suitable size for the chosen installation area.
walls and ceilings. However a qualified technician must verify the suitability of the materials, in accordance with the type of wall and ceiling. The wall and ceiling must be strong enough to tak the weight of the hood. Do not tile, grout or silicone this appliance to the wall. This appliance is designed to b Ins a t lling your cooker hood...
Page 17
2 Position the hood against the wall that you are intending to stall it on and mark the position of the support holes that are be drilled (as shown in the figure below). a) The support screw holes are indicated by figure A in this drawing nd the anchoring screw holes are indicated by figure B.
Page 18
4) Insert rawl plugs into all of 5) Fasten the support screws halfway in, leaving them 10 mm out of the wall. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Tighten the anchoring screws fully into the wall.
8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting ho discharge outlet that is suitab have a cross section of at least 150 cm².
Page 20
10) Lift chimney section D upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the side measurements of both sides of chimney section D on the wall with a pencil and then remove chimney section D. ) Take the fixing bracket (E) and place it between the two pencil ma s rk that you made in step 9.
Page 21
2) Using an 8 mm drill bit, drill out two holes on the pencil markings at you made in step 11. Insert rawl plugs into the holes and then se a screwdriver to secure the fixing bracket to the wall. o Refit chimney section C to the hood and fix it onto the hood using the two screws that a o Secure the top of chimney section C to the fixing bracket, usi...
The only alternative is to recirculate the air. o I need a charcoal filter? All cooker hoods have grease filters but if you are using your c hood in recirculation mode, then a charcoal filters must be fitted in addition to the grease filters. ode?
Troubleshooting IMPORTANT: If your cooker hood ap properly, before contacting the Baumatic Service Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is My cooker hood is not working effectively.
Page 24
Or any installation other an the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance when it is delivered.