Transporting The Unit; Installing The Unit - Fujitsu WOYK150LJL Installation Manual

When an obstruction is present also in the upward area (Unit : mm)
(1) Obstacles at rear and above
Max. 500
1000
or more
100
or more
3.3.2. Multiple outdoor unit installation
• Provide at least 100 mm of space between the outdoor units if multiple units are
installed.
• When routing the piping from the side of an outdoor unit, provide space for the piping.
• No more than 3 units must be installed side by side.
When 3 units or more are arranged in a line, provide the space as shown in the
following example when an obstruction is present also in the upward area.
When the upward area is open (Unit : mm)
(1) Obstacles at rear only
300 or more
(3) Obstacles at front and rear
When an obstruction is present also in the upward area (Unit : mm)
• Obstacles at rear and above only
Max. 300
1500 or more
3.3.3. Outdoor unit installation in multi row
* The following settings are not recommended in case of cooling by a low outside tem-
perature. (Unit: mm)
(1) Single parallel unit arrangement
100 or
more
2000 or
more
600 or more
1000 or more
(2) Obstacles at rear, sides, and above
1500
or more
300
80
or more
or more 100
or more
(2) Obstacles at front only
1500 or more
500 or more
1500 or more
1500 or more
500 or more
(2) Multiple parallel unit arrangement
500 or
more
3000 or
more
600 or more
1500 or more

3.4. Transporting the unit

Do not touch the fi ns. Otherwise, personal injury could result.
When carrying the unit, hold the handles on the right and left sides and be careful.
If the outdoor unit is carried from the bottom, hands or fi ngers may be pinched.
Hoisting method
• When hoisting the outdoor unit, hook the rope on the outside of the foot as shown in
the fi gure.
• Use suffi ciently strong rope to bear the unit's weight.
• Place protective board or fi ller cloth at the place where the cabinet may come into
contact with the rope to prevent damages. Without using them, the cabinet may be
damaged or deformed.
• The center of gravity of the outdoor unit is shifted to the right. Be careful not to tilt to
the heavy side causing it to fall.
• To prevent accidents caused by the unit swinging or falling down, do not apply any
impact to the unit when it is hanging.
• When hoisting, do not hook the rope to the thermistor holder on the back of the
outdoor unit.
Product mass
(Kg)
138
Protective
boards
Foot
Lifting by forklift
• When using the forklift to lift the unit, pass
the forklift arms through the opening space
of the wooden delivery pallet.
• Be careful not to damage.
Carrying by hand
• Carry slowly in the manner
Fig. A
as shown on "Fig. B" hold-
ing the handles "Fig. A"
in right and left sides. (Be
careful not to touch with
hands or objects.)
• Be sure to hold the
handles on the sides of
the unit. Otherwise, the
Handle
suction grilles on the
sides of the unit may be
deformed.

3.5. Installing the unit

• Install 4 anchor bolts at the locations indicated with arrows in the figure.
• To reduce vibration, do not install the unit directly on the ground. Install it on a secure
base (such as concrete blocks).
• The foundation shall support the legs of the unit and have a width of 80 mm or more.
• Depending on the installation conditions, the outdoor unit may spread its vibration during
operation, which may cause noise and vibration. Therefore, attach damping materials
(such as damping pads) to the outdoor unit during installation.
• Install the foundation, making sure that there is enough space for installing the connec-
tion pipes.
• Secure the unit to a solid block using foundation bolts. (Use 4 sets of commercially avail-
able M10 to M12 bolts, nuts, and washers.)
• The bolts should protrude 20 mm. (Refer to the figure.)
• If overturning prevention is required, purchase the necessary commercially available
items.
195 688
80
Air
WARNING
CAUTION
700 to
1000 mm
Light
Heavy
side
side
Wooden delivery
pallet
Fig. B
Handle
Handle
195 Unit: mm
80
Bolt
Nut
Base
En-4