Advertisement
2.
INTRODUCTION AND OPERATION
2.1.
INTRODUCTION
Composite bodied spotlight with carry handle. Integral stand keeps lens
and battery case off the floor and permits light to be directed where it is
needed. Ø180mm Lens with halogen bulb produces ten million candle
power of intense white light, suitable for a variety of industrial, domestic
and leisure applications. Powered by 12V 7Ah sealed lead acid battery.
Supplied with carry strap, in-car charging cable and 230 - 12Volt battery
charger pack.
2.2.
OPERATION
WARNING! Ensure you read and understand safety instructions
before use.
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a
consumable item and its ability to accept charge will reduce over time.
We will warranty it against mechanical and electrical defect for a
period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly
conditioned, its capacity will diminish. Under these circumstances we
will not replace the battery pack even if it is less than one year old.
Reminder: This spotlight is designed for intermittent use only.
Continuous use may damage the unit.
1. Charge the battery before use. IMPORTANT: Turn off spotlight
while charging. Failure to do so will damage the charger plug/
vehicle plug.
2. Turn spotlight 'On' and 'Off' by the the rocker switch (fig. 2C) one
bar is the high intensity spotlight and two bars is the low intensity
flood light
3. The spotlight has a fixed carrying handle and an adjustable standing
support (fig. 1A.).
2.3.
BATTERY CHARGING
WARNING! Ensure you read, understand and apply safety
instructions relating to the battery and charger before use.
2.3.1. Mains charger plug
1. Plug the charger adaptor (fig. 3) into the jack inlet on spotlight body
(fig. 2E) and stand the spotlight in a safe location ready to charge.
2. Ensure the spotlight is turned 'Off' and then plug charger into the
mains supply. The indicator LED will light (fig. 2F).
3. The battery will take approximately 24 hours to charge on the
initial charge and 18 hours for subsequent charges. Switch off the
mains supply and unplug the charger. Remove the charger adaptor
(fig.3) from the spotlight and seal the jack inlet. The spotlight may
now be used.
4. Store the charger in a safe, dry location.
Note: a) A fully charged battery will last for approximately 40 minutes
on full beam (spotlight) and 60 minutes on low intensity beam
(flood
light).
b) There is no need to fully discharge the battery before recharging.
2.3.2. Vehicle plug
1. Ensure spotlight is turned 'Off' and then plug the 12 volt vehicle
plug adaptor (fig. 4.) into the jack inlet on the spotlight body
(fig. 2E). Stand the spotlight in a safe location ready to charge.
2. Insert plug into vehicle cigarette lighter socket. The indicator LED
will light. Allow approximately 3 hours for charging with the engine
running.
3. Unplug the adaptor from the vehicle socket and from the spotlight
before turning the spotlight on.
4. Store the adaptor in a safe, dry location.
Note: Charging the spotlight from a 12 volt vehicle socket will drain the
vehicle battery if the engine is not running.
2.4.
12V DC socket
1. Ensure that the 12V DC appliance spotlight and the 12V DC socket
are switched off.
2. Connect your appliance's 12V DC adaptor into the 12V DC socket
(fig. 5A).
3. Turn on the 12V DC supply with the rocker switch to position (I)
(fig. 2D).
4. Turn on the 12V DC appliance.
5. When fully charged turn off the 12V DC appliance then turn off the
power to the 12V DC socket by pressing the rocker switch to the
(O) position.
fig. 2
fig. 3
fig. 5
Original Language Version
fig. 1
fig. 4
AK438.V2
Issue: 3 - 20/12/11
Advertisement
