Related Manuals for Philips PREMIUM 10501
Summary of Contents for Philips PREMIUM 10501
- Page 1 Premium 10501 11-07-2000 P10501a07.doc.DOC Maintenance instruction Premium 10501 PHILIPS LASER OPTICS MAINTENANCE INSTRUCTION PREMIUM 10501 Philips Components...
- Page 2 No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. © 2000 Philips Electronics N.V. All rights reserved Philips components Page 2...
- Page 3 Optical Storage PECS Shanghai Keywords: High-end Audio Jukebox CD10 VAU1254 Premium 10501 Note: The publisher reserve the right to change the data mentioned in this document without prior notice. © 2000 Philips Electronics N.V. All rights reserved Philips components Page 3...
- Page 4 Premium 10501 11-07-2000 P10501A07.DOC draft Maintenance instruction Premium 10501 Revision history Version Date Remarks Version 0.1 11-07-00 draft version © 2000 Philips Electronics N.V. All rights reserved Philips components Page 4...
-
Page 5: Table Of Contents
1.1 Handling of the unit ............................6 1.2 Laser current measurement instruction...................... 7 1.3 Lens cleaning instruction ..........................8 1.4 Cleaning and lubrication of the mechanical parts ..................9 © 2000 Philips Electronics N.V. All rights reserved Philips components Page 5... -
Page 6: Introduction
Never touch the lens with your fingers, and avoid that grease from the mechanical parts is spoiled on the lens. Do not move the sledge by pushing it by hand, but moving the sledge by spinning the sledge motor worm gear with your fingers. © 2000 Philips Electronics N.V. All rights reserved Philips components Page 6... -
Page 7: Laser Current Measurement Instruction
The location of resistor R3208 can be found in the component placement sheets and is located close to the micro controller between the micro controller and the power connector. © 2000 Philips Electronics N.V. All rights reserved Philips components... -
Page 8: Lens Cleaning Instruction
The direction of movement of the cotton tip should be 90 degree to the radial tracking movement of the actuator as indicated in the figure below. Move cotton tip in this direction © 2000 Philips Electronics N.V. All rights reserved Philips components Page 8... -
Page 9: Cleaning And Lubrication Of The Mechanical Parts
1.4.1 Removal top cover. Figure 1 Removal of black plastic cover (4 screws) Using a Torx screwdriver No 6. The OPU spindle is now accessible from the topside © 2000 Philips Electronics N.V. All rights reserved Philips components Page 9... - Page 10 Provide a short circuit clip or a paperclip to the leads of the OPU flex foil in order to protect the laser and electrical circuitry against E.S.D. © 2000 Philips Electronics N.V. All rights reserved Philips components Page 10...
- Page 11 Grease Add on the OPU spindle one dot of grease between the two bearings holes. It is not necessary to remove the metal cover of the CD unit. © 2000 Philips Electronics N.V. All rights reserved Philips components Page 11...
- Page 12 • Lubrication of Actuator Spring clip Grease (Actuator spring clip) Figure 6 Press down the actuator sledge spring and add one drop of grease on the spring © 2000 Philips Electronics N.V. All rights reserved Philips components Page 12...
- Page 13 • Lubrication third bearing (Top side) Grease Bearing bearing spring Figure 8 Add 2 dots of grease on the guidance pane at each side of the 3 bearing spring © 2000 Philips Electronics N.V. All rights reserved Philips components Page 13...