Download Print this page
Sealey HT102R.V2 Quick Manual

Sealey HT102R.V2 Quick Manual

3w cree xpe led rechargeable head torch with auto sensor

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1.
GENERAL
DO NOT shine directly into your, another person's or an animal's eyes.
8
DO NOT allow children to use the torch.
8
DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
8
1.2.
BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or service the batteries.
8
DO NOT crush, puncture, short contacts or dispose of in fire or water.
8
DO NOT expose to temperatures above 60°C (140°F).
8
2. INTRODUCTION
Hands-free head torch with adjustable 3W CREE XPE LED spotlight to direct light as required. One switch features an auto sensor to activate
light with the wave of a hand and standard on/off switch. Produces up to 125 lumens. Other switch has four options - full, 50% energy saving
mode, flash and red light. Powered by a rechargeable 3.7V 1.2Ah Li-ion battery. Supplied with micro USB charging lead.
3. SPECIFICATION
Model No: ........................................................... HT102R.V2
LED Qty: ...................................................................3W LED
Lumen Output (100% / 50%): .............................125lm / 73lm
Operating time (100% / 50%) ....................................3hr / 4hr
Battery: .....................................................3.7V 1.2Ah Li-Poly
Charging Time: ..................................................................4hr
4. OPERATION
4.1.
CHARGING (fig.2)
4.1.1.
Connect the USB lead to the port on the bottom of the head torch (fig.2).
4.1.2.
The red LED sections on the front face of the unit (fig.1, fig.3) will light in sequence whilst
the unit is charging.
4.1.3.
When the unit is fully charged 5 red LEDs on the unit's front face will light permanently.
4.2.
BATTERY INDICATOR (fig.3)
4.2.1.
Depress Light mode switch and hold for 3 seconds. Right hand red LEDs turn on.
5 LEDs lit indicates 100%, 1 LED lit indicates 20%.
4.3.
LIGHTING MODES (fig.1)
4.3.1.
5 different operational modes are available. By depressing the Light mode switch (fig.1)
within 3 seconds of each depression it is possible to cycle through them.
1st click - Maximum white light
2nd click - Dim white light (50% power saving)
3rd click - White light strobing
4th click - Red lights on
5th click - Red lights strobing
© Jack Sealey Limited
3W CREE XPE LED RECHARGEABLE HEAD
TORCH WITH AUTO SENSOR
HT102R.V2
MODEL NO:
Original Language Version
fig.1
fig.2
fig.3
HT102R.V2 | Issue 2 03/07/19

Advertisement

loading

Summary of Contents for Sealey HT102R.V2

  • Page 1 HT102R.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Store torch in a dry childproof area. BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.