Quick Info (Limited Tools Menu) - Husqvarna Automower 405X Workshop Manual

4.4.4.2 Tools - Test - User interface
Tools - Test - User interface menu shows:
The
Keypad :
•
1. Push the OK button to start the keypad test.
2. Push a button. The display shows the button that
is pushed.
3. Push the Back button to exit the test.
Display :
•
1. Push the OK button to start the display test. The
display flashes.
2. Push the Back button to exit the test.
Sound :
•
1. Push the OK button to start the sound test. The
buzzer emits a short sound signal at the same
time as a note is shown in the display.
2. Push the Back button to exit the test.
4.4.4.3 Tools - Test - Charging station
This function is used to check if there is a signal for A, F,
N and the guide wires.
1. Place the product in the charging station.
Note: The product and the charging station must be
paired.
2. Push the OK button to start the test.
4.4.4.4 Tools - Test - GPS navigation
Tools - Test - GPS navigation menu shows:
The
Enabled (Yes/No) : GPS navigation can be activated
•
Installation - Lawn coverage - GPS supported
via
navigation .
Installed (Yes/No) : If NO is shown, make sure that
•
the GPS module or the Automower
module is correctly installed and that the products
firmware has been updated.
Signal quality : Signal quality shows the strength of
•
the GPS signal reception. To get a satisfactory
function, signal quality should be
Map (BUILDING/COMPLETE) : BUILDING is
•
displayed the first time the product is used or after
the GPS map has been reset. Once the map is
COMPLETED will be displayed, which
completed,
takes 2 to 5 days.
4.4.5 Tools - Special settings
Tools - Special settings contains settings that
Note: The
are only available for service personnel.
Tools - Special settings menu shows:
The
Demo : The setting is used for installations in shops
•
or exhibitions. The product alternates between short
periods of operation, docking and charging.
Installation lock : If the installation settings lock is
•
activated, it is not possible to change any settings in
the Installation menu.
1582 - 001 - 23.12.2020
4.4.6 Tools - Calibrate
The
•
•

4.5 Quick info (Limited Tools menu)

The
When the start page or the main menu is displayed:
1. Push and hold down the 0 key for 2 seconds to
4.5.1 Quick info - Info
The
in
- Info on page 10 .
4.5.2 Quick info - History
The
and
The
•
•
®
Connect
The
menus as in
to
4.5.3 Quick info - Advanced
Good .
The
•
•
Note: The installation settings lock must be
deactivated to change any of the installation settings
in the main menu.
Tools - Calibrate menu shows:
Tilt sensor calibration : If the product does not
operates as expected in slopes it might help to
calibrate the tilt sensor. Place the product on a
horizontal surface and start the calibration.
Cutting height calibration : The cutting height
calibration can be enabled and the calibration set to
start the next time the product starts.
Quick info menu is a limited Tools menu .
Quick info menu.
access the
Quick info - Info menu has the same sub-menus as
Tools , except for the sub-menu Motors . Refer to Tools
Quick info - History menu has 2 sections: Messages
Search times .
History - Messages menu shows:
Fault messages : The 50 last fault messages
Info messages : The 50 last information messages.
History - Search times menu show the same sub-
Tools - History, total - Search times . Refer
Tools - History, total - Search times on page 12 .
Quick info - Advanced menu shows:
Automatic passage handling : The guide corridor
width is adjusted automatically. If
handling is disabled, the corridor width settings must
be made manually. To disable the
handling : Unselect Auto passage handling and push
the OK button.
Installation shape :
Open : Applicable in a large open work area with
•
a small number of obstacles and no passages,
or when the mowing result is uneven in steep
slopes.
Normal : Applicable in a work area with a
•
moderate number of obstacles and/or passages.
Applicable for most work areas.
Complex : Applicable in work areas with many
•
obstacles and/or passages.
Auto passage
Auto passage
Special menus - 13