Takeway G1 User Manual

T R I P O D
1
Our sincere gratitude
Takeway® G1 Tripod is well-designed to support T1 Clampod
1) for shots taken in the standing position, and it maintains Takeway
products' great quality, portability, and lightweight. Takeway® G1
Tripod makes T1 Clampod easier to use for shooting in the standing
position with various electronic products such as the 6-3 digital
single-lens reflex cameras (DSLR). By adding accessories, it can be
used as a simple support stand to hold tablets or be used
independently for digital cameras and any other device with 1/4 inch
screw adapter. The tripod itself only weighs 77g; however, it has a
maximum load capacity of 3 kg and can be carried in small handbags.
Wherever you go, enjoy the convenience and possibilities brought by
the Takeway® G1 Tripod.
2
Please test the relevant components
and read responsibility statement
before using this product
Before using this product on your consumer electronic products,
please check Takeway ® G1 tripod and its accessories for damage or
deformity. If there is any, please contact the salesperson to exchange
your product to prevent damage of your consumer electronic
products or personal injury caused by the flawed product. The
company takes no responsibility and assumes no liability for the loss
or inconvenience caused by user's own negligence.
3
Product components
Fixing Protective User Guide
Bracket Pad
(Note 2)
Tripod Body
4
Operation notes
4-1: The body of the clamp is made of stainless, but do not place the
product in a humid environment for a long time to avoid product being
damaged.
4-2: Do not place the product near heat or open flame which will
damage the plastic components.
4-3: If the product has not been used for a long time, please check the
components and functions work normally, so that it does not fall when
it is used on the electronic products.
4-4: When shooting in standing position, please make sure that the
tripod stands firmly on a flat surface.
4-5: After the product is assembled, please place it on a flat surface to
check for its stability. When using this product for standing shooting,
USER GUIDE
Before using the product for the first time, please read through the user guide.
Please use this product correctly after fully understanding the content of the user guide.
do not remove your hands from your electronic product when
installing it on the clampod. Make sure that the clampod stands firmly
on the surface before shooting, so that your electronic product will not
(Note
be damaged caused by the fall of the clampod.
4-6: When using the Takeway® G1 Tripod, please make sure your 3C
device is stable and can maintain its balance.
5
Parts name
1 1/4" Screw
Tripod Body
2
Front Feet
3
6
Assembly and Operation
6-1: Assembling, disassembling, and storing with the
Takeway® T1
6-1-1: Remove the Original
6-1-1
T1 Stand
T1 comes with a Takeway®
factory stand, as shown in
A
figure. Remove the factory stand
by sliding it upwards and store it
in the storage pouch.
6-1-2: Assembling the T1
6-1-2
Line the groove of the G1 with
the A bottom crossbar of the T1
stand. Press and secure it.
Attach the fixing bracket with
5
the mark facing forward ( as
B
fig shows). Attach the G1 to the
clampod and secure it by
tightening the screw. Shake it
lightly to make sure that it is
firmly fixed to prevent devices
from falling during use.
6-1-3: Storing G1
After assembling the G1
3 4
support can be stored at the
bottom when not in use to avoid
obstacles when clamping. Please
note that when storing, start with
the front feet.
3
6-1-4: Complete assembling the
After Feet
4
6-2: Mounting and using the T-B01 Ballhead
The T-B01 Ballhead (Note 2)
instructions is a standard accessory for the T1. We
5 Fixing Bracket
recommended purchasing additional
separately) for added convenience when using.
6-2-1: Mounting and using the
T-B01 Ballhead
Line the screw with the A screw
hole at the base of the T-B01
Ballhead. Use a flathead
screwdriver to secure the
platform. Shake gently to make
sure it is secured to prevent items
from falling and getting damaged
during use.
6-2-2: Complete the mounting of the
T-B01 Ballhead
A
6-3: Mounting and using digital cameras
When using the G1 Tripod independently, the shooting angle may
be more limited. We recommend purchasing a T-B01 Ballhead
5
(sold separately) for added convenience.
6-3-1: Mounting a digital camera
Line the screw with the A screw
hole at the base of digital camera.
Use a flathead screwdriver to
A
tighten the screw. Shake gently to
make sure the base is screwed in
tightly to prevent the product from
loosening during use.
B
6-3-2: Complete the mounting of a
4
digital camera
7
6-1-3
Specifications of the product
the
4
3
Model number:
T1 +
Materials:
Screw of the quick
release plate:
Load capacity:
*Example illustration only.
This product does not contain T1 CLAMPOD.
referred to in the assembly
T-B01 Ballhead (sold
8
Safety warning
6-2-1
8-1: Please follow the operation notes. The company takes no
responsibility for any man-made damage.
8-2: G1 is only recommended for static using.
A
8-3: Do not apply any volatile solvents (kerosene, paint thinner) on the
product surface.
8-4: If the product is damaged or deformed from falling or impact,
please stop using the product anymore, so that your electronic
product will be damaged from any malfunction.
8-5: An adult must accompany when children under the age of 12 are
using the product.
9
Note
Note 1: The maximum load capacity of the
6-3-1
kg (including the Ballhead).
A
Note 2: The T-B01
Takeway® products. Please contact near by
more information.
Note 3: The complimentary protective pad is designed to protect the
camera surface. Place on camera surface as needed.
G1
Size: Extended: 9.5x4x2.4 cm
Folded:15x11.5x3.7cm (LxWxH)
Weight: 77g
High-class stainless steel
1/4"
3kg
Takeway® G1 Tripod is 3
Ballhead is an accessory designed for
Takeway® stores for