HP NetServer E 800 Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. NetServer e 800
  6. Installation manual

HP NetServer E 800 Installation Manual

Hide thumbs Also See for NetServer E 800:
Table of Contents

Advertisement

Quick Links

Download this manual
HP NetServer E 800
Installation Guide
HP Part Number D9394-90000
Printed June 2000

Advertisement

Table of Contents
loading

Related Manuals for HP NetServer E 800

Summary of Contents for HP NetServer E 800

  • Page 1 HP NetServer E 800 Installation Guide HP Part Number D9394-90000 Printed June 2000...
  • Page 2 Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

  • Page 3: Table Of Contents

    Contents Setting Up the HP NetServer E 800..............1 Introduction ....................1 Step 1: Attaching all the Cables..............2 Step 2: Opening the HP NetServer............3 Step 3: Installing Memory ................5 Step 4: Installing Mass Storage Devices............ 6 Step 5: Installing Adapter Boards............. 10 Step 6: Installing a Second Processor .............

  • Page 5: Setting Up The Hp Netserver E 800

    Setting Up the HP NetServer E 800 Introduction This installation guide is a quick reference for HP NetServer E 800 installation. Skip any steps that do not apply to your installation. Refer to the figures below for connection and operating information. For more information, refer to the HP NetServer E 800 User Guide.

  • Page 6: Step 1: Attaching All The Cables

    Step 1: Attaching all the Cables If you are not installing any accessories, attach all available cables to the respective connectors, then go to "Step 7: Configuring the HP NetServer." NOTE The two USB connectors are reserved for printers, scanners, and external modems.

  • Page 7: Step 2: Opening The Hp Netserver

    Setting Up the HP NetServer E 800 Step 2: Opening the HP NetServer Tools Required: • ¼ inch flat-blade screwdriver • Torx T-15 driver WARNING Before removing the cover, always disconnect the power cord and remove the telephone cable. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry.
  • Page 8 Setting Up the HP NetServer E 800 Front of Chassis Cover Cover Bottom of Chassis Latch Opening Air Duct Latch...

  • Page 9: Step 3: Installing Memory

    • DIMMs may be installed in any slot, in any combination (sizes mixed), in any order, but HP recommends starting at slot 0 and filling the slots in order with the largest size first: 0, 1, 2, and 3. •...

  • Page 10: Step 4: Installing Mass Storage Devices

    The NetServer is internally limited to 7 mass storage shelves. The flexible disk drive and CD-ROM drive, which are standard on all models of the HP NetServer E 800, occupy shelves 1 and 2 respectively. • If a backup tape drive is used, it will occupy shelf 3.
  • Page 11 Setting Up the HP NetServer E 800 3. Connect the cables (data & power). 4. Replace the drive cage. Slots for Tabs Tabs(2) Captive Screws (3) First insert screws through round holes in back (one on each side). CAUTION All mounting screws used to thread into the hard disk drive must be #6-32 and not exceed ¼-inch in length.
  • Page 12 Setting Up the HP NetServer E 800 5. If necessary, install the internal accessory SCSI cable into SCSI channel B and connect to the SCSI drives or optional backup tape drive. Use HP NetServer E 800 External/Internal SCSI Cable Kit, part number P1773A. Terminator...
  • Page 13 Setting Up the HP NetServer E 800 6. If necessary, install the external/internal SCSI cable into SCSI channel B and connect to the knock-out in the rear of the chassis. Use HP NetServer E 800 External/Internal SCSI Cable Kit, part number P1774A. WARNING Ensure you do not touch the sharp metal edges from the knock-out once you have removed it.

  • Page 14: Step 5: Installing Adapter Boards

    Setting Up the HP NetServer E 800 Step 5: Installing Adapter Boards • The NetServer E 800 has two PCI (Primary and Secondary) busses and both are pear-to-pear, which provides approximately equal performance, except when using the two 64-bit slots versus the 32-bit slots.
  • Page 15 Setting Up the HP NetServer E 800 System Board (Top View) 32-bit PCI Slot 1 Wake- PCI Slot 2 32-bit Full- 64-bit PCI Slot 5 Length 64-bit PCI Slot 6 32-bit PCI Slot 7...
  • Page 16 Setting Up the HP NetServer E 800 Slot Cover Chassis Cross- Section View...
  • Page 17 Setting Up the HP NetServer E 800...

  • Page 18: Step 6: Installing A Second Processor

    Both processors must have the same clock speed and cache size. • Use only processor upgrade kits with the same HP product number. This ensures the product numbers are compatible and the processor type, clock speed, and cache size are the same.
  • Page 19 Setting Up the HP NetServer E 800 1. Open the ZIF (Zero Insertion Force) lever on the processor socket. The ZIF lever must open completely to a full 90° before removing the terminator from the socket. 2. Remove the terminator from the processor socket.
  • Page 20 Setting Up the HP NetServer E 800 3. Insert the processor into socket, matching pin-1 to marker. Pin-1 Marker 4. Close the ZIF lever with a click. The ZIF lever should click when closed.
  • Page 21 Setting Up the HP NetServer E 800 5. Place the Heatsink-Fan on top of processor and follow the steps A-C in the figure below. Hook Latch (hidden) B. Rotate back and A. Rotate and hook the Thumb Latch. hook. Thumb Latch C.
  • Page 22 Setting Up the HP NetServer E 800 6. Connect the fan connector to the respective connector on the system board. Processor 1 (CPU 1) CPU 1 Fan System Power Connector Processor 2 (CPU 2) CPU 2 Fan CAUTION Failure to connect the fan connector will cause the processor to overheat and the NetServer will shut down without any messages being displayed.

  • Page 23: Step 7: Configuring The Hp Netserver

    Perform a manual install if you are installing a NOS other than Novell NetWare or Microsoft Windows 2000 (NT) Server, you have replaced HP components (for example, replacing an HP Network Interface Card (NIC) with a NIC not on HP’s Tested Products List (TPL) or adding a...
  • Page 24 4. Refer to the HP NetServer Online Documentation CD-ROM: ◊ Use this CD-ROM for updated information about your HP NetServer and as reference for any additional information not provided in this Installation Guide.

Table of Contents