Radial Engineering HotShot DM1 Owner's Manual

FEATURE AND FUNCTIONS
INPUT jack connects from a dynamic mic.
1
2 OUTPUT-1 connects to main console or 1st channel. This
output is normally active.
OUTPUT-2 connects to sub-mixer or main console
3
2nd channel. This output is active only when the toggle
footswitch is held down.
4 TOGGLE footswitch is momentary and routes the mic
signal to output-2 when depressed.
LIFT switch disconnects the ground on pin-1 of output-2.
5
14 gauge steel enclosure is compact and made for heavy-
6
duty stage use.
7 Rugged glass-filled nylon XLR connectors are 100%
isolated to help reduce ground loops.
3 2 1
7
6
4
5
Radial Engineering HotShot DM1 User Guide
IMPORTANT NOTICE!
The DM1 is designed for dynamic microphones and is not intended
for use with condenser microphones. Before you start it is impor-
tant that you understand that since there are literally thousands of
different sound system variables, we have no way of checking how
the HotShot DM1 is used in the field.
You are responsible to ensure the safe and proper use of the DM1.
Using the DM1 confirms you have taken full responsibility. If you
are not 100% sure of your actions, please consult a qualified tech-
nician for advice.
RADIAL LIMITED THREE YEAR TRANSFERABLE WARRANTY
Radial Engineering - a division of JP Cabletek Electronics Ltd. warrants this product to be
free from defects in material and workmanship to the original owner and will remedy any
such defects free of charge according to the terms of this warranty. Radial Engineering
will repair or replace at its option any defective component(s) of this product, excluding the
finish, the footswitch (footswitch is warranted for 90 days) and wear and tear from normal
use, for a period of three (3) years from the original date of purchase. In the event that a
particular product is no longer available, Radial Engineering reserves the right to replace
the product with a similar product of equal or greater value. To make a request or claim
under this limited warranty, the product must be returned prepaid in the original shipping
container (or equivalent) to Radial Engineering or to an authorized repair centre and you
must assume the risk of loss or damage. A copy of the original invoice showing date of
purchase and the dealer name must accompany any request for work to be performed
under this limited warranty. This limited warranty shall not apply if the product has been
damaged due to abuse, misuse, misapplication, accident or as a result of service or
modification by any other than an authorized repair centre.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE
HEREOF AND DESCRIBED ABOVE. NO WARRANTIES, WHETHER EXPRESSED
OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND
BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE
YEARS.
RADIAL ENGINEERING SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPE-
CIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE
USE OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON
WHERE YOU LIVE.
Radial Engineering HotShot DM1 User Guide
True to the Music
HotShot DM1
Owner's Manual
Order # R800 1500
CAUTION: PLEASE READ THE IMPORTANT NOTICE ON
THE BACK COVER BEFORE USING THE HOTSHOT DM1
Radial Engineering
1638 Kebet Way, Port Coquitlam BC V3C 5W9
Tel: 604-942-1001 Fax: 604-942-1010
email: info@radialeng.com
Radial Engineering is a division of C•TEC (JP CableTek Electronics Ltd.)
Radial HotShot DM1 users guide Sept.. 2005, V1.0 - Part #: R870 1100 00
Subject to change without notice