Page 6
Safety Read the information contained in this section ‘Safety precautions’, before attempting to install or operate the equipment. Ensure that all electrical connections are properly made in accordance with instructions in the documentation, and periodically check that the connections have not worn or become damaged.
Page 7
Earth integrity WARNING This equipment must be connected to an earthed AC mains utility outlet. Static Electricity Precautions This equipment contains components that may be damaged by static discharge if handled carelessly. When you install any internal options, take care not to damage either the equipment or the options through careless handling.
Page 8
Power cord selection The power cord for this unit has been packed separately and has been selected according to the country of destination. It must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original cord set.
Page 9
Parallel Tandem For units set at 115 V: For units set at 230 V: use a parallel blade, grounding type use a tandem blade, grounding type attachment plug rated 15 A, 125 V. attachment plug rated 15 A, 250 V. For units set at 230 V (outside of the United States and Canada): use a cord set consisting of a minimum AWG according to the table above and a grounding type attachment plug rated 15 A, 250 V.
Page 10
As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: The wire which is colored Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or colored Green or Green and Yellow.
Page 11
Electromagnetic compatibility (EMC) Europe Directive 89/336/EEC This is a Class A equipment and suitable for installation in both a commercial and domestic environment. The product is designed to provide reasonable protection against harmful interference if installed correctly as instructed in this manual. USA - Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
Page 12
Where plug-in printed circuit board assemblies, disk drives, tape drives or other assemblies are fitted in this equipment by the user, or peripheral devices connected externally to this equipment, such assemblies or devices not supplied by Fujitsu LTD. via your system supplier MUST: Conform to the safety requirements of IEC 950 or the applicable equivalent national requirements.
Chapter 1 Overview 1.1 Introduction Redundant power supply unit is the option power supply unit which will be installed in SYSTEMs. PRIMERGY F200/F250 CAUTION : Don’t use expect for these Server model series. Models : PGTF2AXXX,PGTF2BXXX Note: ’X’ : any alphanumerical character or blank It loads Redundant power supply unit into SYSTEM and it makes a power supply redundant composition.
Chapter 2 Parts explanation Fault lamp (Orange) This lamp lights when AC power is supplied. Power lamp (Green) This lamp lights when the redundant power supply unit is in normal operation.
Chapter 3 Mounting of extension redundant power supply unit When constructing the power supply of the SYSTEM in a redundant power supply configuration, additionally install an optional redundant power supply unit into the SYSTEM. Please refer to the PRIMERGY F200/F250 operating manual for instructions on how to install.
Chapter 4 Replacing redundant power supply unit If the SYSTEM is redundant power supply configuration, a faulty redundant power supply unit can be replaced without disconnection of the SYTEM from the AC power supply. Please refer to the PRIMERGY F200/F250 operating manual for instructions on how to replace. CAUTION When exchanging a redundant power supply unit, always ask our maintenance engineer in case of replacing.
Page 19
PRIMERGY 電源ユニッ ト (PG-PU106) 取扱説明書 Redundant Power Supply unit (PGUPU106) USER'S GUIDE B7FY-0301-01-00 発 行 日 2002年7月 発行責任 富士通株式会社 Issued on July, 2002 Issued by FUJITSU LIMITED Printed in Japan ●本書の内容は、改善のため事前連絡なしに変更することがあります。 ●本書に記載されたデータの使用に起因する第三者の特許権およびその他の 権利の侵害については、当社はその責を負いません。 ●無断転載を禁じます。 0207-1 ア...