Advertisement
Quick Links
StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows XP SP2)
1. Preface
To establish the wireless connection between StarBoard FX/FX-DUO and the PC, the
following devices are necessary:
Wireless USB Device Server:
USB2.0 WiFi Adapter:
StarBoard Software 8.0/B or higher is necessary prior to setup of the wireless connection.
Make sure to select "FX/FX-DUO" in the Board Type screen during the installation of
StarBoard Software.
Installation of GW-US54GXS driver
- Log on as Administrator to install.
- Do not plug the USB2.0 WiFi Adapter into the computer until 4(3).
- Disable the firewall on Windows XP and commercial security software during installation.
2. GW-US54GXS Setup
(1) Run the installer of FW-US54GXS. If the menu is not displayed automatically,
double-click on "GW-US54GXS_Windows_v6.17.0000_CE.exe" in the CD-ROM root.
(2) Select "Next".
All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
Silex technology SX-2000WG+
Planex GW-US54GXS
1
Advertisement
Related Manuals for Hitachi StarBoard FX
Summary of Contents for Hitachi StarBoard FX
- Page 1 StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows XP SP2) 1. Preface To establish the wireless connection between StarBoard FX/FX-DUO and the PC, the following devices are necessary: Wireless USB Device Server: Silex technology SX-2000WG+ USB2.0 WiFi Adapter: Planex GW-US54GXS StarBoard Software 8.0/B or higher is necessary prior to setup of the wireless connection.
- Page 2 (3) Select “Next”. (4) Select “Continue Anyway. (5) Select “Finish”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 3 (2) Reset SX-2000WG+ as shown below (a) Hold pressing the reset button (b) Plug the power cable (c) Hold pressing the button until the LED turns red, then release the button. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 4 (4) Insert the CD-ROM bundled with SX-2000WG+ into the PC and select “Device Server Setup”. If the menu is not displayed automatically, double-click on “Autorun” in the CD-ROM root. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 5 (5) Select “Wired”. (6) Select “Yes”. (7) Select “Next”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 6 If still not listed, please disconnect and connect the network cable, and restart the device Server (Disconnect and connect the power cable). Please wait 2 minutes to configurate wireless connection. If still not listed, please go back to Step (a)-(c) in Section 3(2) All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 7 If the same parameters are used for other network, use a different subnet address such as 192.168.1.1. If you are not sure, please ask the network administrator. (11) Select “SSID:GROUP” “Channel:11” and select “Detailed Config”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 8 If you install multiple device servers in a close range, please assign unique SSID for each device server. For example, use the room name and so on. (13) Select “Execute”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 9 (14) Select “Finish” and install SX Virtual Link. (15) Click on “English” and select “Next”. Skip to (16) if the window is not appear. (16) Select “Next”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 10 (17) Select “Yes”. (18) Select “Next”. (19) Select “Next”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 11 (20) Select “Start” (21) Select “Yes”. (22) Select “Finish”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 12 (23) Select “Quit” (24) Select “Yes” All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 13 (2) Please check if the top LED is blinking green. Please refer to Trouble Shooting 7(2) (3) Plug GW-US54GXS into the PC. (4) Click on “No, not this time” and select “Next”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 14 (5) Select “Next”. (6) Select “Continue Anyway”. (7) Select “Finish”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 15 Please wait 2 minutes to configurate wireless connection. If still not listed, please go back to Step (a)-(c) in Section 3(2) (10) Check button name was changed to “More Setting”, then click on ”X” All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 16 (11) Click on “Start” Right-click on ”My Network Places” and select “Properties”. (12) Right-click on the entry for GW-US54GXS and select “Properties”. (13) Click on “Internet Protocol (TCP/IP)” and select “Properties”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 17 IP Address to be used If you did not use the default parameters for SX-2000WG+, please use the relevant parameters. If you are not sure, please ask the network administrator. (15) Select “Close”. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 18 Broadcast Address to be used If you did not use the default parameters for SX-2000WG+, please use the relevant broadcast address. If you are not sure, please ask the network administrator. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 19 SX-2000WG+ and GW-US54GXS. (6) Run “Start”→”All Programs”→” StarBoard Software”→” StarBoard Software”.You can see if FX/FX-DUO is connected by the task tray icon. not connected connected not connected connected FX-DUO All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 20 (3) Click on the USB device entry listed in the window and select “Connect”. FX-DUO (4) You can see if FX/FX-DUO is connected by the task tray icon. not connected connected not connected connected FX-DUO All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 21 If the LED is not still blinking green, please go back to Section 3 and set up again. If still not, the unit might be faulty and contact the support for SX-2000WG+. Please refer to “Device Server Setup CD” for support center information. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 22 “0% loss” is displayed Network Connection Established ping 192.168.0.1 “100% loss” is displayed Network Connection Not Established. After trying all the trouble shooting, please contact the support for SX-2000WG+. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 23 (a) Unplug USB cable from SX-2000WG+, then the USB device entry listed in the window will be disappeared after 30 seconds. FX-DUO (b) Plug USB cable from SX-2000WG+ again, and the USB device will be listed in the window. Then click “Connect” FX-DUO All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 24 In order to re-setup GW-US54GXS, please uninstall the driver and install it again in accordance with following instruction. (a) Confirm GW-US54GXS is plugged on PC. (b) Run “Start”→”All Programs”→”bRoad Lanner Wave”→” Uninstall GW-US54GXS Utility”. (c) Select “OK”, then uninstall start. All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.
- Page 25 (d) Installation wizard window will be appeared, then select”Finish” (e) Unplug GW-US54GXS from PC (f) Follow section 2 “GW-US54GXS Setup” to setup -end of file- All Rights Reserved. Copyright © 2008, Hitachi Software Engineering Co., Ltd.