Page 2
AG-Stomp This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated.
SPECIFICATIONS Digital Section • Full Digital Signal Processing • Mic Simulator: 8 Types • Feedback Reduction: 5-band • Digital Effects • Limiter • Digital Chorus, Digital Delay • Hall Reverb, Room Reverb, Plate Reverb • External Controller Function (EXP Pedal/MIDI): 8 Controllers/ Parameters •...
PANEL LAYOUT Top Panel Display & Main Section Display & Main Section Effect Section Foot Switch Section UP Button DOWN Button MANUAL Button UTILITY Button STORE Button Display AG-Stomp Pre-Amplifier Section...
Page 6
AG-Stomp Pre-AmpSection MIC TYPE Select Switch (MIC TYPE) BLEND Control (BLEND/STEREO) VOLUME Tone Controls OUTPUT Level Control SHIFT Button Effect Section LIMITER Button LEVEL Feedback Reduction Buttons Frequency Control (FREQ) DEPTH Control CHORUS/DELAY Effect Buttons SPEED/TIME Control DEPTH/FEEDBACK Control LEVEL Reverb Effect Buttons REVERB Volume...
Page 7
Footswitch Section Footswitches 1, 2, 3 Bank Switch (AUTO F.R./BANK/TUNER) Rear Panel Power Switch (STAND-BY ON/OFF) Power Adaptor Jack (AC IN 12V 1A) Guitar Power Supply Switch MIDI OUT Jack MIDI IN Jack Digital Output Jack (DIGITAL OUT) EXP. PEDAL Jack Headphone Jack (PHONES) Output Jacks (OUTPUT R, L/MONO) INPUT Jack...
WIRING CN301 CN304 CN303 CN310 (V611450) CNB-V698560 CN302 CN309 (V611470) (V611460) Note) When installing the DM circuit board, use care not to have the wire assembly caught by the bottom case. (V611480) AG-Stomp CN305 (V610850) CN307 CN306 CN308 CN101 W102 W101...
AG-Stomp DISASSEMBLY PROCEDURE Bottom Case (Manhour requirement: 5 min.) Remove the six (6) screws marked [30]. The bottom case can then be removed. (Fig. 1) Bottom [30]:Bind Head Tapping Screw-B 3.0x8 MFZN2BL (EP600190) DM Circuit Board (Manhour requirement: 15 min.) 2-1.
Page 13
Topcover [T70]:Washer 9.0 MFZN2Y (ET800150) [T110]:Bind Head Tapping Screw-B 3.0x8 MFZN2BL (EP600190) PN Circuit Boards (1/2, 2/2) (Manhour requirement: 20 min.) 3-1. Remove the bottom case. (See Procedure 1.) 3-2. Remove the DM1/2 and DM2/2 circuit boards. (See Procedure 2.) 3-3-1.
Page 14
AG-Stomp Heat Sink (Manhour requirement: 25 min.) 4-1. Remove the bottom case. (See Procedure 1.) 4-2. Remove the DM circuit board. (See Procedure 2.) 4-3. Remove the two (2) screws marked [A-a] from the soldered face of the DM circuit board and the three (3) screws marked [A-b] from IC112, IC113 and IC114.
LSI PIN DESCRIPTION HD6413002FP16 (XQ375A00) CPU NAME FUNCTION Port A Address bus Power supply Port B PB6//DREQ0 PB7//DREQ1 /RESO Reset Ground P90/TXD0 Transmit data (MIDI OUT) P91/TXD1 KSN-ACK P92/RXD0 Receive data (MIDI IN) P93/RXD1 KSN-RX P94/SCK0 Port 9 P95/SCK1 Port 9 P40/D0 P41/D1 P42/D2...
Page 16
AG-Stomp YSS910-S (XV988A00) DSP6 (Digital Signal Processor) NAME Power supply (3.3 V) Ground System master clock input (60 MHz or 30 MHz) System master clock output (High or 30 MHz) Power supply (5 V) /SYNCI Sync. signal input /SYNCO Sync. signal output Power supply (5 V) System clock input (30 MHz) System clock output (30 MHz)
Page 17
YM3437C-F (XM530A00) DIT2 (Digital Format Interface Transmitter) NAME FUNCTION Ground MCLK Master clock input DIN/BCLK/WCLK format select DM1,DM0=0,0 DSP,LDSP (64 bit,LSB first) DM1,DM0=0,1stereo,DSP (64 bit,MSB first) DM1,DM0=1,0 DSP2 (128 bit,MSB first) DM1,DM0=1,1 BB (64 bit,MSB first) System reset WCIN Word clock input Digital audio serial data input Power supply (+5 V) AK4520A-VF-E2 (XT802A00) DAC &...
AG-Stomp IC BLOCK DIAGRAM MB3790PF(XR967A00) DM: IC4 ASSP N.C. CONTROL N.C. BAT1 BAT2 SENSE ALARM1 ALARM1 RESET RESET 74AHC32DT XZ103A00 DM: IC5, IC6 74HC244DT(XZ109A00) DM: IC14, IC15, IC16 Bus Buffer VDD(Vcc) (GND)Vss CONTROL 590k Reference Voltage 1.24V Power Supply Circuit SENSE 240k V th:3V...
Page 19
74HC374DT(XZ102A00) PN: IC301~IC307 D-FF OUT PUT CONTROL D CK CLOCK NJM5532M (XC011A00) DM: IC102, IC103 NJM4556AMT1 (XQ138A00) DM: IC105, IC106 OP AMP A OUT A IN B OUT B IN A+IN B+IN 74HC4052DT(XZ101A00) PN: IC308, IC309 Multiplexer Y-COM Y-COM X-COM X-COM AG-Stomp NJM072M(XC458A00)
AG-Stomp CIRCUIT BOARDS DM 2/2 Circuit Board INPUT MONO/TRS for POWER SUPPLY Component side DM 1/2 Circuit Board CN101: to PN1/2-CN301 DIGITALOUT COAXIAL to PN1/2-C...
Page 21
AG-Stomp DIGITALOUT COAXIAL POWER SUPPLY ON/OFF to PN1/2-CN302 to PN1/2-CN303 to PN1/2-CN304 Component side CNA-V717790...
AG-Stomp TEST PROGRAM A. CONNECTION OF TERMINALS • INPUT Monaural input • OUT L/MONO Balance output (RL 47K ) • OUT R Balance output (RL 47K ) • HEAD PHONES Stereo output (RL 33 ) • EXP. PEDAL FC7 or Connect VR of B50K. JK pin 1: MIN of VR JK pin 2: MAX of VR JK pin 3: CENTER of VR...
Page 29
SW Check (1) Using the UP and DOWN switches, select “1”. (This step can be skipped if “1” is already selected.) (2) Press the STORE switch. (3) Starting with the UP switch, press each switch whose LED lights up one after another. After “MIC”, “BANK”, “3”, “2”...
Page 30
AG-Stomp (11) Push in the EXP. PEDAL. !4 • All LED segments light up and go out, and then the checking proceeds to MIDI check. • If VR, SW or EXP PEDAL is not set at its center position, checking will result in an error and E. 0 will appear at the left end of LED.
AG-Stomp ERROR MESSAGES If an error occurs during operation, one of the following error message numbers will appear in the display. Stop operation of the AG-Stomp and follow one of the solutions described below. : MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received and the buffer is full SOLUTION: Try reducing the amount of data being sent, or break the data into smaller blocks.
ACOUSTIC GUITAR PRE-AMPLIFIER PARTS LIST CONTENTS OVERALL ASSEMBLY ELECTRICAL PARTS Notes : DESTINATION ABBREVIATIONS A : Australian model B : British model C : Canadian model D : German model E : European model F : French model H : North European model I : Indonesian model J : Japanese model WARNING...
Page 45
AG-Stomp OVERALL CIRCUIT DIAGRAM 3/3 (DM) SRAM SRAM FLASH ROM from B (P2.K6) to A (P2.K6) DSP6 AG-Stomp ASSP DRAM DRAM REGULATOR AG-Stomp PHOTO COUPLER BUFFER to PN1/2-CN304 (P1.E5) BUFFER to PN1/2-CN303 (P1.E5) BUFFER to PN1/2-CN302 (P1.G8) INVERTER BUFFER AG-Stomp...