Specifications - Makita HM1317C Instruction Manual

ENGLISH (Original instructions)
1-1. Switch lever
2-1. Adjusting dial
3-1. Power-ON indicator lamp (green)
3-2. Service indicator lamp (red)
4-1. Set bolt
4-2. Nut
4-3. Side handle

SPECIFICATIONS

Blows per minute
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for chiselling work in concrete, brick,
stone and asphalt as well as for driving and compacting
with appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For Model HM1307C
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Work mode : chiseling function with side handle
Vibration emission (a
Uncertainty (K) : 2.0 m/s
Explanation of general view
5-1. Bit
5-2. Tool retainer
5-3. Tool holder
6-1. Bit with collar
6-2. Bit without collar
8-1. Rear cover
8-2. Hex wrench
Model
Overall length
Net weight
Safety class
) : 81 dB(A)
pA
) : 101 dB(A)
WA
value (tri-axial vector
2
) : 12.5 m/s
h,CHeq
2
HM1317C
715 mm
17.0 kg
ENE045-1
For Model HM1307CB
For European countries only
Noise
The typical A-weighted noise level determined according
ENF002-1
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Vibration
The vibration
determined according to EN60745:
Work mode : chiseling function with side handle
Vibration emission (a
ENG102-2
Uncertainty (K) : 1.5 m/s
For Model HM1317C
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
ENG216-2
Sound pressure level (L
Sound power level (L
sum)
Uncertainty (K) : 3 dB(A)
Vibration
The vibration
determined according to EN60745:
Work mode : chiseling function with side handle
Vibration emission (a
Uncertainty (K) : 1.5 m/s
3
9-1. Crank cap
10-1. Hammer grease
11-1. Rear cover
11-2. Hex wrench
12-1. Crank cap cover
13-1. Hammer grease
HM1307C HM1317CB
730 - 1,450
15.3 kg 19.0 kg
/II
) : 81 dB(A)
pA
) : 101 dB(A)
WA
Wear ear protection
total value (tri-axial
) : 12.0 m/s
h,CHeq
2
) : 81 dB(A)
pA
) : 101 dB(A)
WA
Wear ear protection
total value (tri-axial
) : 8.5 m/s
h,CHeq
2
HM1307CB
824 mm
17.3 kg
ENG102-2
ENG216-2
vector sum)
2
ENG102-2
ENG216-2
vector sum)
2