Midi Out - Yamaha MOTIF ES6 Data List

(3-3) REGISTERED PARAMETER NUMBER
STATUS 1011nnnn(BnH)
LSB 01100100(64H)
RPN LSB 0ppppppp
MSB 01100101(65H)
RPN MSB 0qqqqqqq
DATA ENTRY MSB 00000110(06H)
DATA VALUE 0mmmmmmm
DATA ENTRY LSB 00100110(26H)
DATA VALUE 0lllllll
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME
00H 00H mmH --- PITCH BEND SENSITIVITY
01H 00H mmH llH MASTER FINE TUNE
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
02H 00H mmH --- MASTER COARSE TUNE
28H - 40H - 58H (-24 - 0 - +24 semitones)
7FH 7FH --- --- RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.
(3-4) NON-REGISTERED PARAMETER NUMBER
There are no applicable parameters.
These are transmitted to the Plug-in board.
(3-5) SYSTEM REAL TIME MESSAGES
STATUS 11111110(FEH)
Transmitted at every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played is forcibly turned off.
(3-6) SYSTEM EXCLUSIVE MESSAGE
F0H 7EH 7FH 09H 01H F7H
The PLG100-XG Plug-in board installed to the instrument, will receive this message when the instrument is in the
Song/Pattern mode and SYSTEM Receive GM/XG is set to on. The Part values will be reset according to the
SYSTEM Internal Part settings.
The internal tone generator block will receive this message when the instrument is in the Song/Pattern mode.
F0H 7EH 0nH 06H 01H F7H
("n" = Device No. However, this instrument receives under "omni.")
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
dd; Device Number Code
MOTIF ES6: 69 05
MOTIF ES7: 6A 05
MOTIF ES8: 6B 05
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value "mm" is used to set the master volume (the value "ll" should be ignored).
11110000 F0
01000011 43
0001nnnn 1n
01001100 4C
0aaaaaaa 0
0aaaaaaa 0
0aaaaaaa 7E
0 0
11110111 F7
The PLG100-XG Plug-in board installed to the instrument, will receive this message when the instrument is in the
Song/Pattern mode and SYSTEM Receive GM/XG is set to on. The Part values will be reset according to the
SYSTEM Internal Part settings.
The internal tone generator block will not receive this message.
Be aware that executing this message takes about 170 ms, and that an appropriate interval must be allowed before
executing the subsequent message.
11110000 F0
01000011 43
0001nnnn 1n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
See the following MIDI Data Table for Address and Byte Count.
66
Data List
n = 0 – 15 CHANNEL NUMBER
p = RPN LSB
(Refer to the table as shown below.)
q = RPN MSB (Refer to the table as shown below.)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 24 semitones)
Exclusive Status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
11110000 F0
01000011 43
0000nnnn 0n
01111111 7F
00000000 00
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
See the following BULK DUMP Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data
and Check sum itself are added.
11110000 F0
01000011 43
0010nnnn 2n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following DUMP REQUEST Table for Address and Byte Count.
11110000 F0
01000011 43
0011nnnn 3n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address.
(4) SYSTEM OVERVIEW
(Keyboard, Sequencer and Tone Generator)
MIDI IN/OUT = MIDI
SEQ KBD
Local Sw
TG
MIDI IN/OUT = USB or mLAN
SEQ KBD
Local Sw
TG
Although three types of note on/note off data, received via MIDI, played by the internal sequencer and played on the
keyboard will be distinguished, the other controllers (channel messages) equally affect the entire notes.
ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.
ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Byte Count
Byte Count
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
End of Exclusive
To USB/mLAN
From USB/mLAN

MIDI Out

MIDI In
To USB/mLAN
From USB/mLAN
Thru Port
MIDI Out
MIDI In