GE 19297 Installation Instructions

Wireless Doorbell
Installation instructions
Required Tools: Small flat blade screwdriver, #2 Phillips Screwdriver, and 1/16" and
3/32" drill bit (not included).
The wireless doorbell kit has two components:
Push Button (Transmitter) Figure 1
Push
button
Push flat blade screwdriver into
the slot to open the cover
Doorbell (Receiver) Figure 2
volume pairing
Installing battery in push button (transmitter)
1. Remove the front cover of the push button housing by pushing a flat blade screwdriver
into the slot at the bottom of the push button housing (See Figure 1).
2. Install the CR2032 battery (included) with the positive (+) side up.
3. Keep the front cover off the push button until melody selection is complete.
NOTE: The doorbell and push button(s) have been electronically paired during production.
Once the battery is installed in the push button and doorbell receiver, press the push
button(s) to ensure that the push button(s) cause the doorbell to operate.
IF doorbell DOES NOT SOUND, SEE TROUBLESHOOTING.
Melody Selection Setting (your doorbell will have either 2 or 8 melodies)
Select the melody by pushing the Melody Selection Button located inside the push button
housing (See Figure 1). Press and release the melody selection button until you hear the
Table 1 - 2 Melody Doorbell
1 Dingdong
2 Westminster
Table 2 - 8 Melody Doorbell
1 Dingdong
2 Westminster
3 Knocks (3 times)
desired melody. Tables 1 and 2 show the order the melodies will be heard.
The last melody played will be your selected doorbell melody.
Volume Adjustment
There are four volume settings on this doorbell.
1. To adjust the volume, press and release the pairing button on the doorbell or press the
push button to play the melody.
2. While melody is playing, press and release the volume button on the doorbell
to select the desired sound level.
Push button (transmitter) mounting instructions
NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of
transmission. Do not mount in an area exposed to direct rain. Push buttons are typically
mounted at the same height as the door knob or handle (between 36" and 44"
above the floor).
Permanent push button (transmitter) mounting instructions
1. Remove the front cover of the push button (See Figure 1).
2. Before mounting, choose a mounting location that is no further than 150 feet from
the doorbell unit location. Place the push button where you would like to mount and
test with the doorbell as close to its final location as possible. If it works, continue with
mounting the button. If it does not work, see TROUBLESHOOTING.
3. Hold the back plate of the push button in the selected location with the arrow on the
back of the back plate pointing up.
4. Using the 1/16" drill bit, drill a hole through the back plate of the push button
(See Figure 3 — Mounting hole locations) and into the surface of the selected location.
5. Secure with the two screws provided.
6. Press front housing onto back cover.
7. Test operation. If doorbell does not work, see TROUBLESHOOTING.
Push
button
Melody
selection
button
Battery
compartment
Keyhole
slots
4 Fanfare 7 Patriotic
8 Tango
5 Mozart
6 Good Vibes
Temporary push button (transmitter)
mounting instructions
1. Clean the mounting location for the push button with
a mixture of 50% water and 50% isopropyl alcohol.
2. Remove protective backing from one side of the
adhesive pad and attach it to the back plate of the
push button.
3. Remove protective backing from the other side of the
adhesive pad and press the back plate to the cleaned
mounting location. Hold in place for a few seconds to
allow for a secure bond.
Doorbell (receiver) mounting instructions
NOTE: Avoid mounting on metal surfaces, as it may
result in a reduced range of reception.
1. Select doorbell mounting location.
2. Using the doorbell mounting template on the
package, insert card and drill two holes with 3/32"
drill bit in marked keyhole slot locations
(See Figure 2).
3. Insert the two included 3x25mm screws into the holes, with the screw heads extending
Mounting
hole
about ¼" from mounting surface.
locations
4. Place the doorbell unit's keyhole slots over the screws and press down on the doorbell
unit to secure it.
Extra doorbell receivers and push buttons available at www.byjasco.com.
Troubleshooting
If the doorbell does not work:
1. Make sure push button switch is pressed down and held for at least 1 second.
2. Verify battery installation is correct, noting polarity.
3. Try a fresh battery in push button.
4. Make sure doorbell is no further than 150 feet away from push button.
5. Ensure push button is not mounted on metal, near metal studs or near the floor.
6. Try a new location for the doorbell.
7. If the doorbell and push button(s) do not operate, repeat the electronic pairing process of
the push button(s) to the doorbell in steps A-F below:
A. To clear settings: press and hold the pairing button on the bottom of the doorbell
while installing the third battery.
B. Once the last battery is installed, release the pairing button.
C. Press and hold the pairing button again. You will
hear the "Dingdong" melody twice, and then the
double beep to alert you the doorbell is ready to
pair with the push button. Release the pairing
button.
D. Press and release the push button (See Figure 4).
You will hear one beep letting you know the doorbell
accepted the signal.
E. Wait 10 seconds and you will hear the double beep
again to alert you the doorbell is now paired with the push button.
F. Press the push button to test.
Functional range may be adversely affected by one or more of the following factors:
weather, radio frequency interference, low transmitter battery or obstructions between the
transmitter and receiver.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• BATTERIES MAY LEAK HARMFUL LIQUIDS OR
IGNITABLE MATERIALS OR EXPLODE CAUSING
INJURY AND PRODUCT DAMAGE
• DO NOT MIX OLD AND NEW OR OTHER
BATTERY TYPES
• REPLACE ALL BATTERIES AT THE SAME TIME
• REPLACE EXHAUSTED BATTERIES
IMMEDIATELY
• REMOVE BATTERIES IF PRODUCT IS TO BE
UNUSED FOR EXTENDED OF TIME
MADE IN CHINA
GE is a trademark of General Electric Company and is under
license by Jasco Products Company LLC, 10 E. Memorial Rd.,
Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited
warranty. Visit www.byjasco.com
for warranty details. Questions? Contact
us at 1-800-654-8483 between
7:00AM—8:00PM CST.
Figure 3
Push
button
Melody
selection
button
Battery
compartment
Figure 4
Push
button
Push flat blade screwdriver into
the slot to open the cover
• Consult the dealer or an experienced radio/TV
technician for help.
For technical support, contact Jasco Products
Company at 1-800-654-8483
or www.byjasco.com.
Mounting
hole
locations
Push
button
Melody
selectio
button
Battery
compar
19248
19297
19303
30393
V10
3/6/18