キャップ A を取り外し、キャップ B に付け替える。 ネジ A を使って、 図のようにして、 両面に L 型金具を 取り付ける。 キャップ A を取り外すとき キャップ A の頭を内側に押し付けながら、L レンチ を使って取り外します。 キャップ A 同様にして、もう一方の側面に L 型金具を取り付け L レンチ る。 インナーレールを取り付ける ネジ D を使って、インナーレールを取り付ける。 キャップ B を取り付けるとき キャップ B に止めネジを入れ、フロントパネルの軸 インナーレール の...
Page 6
レールアセンブリーをブラケットに取り付 ご注意 ける ここでは、ネジを固定しないでください。レールア センブリーを取り付けた後、本機が取り付けできる レールアセンブリーをブラケットにのせて、ラック ことを確認してから固定します。 の奥まで差し込み(1) 、レールアセンブリーからス ライドレールを手前に引き出す(2) 。 ブラケット レールアセンブリー ブラケット ネジ B スライドレール ネジ穴を合わせる ブラケットのネジ穴とレールアセンブリーのネジ穴 を合わせ、ネジ C を使ってレールアセンブリーの後 ろ側を止める。 ラックの奥の柱にレールアセンブリーを当てておく と、位置が決めやすくなります。レールの長さが足 りないときは、ブラケットの長穴を使ってネジを止 めてください。 ブラケット 合わないときは長穴を 使う ネジ C 同様にして、図のように、ブラケットを仮止めする。 ブラケットの向きと高さをまちがえないように気を つけてください。 S ネジ レールアセンブリに当てる メモ ブラケットの S ネジを使うと、ナットが不要になり ますので、作業がしやすくなります。...
This Rack Mounting Kit can be used to mount the AIT library in an EIA Standard 19-inch rack. For installation After opening the package, make sure that all of the instructions, contact Sony Service Support Center. following items are present. Contact your dealer if (Charges apply.) anything is missing.
Preparing the Library Preparation Mount the L-shaped brackets and inner rails on the library. In order to mount the AIT library, first mount the rails and brackets on the library and rack. Mounting the B Caps and L-shaped Before beginning work, always be sure to press the Brackets power standby switch on the front panel of the AIT After you have removed the front panel and replaced the...
Remove the A caps and replace them with the B Use two A screws to mount an L-shaped bracket on caps. the side of the library as shown in the diagram. Removing the A Caps While pressing the A cap inward with your finger, use the Allen wrench to loosen the set screw and remove it.
Page 13
Using two B screws, hand tighten the bracket to the Mounting the Rail Assemblies on the rack. Brackets Caution Place a rail assembly in one set of brackets, slide the rail assembly all of the way into the rack (1), and Do not tighten the screws completely.
Press the locking arm to release the lock, and then Mounting the AIT Library slide the library all of the way into the rack. in the Rack Locking arm Insert the library into the rack, and then secure the brackets. Caution With a single drive installed, the AIT library weighs approximately 18 kg/39.7 lbs.
Do not forget to tighten the B screws in the back of Removing the Library the rack. from the Rack B screw Caution With a single drive installed, the AIT library weighs approximately 18 kg/39.7 lbs. (With two drives installed, the AIT library weighs approximately 19 kg/ 41.9 lbs.) At least two people are needed in order to handle the Fastener...