Installing Your New Vcr; Connections - JVC HM-DB1U Instructions Manual

INSTALLING YOUR NEW VCR

Connections

Antenna or Cable
Coaxial Cable
Flat Feeder
Transformer
AC Outlet
(not supplied)
AC Power
Cord
Back of VCR
To [AUDIO OUT]
To [VIDEO
OUT]
Audio
Cable
Video
(not
Cable (not
supplied)
supplied)
or
Antenna
or Cable
*S-Video
for digital
Cable (not
broadcast
supplied)
To To
Audio Video
Input Input
Connectors Connector
To S-Video
Input Connector
To 75 Ω terminal
To i.LINK Input/
Integrated HDTV
Output Connector
NOTES:
● Your TV must have audio/video input connector for the
connection to the VCR.
● Even if you are using audio/video cables to connect your VCR
to your TV, you must also connect it using the RF cable. This
will ensure that you can record one show while watching
another ( pg. 25).
● To make the most of the Super VHS picture performance we
recommend that you use an S-Video cable to connect your
VCR to a TV with an S-Video input connector.
Matching
To
[ANTENNA
IN]
(Antenna or
cable input)
VHF/UHF
ANTENNA
IN
OUT IN
S VIDEO S VIDEO
IN(L-1)
i.LINK IN/OUT i.LINK IN/OUT
ANTENNA
S200 S200
OUT
R AUDIO L VIDEO R AUDIO L VIDEO
D THEATER
REGION 1
IN(L-2)
To
[S VIDEO
OUT]
To
[ANTENNA
OUT]
RF Cable
(supplied)
i.LINK cable
(supplied)
Basic Connection
1
Check contents
Make sure the package contains all of the
accessories listed in 'SPECIFICATIONS' (
2
Situate VCR
Place the VCR on a stable, horizontal surface.
3
Connect VCR to TV
The following connections are required.
1 Disconnect the TV antenna from the TV.
2 Connect the TV antenna cable to the VCR's
[ANTENNA IN] terminal.
3 Connect the supplied RF cable between the
VCR's [ANTENNA OUT] terminal and the TV's
antenna input terminal.
4 Connect an audio/video cable between the
VCR's [AUDIO/VIDEO OUT] connectors and
the TV's audio/video input connectors.
5 Connect an i.LINK cable between the VCR's
[i.LINK IN/OUT] connector and the TV's i.LINK
input/output connector.
Digital Set Top Box Connection
To
● If you are using a HD Ready TV, see 'Digital Set Top
[i.LINK
IN/
Box Connection' on page 8.
OUT]
S-VIDEO Connection
*
● If your TV has S-Video input terminals, use an S-
Video cable to connect between the VCR's [S VIDEO
OUT] connector and the TV's S-Video input
connector.
4
Connect VCR to power source
Connect the AC power plug to the AC outlet.
● The clock and tuner channels will automatically
be set when the antenna is connected and when
the AC power cord is first connected to an AC
power outlet ( pg. 9).
(If [Auto] or channel numbers are displayed on the
front display panel before the VCR is turned on, the
clock and tuner channels are being set automatically.
Wait until the clock time is displayed on the front
display panel before turning on the VCR.)
5
Final preparation for use
Turn on the VCR.
● You can now perform basic playback
( pg. 15) or basic recording (
● To operate the VCR with your TV using the S-VIDEO
connection, set your TV to the AV mode using the TV's
Remote.
You can also use the TV/VCR button on the VCR's Remote to
set your TV to the AV mode (
● Use the commercially available i.LINK cable (4-pin, S400,
below 3m). If the cable used is above 3m, this VCR will not
fully maximize its performance.
● For full identification of the VCR's rear panel, refer to the
Index ( pg. 58).
7
EN
pg. 61).
pg. 23).
pg. 46).