Toro Sand Pro 2040Z Operator's Manual
Flex tooth rake, traction unit
Hide thumbs
Also See for Sand Pro 2040Z:
- Service manual (130 pages) ,
- Operator's manual (60 pages) ,
- Operator's manual (56 pages)
Related Manuals for Toro Sand Pro 2040Z
Summary of Contents for Toro Sand Pro 2040Z
- Page 1 Form No. 3382-548 Rev B Flex Tooth Rake Sand Pro ® 2040Z Traction Unit Model No. 08716—Serial No. 314000001 and Up G024504 *3382-548* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
3 Connecting the Center Assembly and the Side product properly and safely. Assemblies............4 You may contact Toro directly at www.Toro.com for product 4 Connecting the Drawbar to the Rake......5 and accessory information, help finding a dealer, or to register 5 Attaching the Boom .......... -
Page 3: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Adjust the tire pressure. Remove the shipping board from the – No parts required machine. Center assembly Right-side assembly Left-side assembly Connect the center assembly and the Bolt (3/4 x 3-1/2 inches) -
Page 4: Adjusting The Tire Pressure
Adjusting the Tire Pressure No Parts Required Procedure G023667 For the rake to work properly, it is important Figure 4 for the machine to have the correct tire pressure. Ensure that the tire pressure is 48 kPa (7 psi) (Figure 3). 2. -
Page 5: Connecting The Drawbar To The Rake
6. Align a cable guard over the pivot hole, and secure them with a bolt (3/4 x 3-1/2 inches) and a locknut (3/4 inch), torqued to 163 to 217 N-m (120 to 160 ft-lb); refer to Figure 6. Note: Ensure that the side assembly pivots freely. Slightly loosen the nut and bolt if necessary. -
Page 6: Attaching The Boom
3. Insert the bolt (3/4 x 3-1/2 inches) to secure the drawbar to the pivot assembly. 4. Install the locknut (3/4 inch) onto the bolt, and torque it to 163 to 217 N-m (120 to 160 ft-lb). Attaching the Cables Parts needed for this procedure: Cable Attaching the Boom... -
Page 7: Attaching The Stop-Chain Assembly
G023804 Figure 11 1. Flange nut (5/16 inch) 4. Drawbar G023805 2. Drawbar bracket 5. U-bolt Figure 10 3. Center tab 1. Flange nut (5/16 inch) 4. Cable 2. Boom 5. Cable support 2. Install the U-bolt and secure it with 2 flange nuts (5/16 3. -
Page 8: Product Overview
Product Overview Operation Installing and Removing the Weights The flex tooth rake requires 4 weights, which are included with the machine. Always ensure that your machine has the appropriate number of weights. Refer to the following table for how many weights are required on the front of the machine: Attachment Number of weights required... -
Page 9: Installing The Rake To The Machine
Connecting the Drawbar to the Frame weights and securing it with the nut; refer to the Light Kit Installation Instructions. Hitch 1. Align the rod end of the drawbar to the frame hitch Installing the Rake to the (Figure 15). Machine Connecting the Chains to the Attachment Lift... -
Page 10: Adjusting The Pivot Stop Bolts
Connecting the Frame Bracket Adjusting the Pivot Stop Bolts 1. Remove the nut and the bolt securing the muffler 1. Pivot the rake to 1 side. The stop bolt should contact shield to the back of the machine (Figure 16). the drawbar when the rake is 51 mm (2 inches) away from the tire (Figure 18). -
Page 11: Inspecting The Raking Pattern And Adjusting The Lift-In-Turn System
Note: Use a wrench on the square neck of the bolt to prevent the bolt from spinning. 4. Repeat the procedure for the other stop bolt. 5. Ensure that the rake does not contact the tires throughout the range of motion. Inspecting the Raking Pattern and Adjusting the Lift-in-turn System... -
Page 12: Raising And Lowering The Rake
WARNING If you drive the machine without an attachment installed, it can tip over and injure someone or damage property. Do not drive the machine without a Toro-approved attachment installed. 1. Disconnect the drawbar from the frame hitch. G024510 Figure 23 2. - Page 13 however, it is important to vary the raking pattern regularly to reduce the chance of creating a washboard effect. G003409 Figure 25 1. Enter a trap straight into 2. Exit a trap at a right angle the long dimension in a in a level area.
-
Page 14: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action There is a teardrop-shaped area that 1. The lift-in-turn cables are not adjusted 1. Adjust the lift-in-turn cables. remains ungroomed. properly. 2. The pivot stop bolts are not adjusted 2. Adjust the pivot stop bolts. properly. - Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.