Valon 5009 Quick Start Manual

5009 Quick Start Guide
Step 1: Power Supply Connection Step 1: Power Supply Connection
You are going to need a 6Vdc ±0.5V at going to need a 6Vdc ±0.5V at 600mA power supply. Use the supplied red-black Hirose cable to
connect to your power supply. Connect it and you should see two blue LEDs illuminating through the
label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on
Source 1 and 2480MHz on Source 2. Source 1 and 2480MHz on Source 2.
See "Hints and Kinks – Power Supplies"
Step 2: USB connection
Connect the provided USB cable to your 5009 and host computer. Your computer should recognize it as Connect the provided USB cable to your 5009 and host computer. Your computer
a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP
(virtual com port) driver. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip river. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip river. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip
and run).
Step 3: Terminal Program
You will need a terminal program to change your 5009 settings. Just about any terminal program will You will need a terminal program to change your 5009 settings. Just about any terminal program will You will need a terminal program to change your 5009 settings. Just about any terminal program will
work. We have provided 5000term
correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None, correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None, correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None,
1, None.
Step 4: Synthesizer Settings
After launching your terminal program, press the Enter key a few times and check to see that you get a After launching your terminal program, press th
cursor like this: "-1->", if you do, you have successfully established communications with your 5009. >", if you do, you have successfully established communications with your 5009. >", if you do, you have successfully established communications with your 5009.
Type help to get the help menu
control-c will exit program.
control-f will increase the baud rate to 115200.
control-r will reset the synthesizer to factor default settings.. r will reset the synthesizer to factor default settings..
Consult the Valon 5009 Operations Manual Valon 5009 Operations Manual for more information on the use of these commands.
Note that as of this date, not all commands in the Operations Manual are available. As these commands Note that as of this date, not all commands in the Operations Manual are available
become available, we will notify you and you will be able to download the updated *.bin files. You become available, we will notify you and you will be able to download the update
also use the 5000term.exe terminal program to load the *latest*.bin files.
For the latest 5009 Downloads: http://www.valontechnology.com/5009users/5009.htm
Above all, if you have trouble or need help just Above all, if you have trouble or need help just contact us.
Stuart Rumley
650-369-0575
stuart@valontechnology.com
Valon Technology 5009 Quick Start Guide 5009 Quick Start Guide
Connect it and you should see two blue LEDs illuminating through the Connect it and you should see two blue LEDs illuminating through the
Power Supplies" on back of this document.
5000term.zip . Unzip and running 5000term.exe will automatically find the
ate to 115200.
for more information on the use of these commands.
.exe terminal program to load the *latest*.bin files.
http://www.valontechnology.com/5009users/5009.htm http://www.valontechnology.com/5009users/5009.htm
e Enter key a few times and check to see that you get a
1
black Hirose cable to
should recognize it as
.exe will automatically find the
As these commands
*.bin files. You can
06/27/2018