HIKVISION DS-2CD23 Series Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD23 Series
  6. Quick start manual

HIKVISION DS-2CD23 Series Quick Start Manual

Network turret cameras
Hide thumbs Also See for DS-2CD23 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Quick Start Guide
DS-2CD23xxxx-xx Network Turret Cameras

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD23 Series

Summary of Contents for HIKVISION DS-2CD23 Series

  • Page 1 Quick Start Guide DS-2CD23xxxx-xx Network Turret Cameras...
  • Page 2 Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS,” WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
  • Page 3 device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 4 Cautions: Injury or equipment damage may occur if any of the cautions are neglected. • Warnings Cautions Follow these safeguards Follow these precautions to prevent serious injury to prevent potential injury or death. or material damage. Warnings Proper configuration of all passwords and other security settings is the responsibility of the •...
  • Page 5 To avoid heat accumulation, good ventilation is required for the operating environment. • Keep the camera away from liquids while in use. • While in delivery, pack the camera in its original packing or packing of the same material. • Regular Part Replacement: A few equipment parts (e.g., electrolytic capacitor) must be replaced •...

  • Page 6: Table Of Contents

    Table of Contents Appearance ............................7 Type I ..............................7 Type II ..............................8 Type III ............................... 9 Type IV ............................. 10 Installation ............................10 Ceiling Mounting ..........................11 Type I ............................11 Type II ............................15 Type III ............................17 Type IV ............................

  • Page 7: Appearance

    1 Appearance This turret camera series has four appearance types. Type I Figure 1, Overview of Type I Turret Camera Table 1-1 Description Description Description Trim Ring Camera Enclosure Power Cord Mounting Base 10M/100M Self-Adaptive Ethernet Interface QSG DS-2CD23xxxx-xx Turret 051420NA...

  • Page 8: Type Ii

    Type II Figure 2, Overview of Type II Turret Camera Table 1-2 Description Description Description Trim Ring 4 Camera Enclosure 5 Power Cord Mounting Base 6 10M/100M Self-Adaptive Ethernet Interface QSG DS-2CD23xxxx-xx Turret 051420NA...

  • Page 9: Type Iii

    Type III Figure 3, Overview of Type III Turret Camera Table 1-3 Description Description Description Trim Ring Audio Output Enclosure 1-ch Alarm Input and 1-ch Alarm Output Mounting Base RST (Reset) Button Camera Memory Card Slot Power Cord 10M/100M Self-Adaptive Ethernet Interface Press the Reset button for approximately 10s when the camera is powering on or NOTE: rebooting to restore the default settings, including the user name, password, IP...

  • Page 10: Type Iv

    Type IV Figure 4, Type IV Turret Camera Table 1-4 Description Description Description Trim Ring Power Cord Enclosure 10M/100M Self-Adaptive Ethernet Interface (PoE) Mounting Base RST (Reset) Button Camera Memory Card Slot NOTES: For type IV cameras, the memory card slot and reset button locations may differ by model.

  • Page 11: Ceiling Mounting

    Make sure that the wall is strong enough to withstand four times the weight of the camera and the • bracket. For cameras that support IR, make sure that there is no reflective surface too close to the camera • lens.
  • Page 12 Figure 6, Drill Template NOTE: There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet as shown below. Figure 7, Side Outlet QSG DS-2CD23xxxx-xx Turret 051420NA...
  • Page 13 NOTE: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic, and route the cables through the hole. 3. Affix the mounting base to the ceiling with the supplied expansion screws. Figure 8, Secure the Mounting to the Ceiling 4.
  • Page 14 Figure 10, Loosen Lock Screw 2). Rotate enclosure to adjust the pan angle; rotate camera to adjust the tilt angle. Figure 11, Adjust the Lens 3). Tighten the lock screw to fix the optimum surveillance angle. 6. Attach the trim ring to the camera and rotate the trim ring clockwise to secure it. Figure 12, Install the Trim Ring QSG DS-2CD23xxxx-xx Turret 051420NA...

  • Page 15: Type Ii

    Type II 1. Disassemble the camera. 1). Rotate the enclosure counterclockwise to remove it from the camera. 2). Separate the camera, the mounting base, and the trim ring. Figure 13, Disassemble the Camera 2. Drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 14, Drill Template QSG DS-2CD23xxxx-xx Turret 051420NA...
  • Page 16 NOTE: There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below. Figure 15, Side Outlet NOTE: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling.

  • Page 17: Type Iii

    Figure 17, Adjust the Lens 7. Attach the trim ring to the camera, and rotate it clockwise to secure it. Figure 18, Install the Trim Ring Type III 1. Disassemble the camera. 1). Rotate the trim ring counterclockwise to take it off of the camera. 2).
  • Page 18 2. Install the memory card. 1). Locate the microSD/RST cover on the side of the camera. MicroSD/RST Cover Figure 20, Micro SD/RST Cover 2). Take off the cover, and insert the microSD card into the card slot. Figure 21, Memory Card Slot 3).
  • Page 19 Figure 22, Drill Template 4. Affix the mounting base to the ceiling with two supplied expansion screws. Figure 23, Fix Mounting Base to Ceiling 5. Connect the corresponding power/network cable. Refer to section 2.3 for waterproof accessory installation if the camera is installed outdoors. 6.

  • Page 20: Type Iv

    Figure 24, Install the Camera 7. Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle. Figure 25, Adjust the Lens 8. Attach the trim ring to the camera, and rotate the trim ring clockwise to secure it. Figure 26, Install the Trim Ring Type IV 1.
  • Page 21 3). Separate the camera and the enclosure. Figure 27, Disassemble the Camera 2. Install memory card. 1). Unscrew the memory card slot cover. 2). Insert the memory card. Figure 28, Install Memory Card 3). (Optional) to unmount the memory card, push it in to eject it. 4).
  • Page 22 Figure 29, Drill Template 5. Fix the mounting base to the ceiling with two supplied screws. Figure 30, Fix Mounting Base 6. Connect the corresponding power/network cable. Refer to section 2.3 for waterproof accessory installation if the camera is installed outdoors. 7.

  • Page 23: Mounting With Brackets

    Figure 31, Install the Camera 8. Adjust the surveillance angle of the camera. Secure the fixing screw after adjustment. Figure 32, Adjust Surveillance Angle 9. Attach the trim ring to the camera, and rotate the trim ring clockwise to secure it. Figure 33, Install Trim Ring Mounting with Brackets This camera series supports mounting with a wall mounting bracket and a pendant mounting...

  • Page 24: Wall Mounting

    Wall Mounting A wall mount is not included in the package. You must purchase one separately if you use this mounting method. 1. Mark the screw holes on the desired mounting location. Figure 34, Dimensions of Typical Wall Mounting Bracket 2.

  • Page 25: Pendant Mounting

    Figure 35, Fix Mounting Base 6. Connect the corresponding power/network cable. Refer to section 2.3 for waterproof accessory installation if the camera is installed outdoors. 7. Install the camera and the enclosure to the mounting base, adjust the surveillance angle, and fix the trim ring. NOTE: Refer to the specific camera type’s corresponding ceiling mounting steps.
  • Page 26 Figure 37, Fix Pendant Mount 4. Disassemble the camera. NOTE: Refer to step 1 of the specific camera type’s ceiling mounting section. 5. Fix the mounting base to the pendant mounting bracket cap with three supplied self- tapping screws. Figure 38, Fix Mounting Base 6.
  • Page 27 Figure 39, Install the Cap 7. Connect the corresponding power/network cable. Refer to section 2.3 for waterproof accessory installation if the camera is installed outdoors. 8. Install the camera and the enclosure to the mounting base, adjust the surveillance angle, and fix the trim ring. NOTE: Refer to corresponding steps in each camera type’s ceiling mounting section.

  • Page 28: Network Cable Waterproof Accessory Installation

    Network Cable Waterproof Accessory Installation Purpose If the camera is installed outdoors, you can use the waterproof accessory for the network cable after the camera is secured on the installation surface. Figure 41, Waterproof Accessory Components Table 2-1 Components No. Components Camera’s Network Interface Socket O-Type Gasket Network Plug...

  • Page 29: Special Instructions For Attaching Camera To A Cb140Pt Conduit Base

    Figure 42, Waterproof Accessory Installation 2.4 Special Instructions for Attaching Camera to a CB140PT Conduit Base Some cameras (e.g., DS-2CD23x5G1, DS-2CD23x7G1, DS-2TD1217-2/3/6/V1, DS-2CD23x6G2, DS- 2CD23x6G1, DS-2CD23x7G1, DS-2CD23x6G2, and others) require the following steps to install a CB140PT conduit base accessory. 1.

  • Page 30: Setting The Network Camera Over The Lan

    Figure 43, Attaching a CB140PT Conduit Base to a Select Camera Model (Typical) 3 Setting the Network Camera over the LAN NOTE: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 31: Wiring

    3.1 Wiring Connect the camera to the network according to the following figures. Figure 44, Connecting Directly Figure 45, Connecting via a Switch or a Router 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use it.

  • Page 32: Activation Via Sadp Software

    1. Power on the camera. 2. Connect the camera to your computer or the switch/router which your computer connects to. 3. Input the IP address into the Web browser’s address bar and press Enter to enter the activation interface. NOTES: The default IP address of the camera is 192.168.1.64.
  • Page 33 Follow these steps to activate the camera. 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Figure 47, SADP Interface NOTE: The SADP software supports activating the camera in batches. Refer to the SADP software user manual for details.

  • Page 34: Modifying The Ip Address

    Modifying the IP Address Purpose To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification.

  • Page 35: Accessing Via Web Browser

    4 Accessing via Web Browser System Requirements Operating System: Microsoft Windows XP SP1 and above version • CPU: 2.0 GHz or higher • RAM: 1 GB or higher • Display: 1024 × 768 resolution or greater • Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla •...

  • Page 36: Operating Via The Hik-Connect App

    Figure 50, Download Plug-in 6. Re-open the Web browser after the plug-in installation, and repeat steps 2 to 4 to login. For detailed configuration instructions, refer to the network camera user manual. NOTE: 5 Operating via the Hik-Connect App Purpose Hik-Connect is a mobile device application.

  • Page 37: Enable Hik-Connect Service Via Web Browser

    NOTE: The verification code is required when you add the camera to the Hik-Connect app. 3. Click and read the “Terms of Service” and “Privacy Policy.” 4. Confirm the settings. Enable Hik-Connect Service via Web Browser Before You Start Activate the camera before enabling the service. Refer to Chapter 3.2. 1.

  • Page 38: Adding Camera To Hik-Connect

    Adding Camera to Hik-Connect Before You Start You need to enable the Hik-Connect service on the camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. 1. Use a network cable to connect the camera to a router if the camera does not support Wi-Fi. Figure 53, Connect a Router NOTE: After the camera connects to the network, wait one minute before attempting any...

  • Page 39: Initializing The Memory Card

    Initializing the Memory Card 1. Check the memory card status by tapping on Storage Status in the Device Settings interface. 2. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
  • Page 40 QSG DS-2CD23xxxx-xx Turret 051420NA...

Table of Contents