Related Manuals for CanDock G2 JETSLIDE
Summary of Contents for CanDock G2 JETSLIDE
- Page 1 Modular floating systems ARE YOU READY TO JETSLIDE system -OWNER’S MANUAL- www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR. 819 847-2599 Sherbrooke (Qc) J1N 0G2 T.FREE|S. FRAIS 1 888 547-2599 FAX|TÉLÉC. 819 847-3250...
- Page 2 All distributors are required and responsible to provide theoretical and practical training to clients on the complete use of the different dock systems. Candock inc. can not be held responsible in any way for any damages resulting from the fact that the client has not received adequate training.
- Page 3 All distributors are held responsible for giving training to their customers on the complete use of the system (theoretical and practical) with the watercraft of their customer. Candock Inc. will not be held responsible for any damages resulting from the fact that the operator did not receive the adequate training.
- Page 4 #1 of the second JETSLIDE. OVERVIEWS MINIMAL CONFIGURATION PWC JETSLIDE SYSTEM <800LBS -1 x G2 JETSLIDE -14 x G2 CUBES -12 x G2 CONNECTING PINS -2 x CANDOCK SLIDING NUTS -14 x CANDOCK LUG CONNECTORS -14 x CANDOCK NUTS...
- Page 5 Modular floating systems G2 JETSLIDE ( SEQUENCE ) RIGHT SIDE ASSEMBLY IMPORTANT NOTICE 1 CANDOCK SPACER (LAYERS 4) These sketches imply that the the cubes “PLUGS” are oriented toward the front of the JETSLIDE system. 2 CANDOCK SPACERS Other “PLUGS” orientations will simply interchange (LAYERS 3 AND 4) the positions of the differents cube tabs and spacers.
- Page 6 Modular floating systems G2 JETSLIDE ( SEQUENCE ) ASSEMBLY WITH “CLOSED” CORNER CUBE * Make sure 5a is in place before tightening 5b. TAB# TAB# TYPICAL APPLICATION Proceed to assembly following regular G2 CORNER CUBE procedures while Based on the same...
- Page 7 Modular floating systems G2 JETSLIDE ( SEQUENCE ) ASSEMBLY TIPS: IMPORTANT NOTICE -Assemble on a flat surface rather than water. It will be easier that way. - Assemble the cubes around the JetSlide. If you attach it to a dock, make sure the plugs are facing the SAME DIRECTION.
- Page 8 JetSlide. An installation with only one row is possible, but there is a risk of damaging the machines and, therefore, the resulting damages will not be covered by the manufacturers warranty. Contact Candock for more information. 3-The handling of several JetSlides assembled in series by lifting (for winterizing by using a crane for example) is strictly forbidden.
- Page 9 10-All distributors are held responsible for giving training to the customers on the complete use of the system, theoretical and practical with the watercraft of the customer. Candock Inc. will not be held responsible for any damages resulting from the fact that the operator did not receive the adequate training.
- Page 10 Once filled, the tank’s surface will float right above water so that it will easily be slipped underneath the dock later on. www.candock.com candock@candock.com 9441, Bourque Blvd.
- Page 11 After the tank has been perfectly aligned, complete the procedure by firmly screwing the nut and washer assembly on the threaded rod, without exaggerating. P.10 www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR.
- Page 12 *We strongly suggest to pair your battery to a charge keeper of a solar panel to insure sufficient power to your battery, at all time. Simply ask your Candock distributor if you should need additional information on the subject. 12-The final step of your assembly consists of placing a fully charged deep cycle “marine grade”...
- Page 13 1- INFLATE Once your boat is on the JetSlide (See instruction for use of Candock JetSlides), stop the engine and go on the dock. For security reasons, it is always better to secure the boat to your Candock dock using a rope. Open the Control Box and position the valve system to it’s “INFLATE”...
- Page 14 These should always be used when recommended and the use of bars other than those provided by Candock is prohibited unless written permission from Candock. The first bar is always installed between the 1st and 2nd row of cubes in the back.
- Page 15 You'll notice that the installation of in line JetSlides leaves a gap (in red on the attached image) at the V of JetSlide. To fill the gap you must install a V-plate which can be simply screwed under the JetSlide. It is very important for the safety of users. Candock Inc. disclaims all liability for accidents if the V plate is not installed.
- Page 16 15/16” key wrench Key for nut Ratchet key for nut + ratchet tool Needed accesories (sold separately) : 5 TO 9 CANDOCK LUG CONNECTOR JETSLIDE 5 TO 9 CANDOCK SLIDING NUTS 4 TO 8 CANDOCK SPACERS Depending on plate size. OVERVIEWS These Safety Plates, available in 3 different sizes, have been created to accomodate intermediary boat lenght.
- Page 17 9/16” key wrench Key for nut Ratchet key for nut + ratchet tool Accesories included with the winch 1 CANDOCK LUG CONNECTOR 1 CANDOCK NUT 1 Aluminum mounting bracket 1 Pulling winch ( 400 lbs capacity ) equipped with a 15 ‘ strap and 1 hook.
- Page 18 1 fastening carabiner 1 Shackle Other needed accesories (sold separately) 4 CANDOCK LUG CONNECTOR 4 CANDOCK NUT 1 ANCHORING RING OVERVIEWS Sometimes, for a boat less than 1360kg / 3000lbs, a winch may be required to put the boat afloat.
- Page 19 NOTES: MULTIPLE JETSLIDES ASSEMBLY -Always keep the system symmetrical left/right. -In doubt, please refer to your Candock representative. -These guidelines are imperative to insure full warranty coverage -Although we advocate 2 rows of cubes in between each JETSLIDE, a multiple...
- Page 20 FLOATING STRUCTURE AS THEY -In doubt, please refer to -If placed at position #2, DO NOT ALLOW WATER LEVEL your Candock representative. steel cable are not needed. FLUCTUATION *Beware of water lavel variation -These guidelines are imperative limitations +/- 2’ ( .75m ).
- Page 21 JETSLIDE through the dock leg support, -In doubt, please refer to then the cube tabs and then into your Candock representative. the sea bed. -Always keep the anchoring symmetrical left/right. -These guidelines are imperative to insure full warranty coverage -In doubt, please refer to your Candock representative.
- Page 22 4000 - 5000 lbs 8 -9 25,5 - 30 2270 - 2730 kg 5000 - 6000 lbs 8 -9 25,5 - 30 P.21 www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR. 819 847-2599 1 888 547-2599 Sherbrooke (Qc) J1N 0G2 T.FREE|S. FRAIS FAX|TÉLÉC.
- Page 23 -Always leave a minimum of 1 regular cube between each G2 POST CUBE -These guidelines are imperative to insure full warranty coverage -In doubt, please refer to your Candock representative. P.22 www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR.
- Page 24 -These guidelines are imperative to insure full warranty coverage -In doubt, please refer to your Candock representative. P.23 www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR.
- Page 25 -Always keep the anchoring symmetrical left/right. -These guidelines are imperative to insure full warranty coverage -In doubt, please refer to your Candock representative. P.24 www.candock.com candock@candock.com 9441, Bourque Blvd. OFFICE|BUR. 819 847-2599...
- Page 26 JetSlide moves slightly forward when entering the unit and backwards when exiting the unit. This is why you need to check regularly the tightness of the chains to limit this movement. -These guidelines are imperative to insure full warranty coverage -In doubt, please refer to your Candock representative. P.25 www.candock.com candock@candock.com...
- Page 27 JETSLIDE SYSTEM FOR BOATS can also be added to an existing Candock system. Make sure that the dock is anchored well enough to resist the forward and backward movement generated by the watercraft when it enters or goes down the JetSlide.