Napoleon Alluravision Series Installation And Operation Manual

Napoleon Alluravision Series Installation And Operation Manual

Hide thumbs Also See for Alluravision Series:
Table of Contents

Advertisement

Available languages

Available languages

NEFL42CHS / NEFL50CHS / NEFL60CHS / NEFL74CHS
MULTIPLE PRODUCT CODES (LEAVE BLANK IF N/A)
NEFL42CHD / NEFL50CHD / NEFL60CHD / NEFL74CHD / NEFL100CHD
SAFETY INFORMATION
WARNING
!
FIRE OR EXPLOSION HAZARD
If the information in these instructions are
not followed exactly, a fi re or explosion may
result causing property damage, personal
injury, or loss of life.
- Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity of
this or any other appliance.
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
$10.00
ADD MANUAL TITLE
OPERATION MANUAL
INTERTEK
Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com
INSTALLATION AND
ADD BUTTON BATTERY WARNING IF APPLICABLE
This appliance has a remote that requires button
batteries that are hazardous to young children.
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
IF INSTALLATION + OPERATION, ADD SERIAL
CSA /
IF SEPARATE MANUALS, ADD "PLACE
LOGO
BARCODE LABEL ON THE OWNER'S MANUAL"
FRENCH PG.35
Alluravision™ Series
Product Name / Code
(MUST use title from Price Book)
(NEFL50CHD llustrated)
(IF MULTIPLE, _____ ILLUSTRATED)
ADD PRODUCT IMAGE
FOR INDOOR USE ONLY
CSA 22.2 NO. 46 / UL 1278
NUMBER LABEL HERE
W415-2212 / G / 02.10.20
ENGLISH
FRENCH PG. 35
2021

Advertisement

Table of Contents
loading

Summary of Contents for Napoleon Alluravision Series

  • Page 1 INTERTEK LOGO BARCODE LABEL ON THE OWNER’S MANUAL” Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com $10.00 W415-2212 / G / 02.10.20...
  • Page 2 safety information WARNING • If equipped with a heater, this appliance can be hot when operated and can cause severe burns if contacted. • Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fi re or injury. •...
  • Page 3 safety information WARNING • To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a carpet, where openings may become blocked. • Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
  • Page 4: Table Of Contents

    table of contents dimensions general information listing approvals general instructions rating plate information hardware list label location location unpacking and testing the appliance grounding the appliance installation minimum clearance to combustibles minimum mantel clearances installing the appliance onto the wall recessing the appliance into the wall 4.4.1 trim installation (recessed installation only) 4.4.2 installing the appliance into a mantel...
  • Page 5: Dimensions

    dimensions 1.0 dimensions front view side view 17 5/16” 15 7/8” 11 1/16” (440mm) (402mm) (281mm) VIEWING AREA CORD LOCATION 3/4” (18mm) CORD LOCATION top view Dimensions Model No. NEFL42CHS-1 44 7/16” 42 1/16” 40 1/4” (1128mm) (1068mm) (1022mm) NEFL50CHS-1 52 11/16”...
  • Page 6: General Information

    general information 2.0 general information listing approvals Model No. Net Weight Gross Weight NEFL42CHD 63.3 lbs (28.7kg) 82.7 lbs (37.5kg) NEFL50CHD 71.7 lbs (32.5kg) 94.8 lbs (43kg) NEFL60CHD 82.7 lbs (37.5kg) 109.1 lbs (49.5kg) Description Electric Appliance 99.6 lbs (45.2kg) 130 lbs (59kg) NEFL74CHD 3 Way Mounting Unit...
  • Page 7: Rating Plate Information

    DÉSIGNÉ EN AMÉRIQUE DE NORD PAR WOLF STEEL LTD. BY WOLF STEEL LTD. MADE IN CHINA FABRIQUÉ EN CHINE WOLF STEEL LTD. 24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA NEFL SERIAL NUMBER/NO. DE SÉRIE: W385-2226 note: The rating plate must remain with the appliance at all times. It must not be removed.
  • Page 8: Label Location

    general information label location Hot Surface Label (W385-2017) Front Glass Label Do Not Cover Label (W385-2321) (W385-2210) Warning Label (W385-1943) Power Cord Rating Plate Label Hardwiring Warning Label (W385-2380) (NEFL42-100CHD only) Hardwiring Label (W385-2224 or W385-2225) Wiring Diagram Label (W385-2222 or W385-2223) Caution Label (W385-1945) Warning Label...
  • Page 9: Location

    locating appliance 3.0 location WARNING • Due to high temperatures, this electric appliance should be located out of traffi c. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36” (91.4cm) from the front of the appliance.
  • Page 10: Installation

    4.0 installation installation WARNING • Risk of fi re! The power cord must not be pinched against a sharp edge. Secure cord to avoid tripping or snagging to reduce the risk of fi re, electric shock, or personal injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar items.
  • Page 11: Installing The Appliance Onto The Wall

    installation installing the appliance onto the wall Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. 1. Select a location that is not prone to moisture and is located at least 36” (91.4cm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc.
  • Page 12 installation 7. Install 2 screws through the side wall mounting brackets to secure the appliance to the wall (Fig. 4-2). Wood Screw Metal Screws Fig. 4-2 Side Wall Mounting Bracket 8. Install side panels (see “side panel installation” section). 9. Place the crystals or optional topaz glass chips and drift wood logs (CHD models only) along the media tray (see “crystal ember installation”...
  • Page 13: Recessing The Appliance Into The Wall

    installation 4.3.1 side panel installation (wall mount installation only) 1. Install left and right panels (Fig. 4-3) by securing 4 fasteners (2 per panel) to bottom of appliance (Fig. 4-4). Fig. 4-3 Fig. 4-4 recessing the appliance into the wall Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall.
  • Page 14: Trim Installation (Recessed Installation Only)

    installation 5. Install trims (see “trim installation” section). 6. Hold the appliance up to ensure it will fi t into the framing (see “framing - recessed installation” section). 7. Apply shims (not supplied) between the appliance and the frame. 8. Use 4 screws to secure the appliance into the wall (Fig. 4-9). Do not overtighten screws. Fig.
  • Page 15: Installing The Appliance Into A Mantel

    installation 4.4.2 installing the appliance into a mantel 1. Remove the front glass (see “front glass installation and removal” section). 2. Install the top and bottom brackets (not supplied). 3. Insert the appliance into the mantel and secure it with the brackets. For appropriate mantel installation instructions, consult your authorized dealer.
  • Page 16: 120V Hard Wiring Installation

    installation 120V hard wiring installation 4.5.1 NEFL42 / 50 / 60 / 74 CHS 120V hardwiring WARNING • Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and repair this electric appliance. If it is necessary to hard wire this appliance, a qualifi...
  • Page 17: Nefl42 / 50 / 60 / 74 Chd 120V Hardwiring

    installation 4.5.2 NEFL42 / 50 / 60 / 74 CHD 120V hardwiring note: There are 5 wires from the appliance junction that connect to 120V power supply (breaker panel): 1 white (neu- tral), 2 yellow (heater & neutral), 1 black (power L1), and 1 green (ground). Do NOT connect red wire to power supply (breaker panel).
  • Page 18: 240V Hard Wiring Installation (Nefl42 / 50 / 60 / 74 / 100 Chd Only)

    installation 240V hard wiring installation (NEFL42 / 50 / 60 / 74 / 100 CHD only) WARNING • Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and repair this electric appliance. If it is necessary to hard wire this appliance.
  • Page 19 installation 1. Remove the securing screws from the electrical cover plate located on the rear left side of the appliance. 2. Loosen the securing screws from the terminal block to remove the cord from the terminal block. 3. REMOVE 2 JUMPER WIRES IN THE TERMINAL BLOCK. 4.
  • Page 20: Framing - Recessed Installation

    framing 5.0 framing - recessed installation Measurements from body of appliance: Sides, Back, Top 0” FINISHING MATERIAL JUNCTION BOX (NON-LOAD BEARING) 4 1/2" 6 1/16" 4 1/2” 152mm 89mm 6 1/16” [89mm] [152mm] minimum for CHS minimum for CHD models models Model No.
  • Page 21: Finishing

    6.0 fi nishing fi nishing WARNING • Power supply service must be completed prior to fi nishing to avoid reconstruction. • Heat vents and air openings cannot be covered in any circumstances. note: Ensure to remove the 2 screws from the plastic ember bed panel before applying crystals embers and/or logs. crystal ember installation The glass front must be removed and the appliance must be secured in its fi...
  • Page 22: Front Glass Installation And Removal

    fi nishing Recommended drift wood log placement for NEFL60CHD Recommended drift wood log placement for NEFL74CHD Recommended drift wood log placement for NEFL100CHD front glass installation and removal WARNING • Before the front glass is installed or removed, unplug the appliance and wait until appliance is cool to touch.
  • Page 23: Wiring Diagram

    wiring diagram 7.0 wiring diagram WARNING • Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and repair this electric appliance. NEFL42 / 50 / 60 / 74 CHS wiring diagram For 74”...
  • Page 24: Nefl42 / 50 / 60 / 74 / 100 Chd Wiring Diagram

    wiring diagram NEFL42 / 50 / 60 / 74 / 100 CHD wiring diagram For 74” and 100” Models For 74” and 100” Models note: 240V hard wiring illustrated. See “120V hard wiring installation” section for 120V hard wiring. W415-2212 / G / 02.10.20...
  • Page 25: Operation

    8.0 operation operation Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate. attention: Ensure the house circuit breakers for the power supply are turned on. In the event of a power failure, the appliance will lose its memory function and will reset to factory mode when the power returns.
  • Page 26: Operating Remote Control

    operation operating remote control NEFL42 / 50 / 60 / 74 / 100CHD remote NEFL42 / 50 / 60 / 74CHS remote Turns the appliance on/off. Controls ember bed light Power settings. Controls fl ame brightness. Blue Flame Settings: L0 - Ember bed light off Settings: L1 - White F0 - Flame off...
  • Page 27: Maintenance

    9.0 maintenance operation WARNING • In preparation for maintenance, always disconnect the power. • Allow the appliance to cool before performing any cleaning, maintenance, or relocation of the appliance. • Turn controls to off and remove plug from outlet. Alternatively, turn off the house circuit breaker to appliance receptacle.
  • Page 28: Replacement Parts

    10.0 replacement parts replacements WARNING • Failure to position the parts in accordance with this manual or failure to use only parts specifi cally approved with this appliance may result in property damage or personal injury. Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can be ordered through your Authorized dealer / distributor.
  • Page 29: Nefl42 / 50 / 60 / 74 Chs

    replacement parts 10.1 NEFL42 / 50 / 60 / 74 CHS note: Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to vacuum away any broken glass from inside the appliance before operation. 20 21 Items may not appear exactly as illustrated.
  • Page 30: Nefl42 / 50 / 60 / 74 / 100 Chd

    replacement parts 10.2 NEFL42 / 50 / 60 / 74 / 100 CHD 22 23 20 21 Items may not appear exactly as illustrated. Part Number REF. Description Stocked NEFL42CHD NEFL50CHD NEFL60CHD NEFL74CHD NEFL100CHD Front Glass W010-4188-SER W010-4189-SER W010-4190-SER W010-4191-SER W010-4192-SER Flame Projection Plastic Panel W565-0284-SER...
  • Page 31: Troubleshooting

    11.0 troubleshooting troubleshooting WARNING • Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and repair this electric appliance. symptom problem solution Appliance will not Appliance is not plugged into an Check plug, and plug in the appliance if necessary.
  • Page 32 troubleshooting symptom problem solution Ember bed is Brightness not selected. See “operation” section. not glowing or Ember LED issue. Inspect the ember bed LEDs and replace, if necessary. dimming. Main PCB board issue. Inspect the main PCB board and replace, if necessary. LED fl...
  • Page 33: Warranty

    Notwithstanding any provisions contained in the Premium Warranty, Napoleon responsibility under this warranty is defi ned as above, and it shall not in any event extend to any incidental, consequential, or indirect damages.
  • Page 34 NAPOLEON CELEBRATING OVER 40 YEARS OF HOME COMFORT PRODUCTS 7200, Route Transcanadienne, Montréal, Québec H4T 1A3 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030 Phone: 1-866-820-8686...
  • Page 35 IF SEPARATE MANUALS, ADD “PLACE LOGO BARCODE LABEL ON THE OWNER’S MANUAL” Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Téléphone 1 (866) 826 8686 • www.napoleon.com • hearth@napoleon.com $10.00...
  • Page 36 consignes de sécurité AVERTISSEMENT • Si équipé avec un chauffage, cet appareil peut être chaud lorsqu’il fonctionne et peut causer de graves brûlures en cas de contact. • Ne faites pas fonctionner l’appareil avant d’avoir lu et compris les instructions d’utilisation. L’incapacité de respecter les instructions pourrait causer un incendie ou des blessures corporelles.
  • Page 37 consignes de sécurité AVERTISSEMENT • Pour prévenir les risques d’incendie, ne bloquez pas les entrées d’air et les sorties d’air de quelque manière que ce soit. Ne placez pas cet appareil sur une surface molle telle qu’un tapis où les ouvertures pourraient se bloquer.
  • Page 38 table des matiéres dimensions information générale liste d’homologations instructions générales information à propos de la plaque d’homologation liste des pièces emplacement de l’étiquette emplacement déballage et test de l’appareil mise à la terre de l’appareil installation dégagements minimale aux combustibles dégagements minimaux du manteau installation de l’appareil sur le mur encastrer l’appareil dans le mur...
  • Page 39: Dimensions

    informations générales 1.0 dimensions vue de face vue de côté 17 5/16” 15 7/8” 11 1/16” (440mm) (402mm) DIMENSIONS DE (281mm) VIEWING AREA VISION EMPLACEMENT CORD LOCATION DE CORDON 3/4” (18mm) EMPLACEMENT CORD LOCATION DE CORDON vue de dessus Dimensions N°...
  • Page 40: Information Générale

    informations générales 2.0 information générale liste d’homologations Numéro de Poids Net Poids Brut modèle NEFL42CHD 63,3 lbs (28,7kg) 82,7 lbs (37,5kg) NEFL50CHD 71,7 lbs (32,5kg) 94,8 lbs (43kg) NEFL60CHD 82,7 lbs (37,5kg) 109,1 lbs (49,5kg) Numéro de Appareils Électrique modèle NEFL74CHD 99,6 lbs (45,2kg) 130 lbs (59kg)
  • Page 41: Information À Propos De La Plaque D'homologation

    DÉSIGNÉ EN AMÉRIQUE DE NORD PAR WOLF STEEL LTD. BY WOLF STEEL LTD. MADE IN CHINA FABRIQUÉ EN CHINE WOLF STEEL LTD. 24 NAPOLEON ROAD, NEFL BARRIE, ON, L4M 0G8 CANADA SERIAL NUMBER/NO. DE SÉRIE: W385-2226 note: La plaque d’homologation doit resté avec l’appareil à tous les temps. Il ne doit pas être enlevé.
  • Page 42: Emplacement De L'étiquette

    information générale emplacement de l’étiquette L’étiquette de surface chaude L’étiquette L’étiquette « Ne pas couvrir » (W385-2017) de la vitre avant (W385-2210) (W385-2321) L’étiquette d’avertissement (W385-1943) Cordon d’alimentation L’étiquette de plaque d’homologation L’étiquette d’avertissement de câblage (W385-2380) (NEFL42-100CHD seulement) L’étiquette de câblage (W385-2224 ou W385-2225) L’étiquette de diagramme de câblage...
  • Page 43: Emplacement

    3.0 appareil de localisation 3.0 emplacement AVERTISSEMENT • En raison des températures élevées, cet appareil électrique doit être situé hors de circulation. Conservez des matériaux combustibles tels que des meubles, des coussins, des litières, des papiers, des vêtements et des rideaux à...
  • Page 44: Installation

    installation 4.0 installation AVERTISSEMENT • Risque d’incendie! Le cordon d’alimentation ne doit pas être coincé contre une arrète vive. Fixez le cordon pour éviter les chutes ou les accrochages afi n de réduire le risque d’incendie, de choc électrique ou de blessures corporelles.
  • Page 45: Installation De L'appareil Sur Le Mur

    installation installation de l’appareil sur le mur En raison des nombreux matériaux utilisés sur différents murs, il est fortement recommandé de consulter votre constructeur local avant d’installer cet appareil sur le mur. 1. Choisissez un endroit n’est pas propice à l’humidité et se trouve à au moins 36“ (91,4 cm) des matériaux combustibles tels que rideaux, meubles, literie, papier, etc.
  • Page 46 installation 7. Installez les 3 vis à travers les supports de montage muraux pour fi xer l’appareil au mur (Fig. 4-2). Vis à Bois Vis Métalliques Fig. 4-2 Support de Montage Mural 8. Installez le couvercle latéral (voir la section « installation du panneau latéral »). 9.
  • Page 47: Encastrer L'appareil Dans Le Mur

    installation 4.3.1 installation de panneau latéral (installation murale uniquement) 1. Installez les panneux droit et gauche (Fig. 4-3) en fi xant les 4 attaches (2 par panneau) au bas de l’appareil (Fig. 4-4). Fig. 4-4 Fig. 4-3 encastrer l’appareil dans le mur En raison des nombreux matériaux utilisés sur différents murs, il est fortement recommandé...
  • Page 48: Installation De Garniture (Installation Encastrée Uniquement)

    installation 5. Installez les garnitures (voir la section « installation de garniture »). 6. Tenez l’appareil en place pour vous assurer qu’il s’insère dans le cadre (voir la section « encadrement - installation encastrée »). 7. Appliquez les cales (non fourni) entre l’appareil et le cadre. 8.
  • Page 49: Installation De L'appareil Dans Un Manteau

    installation 4.4.2 installation de l’appareil dans un manteau 1. Retirez le verre avant (voir la section « installation et enlèvement du verre avant »). 2. Installez les supports supérieur et inférieur (non fourni). 3. Insérez l’appareil dans le manteau et fi xez-le avec les supports. Pour obtenir les instructions d’installation appropriées, consultez votre revendeur agréé.
  • Page 50: Installation De Câblage Dur 120V

    installation installation de câblage dur 120V 4.5.1 câblage 120V de NEFL42 / 50 / 60 / 74 CHS AVERTISSEMENT • Coupez l’alimentation électrique à l’appareil et laissez-le refroidir avant d’effectuer un entretien. Seulement un technicien de service qualifi é peut effectuer l’entretien ou la réparation de cet appareil électrique. S’il est nécessaire de câbler cet appareil, un électricien qualifi...
  • Page 51: Câblage 120V De Nefl42 / 50 / 60 / 74 Chd

    installation 4.5.2 câblage 120V de NEFL42 / 50 / 60 / 74 CHD note: Il y a 5 fi ls de la jonction de l’appareil qui se connectent à une alimentation 120V (panneau de rupture): 1 blanc (neutre), 2 jaune (chauffage neutre), 1 noir (puissance L1) et 1 vert (masse). NE PAS connectez le fi l rouge à l’alimentation (panneau de disjoncteur).
  • Page 52: Installation De Câblage Dur 240V (Nefl42 / 50 / 60 / 74 / 100 Chd Seulement)

    installation installation de câblage dur 240V (NEFL42 / 50 / 60 / 74 / 100 CHD seulement) AVERTISSEMENT • Coupez l’alimentation électrique à l’appareil et laissez-le refroidir avant d’effectuer un entretien. Seulement un technicien de service qualifi é peut effectuer l’entretien ou la réparation de cet appareil électrique. S’il est nécessaire de câbler cet appareil, un électricien qualifi...
  • Page 53 installation 1. Retirez les vis de fi xation de la plaque de recouvrement électrique située à l’arrière gauche de l’appareil. 2. Desserrez les vis de fi xation du bornier pour retirer le cordon du bornier. 3. RETIREZ LES DEUX FILS DE DÉRIVATION DANS LE BLOC TERMINAL. 4.
  • Page 54: Encadrement - Installation Encastrée

    framing 5.0 encadrement - installation encastrée Les mesures sont prises du corps: Côtés, Arrière, Dessus 0” MATÉRIAU DE FINITION BOÎTE DE JUNCTION BOX DÉRIVATION (PALIER NON 4 1/2" 6 1/16" CHARGE) 4 1/2” 152mm 89mm 6 1/16” [89mm] [152mm] minimum pour les minimum pour les modèles CHS modèles CHD...
  • Page 55: Installation De Braise En Cristal

    6.0 fi nition fi nition AVERTISSEMENT • Le service d’alimentation doit être complété avant de fi nir d’éviter la reconstruction. • Les évents de chaleur et les ouvertures d’air ne peuvent être couverts en aucune circonstance. note: Assurez-vous d’enlever les 2 vis du panneau plastique du lit de braise avant d’appliquer les braises en cristaux et/ou les bûches.
  • Page 56: Installation Et Enlèvement De La Vitre Avant

    fi nition Emplacement de bûches de bois fl otté recommandé pour NEFL60CHD Emplacement de bûches de bois fl otté recommandé pour NEFL74CHD Emplacement de bûches de bois fl otté recommandé pour NEFL100CHD 6.3 installation et enlèvement de la vitre avant AVERTISSEMENT •...
  • Page 57: Schéma De Câblage

    Schéma de câblage 7.0 schéma de câblage AVERTISSEMENT • Éteignez complètement l’appareil et laissez refroidir avant de procéder à l’entretien. Seul un technicien qualifi é doit entretenir et réparer cet appareil électrique. 7.1 schéma de câblage NEFL42 / 50 / 60 / 74 CHS Pour Modèles 74”...
  • Page 58: Schéma De Câblage Nefl42 / 50 / 60 / 74 / 100 Chd

    schéma de câblage 7.2 schéma de câblage NEFL42 / 50 / 60 / 74 / 100 CHD *LED Haut Pour Modèles 74” et 100” *LED de Braise Pour Modèles 74” et 100” *Flamme LED Ventilateur1 LO Ventilateur1 HI Ventilateur2 LO Ventilateur2 HI note: 240V câblage est illustré...
  • Page 59: Fonctionnement

    8.0 fonctionnement operation Une fois que l’appareil a été branché sur une prise électrique mise à la terre, il est prêt à fonctionner. attention: Assurez-vous que les disjoncteurs de la maison de l’alimentation sont allumés. En cas de panne de courant, l’appareil perd sa fonction mémoire et se réinitialise en mode d’usine lorsque l’alimentation revient.
  • Page 60: Fonctionnement De La Télécommande

    fonctionnement 8.2 fonctionnement de la télécommande Télécommande pour les modèles Télécommande pour les modèles NEFL42/50/60/74/100CHD NEFL42/50/60/74CHS Contrôle les réglages de la lu- Activé ou désactivé l’appareil. Puissance mière du lit de braise. Contrôle la luminosité de la Flamme bleue Paramètres: fl...
  • Page 61: Entretien

    9.0 entretien operation AVERTISSEMENT • En preparation pour l’entretien, débranchez toujours l’alimentation. • Laissez l’appareil électrique refroidir avant d’effectuer tout nettoyage, entretien ou relogement de l’appareil. • Éteignez les commandes et retirez la fi che de la prise ou éteignez le disjoncteur de la maison sur la prise de l’appareil.
  • Page 62: Pièces De Rechange

    10.0 pièces de rechange replacements AVERTISSEMENT • Omettre de positionner les pièces conformément à ce manuel ou d’utiliser uniquement des pièces spécifi quement approuvées pour cet appareil peut causer des dommages matériels ou des blessures corporelles. Contactez votre détaillant pour les questions concernant les prix et la disponibilité des pièces de remplace- ment.
  • Page 63: Nefl42 / 50 / 60 / 74 Chs

    pièces de rechange 10.1 NEFL42 / 50 / 60 / 74 CHS note: Des précautions doivent être prises lors de l’élimination et de l’élimination de tout verre brisé ou de composants endommagés. Assurez-vous d’aspirer tout verre brisé de l’intérieur de l’appareil avant l’opération. 20 21 Ces articles peuvent différer de ceux illustrés.
  • Page 64: Nefl42 / 50 / 60 / 74 / 100 Chd

    pièces de rechange 10.2 NEFL42 / 50 / 60 / 74 / 100 CHD 20 21 22 23 Ces articles peuvent différer de ceux illustrés. Numéro de Piéces RÉF. Description Stock NEFL42CHD NEFL50CHD NEFL60CHD NEFL74CHD NEFL100CHD Verre avant W010-4188-SER W010-4189-SER W010-4190-SER W010-4191-SER W010-4192-SER...
  • Page 65: Guide De Dépannage

    11.0 guide de dépannage troubleshooting AVERTISSEMENT • Coupez l’alimentation électrique à l’appareil et laissez-le refroidir avant d’effectuer un entretien. Seulement un technicien de service qualifi é peut effectuer l’entretien ou la réparation de cet appareil électrique. symptôme problème solution L’appareil L’appareil n’est pas branché...
  • Page 66 guide de dépannage symptôme problème solution La luminosité du Éclat de fl amme n’est pas Voir la section « fonctionnement ». jeu de fl ammes sélectionné. est faible ou Problème avec les fl amme DELs. Vérifi ez les DELs et remplacez-les si nécessaire. inexistante.
  • Page 67: Garantie

    warranty 12.0 garantie Les appareils électriques Napoléon sont fabriqués conformément aux normes strictes du Système de Gestion de la Qualité mondialement reconnu ISO 9001 : 2015. Les produits Napoléon sont conçus avec des composants et des matériaux de qualité supérieure, assemblés par des artisans qualifi...
  • Page 68 À À À T IO ODUITS CONFORT 7200, Route Transcanadienne, Montréal, Québec H4T 1A3 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030 Téléphone: 1-866-820-8686 napoleon.com...

Table of Contents