1. Manuals
  2. Brands
  3. Zero 88 Manuals
  4. Lighting Equipment
  5. Betapack 4
  6. User manual

Zero 88 Betapack 4 User Manual

Hide thumbs Also See for Betapack 4:
Table of Contents

Advertisement

Quick Links

This product must be earthed
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
This equipment is designed for professional stage
lighting control and is unsuitable for any other purpose. It
should be used by, or under the supervision of, an
appropriately qualified or trained person.
USER MANUAL
Betapack 4
Betapack 4 User Manual v1
E&OE. Cooper Lighting Solutions reserves the right to
make changes to the equipment and specification
described in this manual without prior notice.
© Cooper Lighting Solutions UK Ltd
9850-000753-00
Page 1 of 12

Advertisement

Table of Contents
loading

Related Manuals for Zero 88 Betapack 4

Summary of Contents for Zero 88 Betapack 4

  • Page 1 © Cooper Lighting Solutions UK Ltd Betapack 4 User Manual v1 9850-000753-00 Page 1 of 12...

  • Page 2: Table Of Contents

    Super user ...............9 Three phase delta ............4 Lock/Unlock ..............9 Mounting / Installation ........5 Resetting Betapack 4 ..........9 In a 19" Rack ..............5 Firmware Version ............9 On a wall ................. 5 Internal Temperature ..........9 For Portable Use ............

  • Page 3: Introduction

    To remove the cover WARNING! Do not remove the covers without first completely disconnecting Betapack 4 from the mains supply Isolate and disconnect Betapack 4 from the mains supply. The Triacs (type BTA40-600A/B) are located under the bottom cover. To remove the bottom cover, remove the The mains supply terminals (and output terminals on the four screws “B”...

  • Page 4: Connecting The Mains

    Diagram 2:  Phase to Neutral voltage must not exceed 255VAC.  All wiring entering Betapack 4 must be rated to +85ºC, H07RN-F cable is recommended.  Cut outs are provided on the ends and rear for PG21 glands;...

  • Page 5: Mounting / Installation

    On a wall Undo the four screws ‘X’ to remove the brackets, replace the screws in the holes for future use. Stand Betapack 4 Diagram 5 on one end. Remove the two screws ‘Y’ (see Diagram 5), fit the brackets as shown and replace screws ‘Y’. Fit the other bracket on the other end.

  • Page 6: Configuration & Settings

    Betapack 4. Around the outside of these displays are eight red LEDs which indicate the current Channel test set-up mode of Betapack 4. An additional green LED is While keeping the ‘Enter’ button held down in Default used for DMX indication.

  • Page 7: Dmx Address

    DMX Address If memories are cleared which are used in sequences, There are 2 ways that Betapack 4 can be patched – a they will be removed automatically from those sequences. single DMX start address can be set for the block of 6...

  • Page 8: Preheat

    ‘Switch’. Topset Topset can be selected on a per channel or all channel basis. On Betapack 4, Topset is applied as a limiting (not scaling) value. Select ‘Topset’ by cycling through the modes using the ‘Mode’...

  • Page 9: Super User

    The ‘Enter’ button toggles this setting between “ron” (RDM enable) and” rof” (RDM disabled). If Super User is entered when Betapack 4 is locked, only the unlock function will be available. The display will show “UNL”. To unlock Betapack 4, press and hold the ‘Enter’...

  • Page 10: Electrical

    One male and one female 5 pin XLR connector. DMX line is automatically terminated when the loop-through plug is not inserted. The pin assignment is: Betapack 4 is designed to operate on 230VAC +10% - 15% at 50-60Hz (auto sensing). The pack may not Pin 1 operate satisfactorily outside this specification.

  • Page 11: Mechanical

    Assessment of products with respect to RoHS II a safe level. The table below shows how Betapack 4 will react under these conditions. (Note: The temperature shown on the display will be the actual temperature not the rounded figures given below).

  • Page 12: Troubleshooting

    “Topset” for further details. 3. If Betapack 4 is wired single phase check that the single-phase link bar has been fitted. If it is fitted check the screws are adequately tightened. Please see “diagram 3” for further details.

Table of Contents