Page 2: Table Of Contents
Contents Introduction..........8 Package Contents.
Page 3 Custom White Balance......... . 129 White Balance Correction.
Page 4 Canon Log Settings........
Page 5 Voice Memo Recording and Playback......430 Movie Playback..........435 Editing a Movie's First and Last Scenes.
Page 6 Checking and Editing Network Settings......669 Syncing Time Between Cameras........691 GPS Features.
Page 7 Custom Shooting Mode (C1-C3)........808 Resetting Camera..........811 Copyright Information.
Page 8: Introduction
Canon website and update the firmware. Connecting other devices Use the included interface cable or a Canon cable when connecting the camera to a computer or other device. When connecting an interface cable, also use the included cable protector ( •...
Page 9: Package Contents
Package Contents Before use, make sure the following items are included in the package. If anything is missing, contact your dealer. Camera (with body cap and battery compartment cap) Eyecup Eg Battery Pack LP-E19 (with protective cover) Battery Charger LC-E19 (with protective cover) Strap Interface Cable...
Page 10 Attach Eyecup Eg to the viewfinder eyepiece. Be careful not to lose any of these items. No software CD-ROM is included. Software ( ) can be downloaded from the Canon website. Caution The transmission rate when the included interface cable is used is equivalent to...
Page 11: Instruction Manuals
Advanced User Guide Complete instructions are provided in this Advanced User Guide. For the latest Advanced User Guide, refer to the following website. https://cam.start.canon/C001/ Lens/Software Instruction Manual Download from the following website. https://cam.start.canon/ Note Select [ : Manual/software URL] to display the QR code on the camera screen.
Page 12: Quick Start Guide
Quick Start Guide Insert the battery ( Upon purchase, charge the battery to start using ( Insert the card ( You can insert two cards. Attach the lens ( Align the red mount index on the lens with the red mount index on the camera to attach the lens.
Page 13 Set the lens's focus mode switch to < > ( Set the power switch to < > ( Set the shooting mode to < > ( Press the < > button. Look at the top LCD panel and turn the < >...
Page 14 Focus on the subject ( Look through the viewfinder and center the subject on the screen. Press the shutter button halfway, and the camera will focus on the subject. Take the picture ( Press the shutter button completely to take the picture. Review the picture.
Page 15: About This Guide
About This Guide Icons in This Guide Basic Assumptions for Operational Instructions and Sample Photos Icons in This Guide Indicates the Main dial. < > Indicates the Quick control dial. < > Indicates the Multi-controller. < > Indicates the Smart controller. <...
Page 16 Basic Assumptions for Operational Instructions and Sample Photos Before following any instructions, make sure the power switch is set to < > ( It is assumed that all the menu settings and Custom Functions are set to their defaults. Screen shots in this guide show the default menu settings for NTSC regions (North America, Japan, South Korea, Mexico, etc.) as an example.
Page 17: Compatible Cards
Compatible Cards The following cards can be used with the camera regardless of capacity. If the card is new or was previously formatted (initialized) by another camera or computer, format the card with this camera ( CFexpress cards * Type B compatible Cards That Can Record Movies When recording movies, use a card with ample performance (fast enough writing and reading speeds) for the movie recording quality (...
Page 18: Safety Instructions
Safety Instructions Be sure to read these instructions in order to operate the product safely. Follow these instructions to prevent injury or harm to the operator of the product or others. WARNING: Denotes the risk of serious injury or death. Keep the product out of the reach of young children.
Page 19 Observe the following instructions when using a battery charger. • Periodically remove any dust buildup from the power plug and power outlet using a dry cloth. • Do not plug in or unplug the product with wet hands. • Do not use the product if the power plug is not fully inserted into the power outlet. •...
Page 20 CAUTION: Denotes the risk of injury. Do not fire the flash near the eyes. It may hurt the eyes. Do not look at the screen or through the viewfinder for prolonged periods of time. This may induce symptoms similar to motion sickness. In such a case, stop using the product immediately and rest for a while before resuming use.
Page 21: Handling Precautions
If you accidentally drop the camera into water or are concerned that moisture (water), dirt, dust, or salt may have gotten inside it, promptly consult the nearest Canon Service Center. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Page 22 If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your nearest Canon Service Center or check the camera yourself and make sure it is working properly.
Page 23 Besides dust entering the camera from outside, in rare cases, lubricant from the camera's internal parts may adhere to the front of the sensor. If smudges are visible on images, have the sensor cleaned by a nearest Canon Service Center.
Page 24: Part Names
Part Names Attaching the Strap Using the Cable Protector (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (10) (11) (23)
Page 25 Lens mount index Depth-of-field preview button Multi-function button 2 Self-timer lamp Shutter button Grip Vertical-grip On/Off switch < > Vertical-grip AF area selection/ Vertical-grip AF method selection/ Vertical-grip multi-function/ Vertical-grip FE lock/ Vertical-grip multi-spot metering button Vertical-grip main dial (10) Vertical-grip shutter button (11) Hand strap mount...
Page 26 (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (10) (21)
Page 27 < > White balance selection button < > LCD panel illumination button GPS antenna Hot shoe Flash sync contacts Eyecup Screen < > Quick Control button < > Vertical-grip AF start button/ Vertical-grip smart controller (10) Speaker (11) < > Exposure compensation/ Aperture value setting button (12) <...
Page 28 (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (10) (22)
Page 29 < > Flash exposure compensation/ Metering mode selection button < > Shooting mode selection button < > Drive mode/ AF operation selection button < > AEB setting button System extension mounting hole Terminal cover System extension terminal < > External microphone IN/ Line input terminal <...
Page 30 (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (10) (22) (11) (23)
Page 31 < > Focal plane mark < > Info button < > Menu button Strap mount < > Network lamp Battery release handle Battery < > Playback button < > Card/Image size selection button (10) < > Index/Magnify/Reduce button (11) Rear LCD panel (12) Card slot 1 (13)
Page 32 Viewfinder information display (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (10) (21) (22) (24) (25) (26) (23) (27) (28) (29)
Page 33 Electronic level Spot metering circle Focusing screen Grid Metering mode Shooting mode White balance Drive mode Image type (10) AF operation (11) Large Zone AF frame (12) Area AF frame (13) < > AF point < > Spot AF point (14) Flicker detection (15)
Page 34 (10) (11) (12) (13) (14)
Page 35 < > ISO speed Manual exposure < > AE lock AEB in progress Multi-spot metering < > Flash ready FE lock out-of-range warning < > FE lock FEB in progress < > High-speed sync AF point selection AF point registration Current time Card warning ( 1/2/1,2)
Page 36 Top LCD panel (10)
Page 37 Shutter speed Bulb ( Bulb exposure time (min.:sec.) FE lock ( Busy ( Multi-function lock warning ( ) Cleaning image sensor ( AI Bounce mode active ( No-card warning ( Error codes ( Shooting mode Program AE Aperture-priority AE Manual exposure Shutter-priority AE Custom shooting mode <...
Page 38 (10) (11) (12)
Page 39 < > ISO speed < > Highlight tone priority White balance Auto (Ambience priority) Auto (White priority) Daylight Shade Cloudy Tungsten light White fluorescent light Flash Custom Color temperature/Personal white balance < > Monochrome shooting < > Flash exposure compensation Exposure level indicator (setting value) Exposure compensation amount AEB range...
Page 40 Rear LCD panel (10) (11) (12) (13) (14) (15) < > GPS acquisition status* < > Card 2 indicator < > Card 2 selection icon < > Card 1 indicator < > Card 1 selection icon Image size Large Medium1 Medium2 Small HEIF...
Page 41 Battery Pack LP-E19 Battery lock lever Contacts Protective cover Battery release handle...
Page 42 Battery Charger LC-E19 Charger for Battery Pack LP-E19 ( Contacts Battery slots Power cord socket Recharge performance check button/Calibration button Charge lamp/Recharge performance check lamp/Discharge time lamp Calibration (discharge) lamp Protective cover (two included) Power cord...
Page 43 Attaching the Strap Pass the end of the strap through the strap mount from the bottom, then pass it through the strap buckle as shown. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle.
Page 44 Using the Cable Protector When connecting the camera to a computer, use the included interface cable or a Canon cable. When connecting an interface cable, also use the included cable protector. Using the cable protector helps prevent accidental disconnection and terminal damage.
Page 45 (3) Included interface cable...
Page 46 (4) HDMI cable (sold separately) Using an optional Canon interface cable When using an optional Canon interface cable, pass the cable through the clamp (5) as shown before attaching the clamp to the cable protector. Caution Using the camera when the interface cable is connected without the cable protector may damage the digital terminal.
Page 47: Software
Software Software Overview Downloading and Installing EOS Software or Other Dedicated Software Downloading the Software Instruction Manual Software Overview This section summarizes software used with EOS cameras. Note that downloading and installing the software requires an internet connection. The software cannot be downloaded or installed in environments without an internet connection.
Page 48 Downloading and Installing EOS Software or Other Dedicated Software Always install the latest version of the software. Update any previous versions that are installed by overwriting them with the latest version. Caution Do not connect the camera to a computer before you install the software. The software will not be installed correctly.
Page 49 Download the software. Connect to the internet from a computer and access the following Canon website. https://cam.start.canon/ Select your country or region of residence and download the software. Depending on the software, you may need to enter the camera's serial number.
Page 50 Downloading the Software Instruction Manual Software Instruction Manuals (PDF files) can be downloaded from the Canon website to your computer, etc. Software Instruction Manual download site https://cam.start.canon/...
Page 51: Preparation And Basic Operations
Preparation and Basic Operations This chapter describes preparatory steps before you start shooting and the basic camera operations. • Charging the Battery • Inserting/Removing Batteries • Inserting/Removing Cards • Turning on the Power • Attaching/Detaching Lenses • Basic Operations • Menu Operations and Settings •...
Page 52: Charging The Battery
Charging the Battery Connect and plug in the battery charger. Connect the power cord to the charger and plug the other end into a power outlet. All indicator lamps are off when no batteries are loaded. Remove the protective cover. Remove the included protective covers from the charger and battery.
Page 53 Charge the battery. Slide the battery in (in the opposite direction from protective cover removal) and make sure it is securely attached to the charger. You can load a battery into either slot or slot Charging begins, and the charge lamp blinks or lights up in green. Charging is finished when all three charge lamps (50%/80%/100%) are lit in green.
Page 54 Charge the battery on the day before or on the day it is to be used. Charged batteries gradually lose their charge, even when they are not used. After charging the battery, remove it and disconnect the charger from the power outlet.
Page 55 < > lamp in green), remove the battery and contact your dealer or the nearest Canon Service Center. If the three charge lamps blink during calibration, remove the battery and contact your dealer or the nearest Canon Service Center.
Page 56: Inserting/Removing Batteries
Inserting/Removing Batteries Insertion Removal Insert a fully charged Battery Pack LP-E19 into the camera. Viewfinder brightness increases when a battery is inserted and decreases after removal. Insertion Remove the battery compartment cap. Insert the battery. Insert the battery firmly, all the way in, then turn the battery release handle as shown by the arrow.
Page 57 Caution There may be a slight delay before the camera turns on when a battery is used in the camera for the first time. You cannot use batteries other than the Battery Pack LP-E19. Note Wipe away any dirt on the battery's water-repellent rubber lining (1) with a moistened cotton swab.
Page 58 Removal Turn the battery release handle and remove the battery. Make sure the power switch is set to < > ( Flip out the battery release handle, turn it as shown by the arrow, and remove the battery. To prevent short-circuits, always attach the included protective cover ) to the battery.
Page 59: Inserting/Removing Cards
Inserting/Removing Cards Insertion Removal This camera accepts two cards. Recording is possible as long as there is at least one card in the camera. With two cards inserted, you can select one card to record to, or you can record the same image to both cards at once ( Insertion Open the cover.
Page 60 Insert the card. Card 1 Card 2 The card in the left card slot is [ ], and the card on the right is [ With the card label facing you, insert the open side of the card (2) into the card slot.
Page 61 Set the power switch to < > ( (3) Number of available shots (4) Card selection icon (5) Card 1 (6) Card 2 The top LCD panel shows how many shots are available. The rear LCD panel shows which cards are loaded. Cards labeled with <...
Page 62 Removal Open the cover. Set the power switch to < >. Check that the access lamp (1) is off, then open the cover. If [Saving...] is displayed on the screen, close the cover. Remove the card. Press the card eject button to eject the card. Pull the card straight out, then close the cover.
Page 63 Caution When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. To avoid corrupting image data or damaging cards or the camera, never do any of the following while the access lamp is lit or blinking.
Page 64: Turning On The Power
Turning on the Power Setting the Date, Time, and Time Zone Changing the Interface Language Automatic Sensor Cleaning Battery Level Indicator < > The camera turns on. < > The camera turns on. Multi-function locking is engaged ( < > The camera is turned off and does not function.
Page 65 Changing the Interface Language To change the interface language, see Language.
Page 66 Automatic Sensor Cleaning Whenever the power switch is set to < > or < >, the sensor is cleaned automatically (which may make a faint sound). During the sensor cleaning, the screen will display < >. Even during sensor cleaning, you can stop cleaning and shoot immediately by pressing the shutter button halfway ( If you repeatedly turn the power switch to <...
Page 67 Battery Level Indicator When the power switch is set to < >, the battery level will be indicated. Display Level (%) 100–70 69–50 49–20 19–10 9–1 Note Doing any of the following will exhaust the battery faster: • Pressing the shutter button halfway for a prolonged period. •...
Page 68: Attaching/Detaching Lenses
Attaching/Detaching Lenses Attaching a Lens Detaching a Lens All EF lenses can be used. The camera cannot be used with RF, EF-S, or EF-M lenses. Caution Do not look at the sun directly through any lens. Doing so may cause loss of vision. When attaching or detaching a lens, set the camera's power switch to <...
Page 69 Attaching a Lens Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. Attach the lens. Align the red mount index on the lens with the red mount index on the camera and turn the lens as shown by the arrow until it clicks in place.
Page 70 Set the lens's focus mode switch to < >. < > stands for autofocus. < > stands for manual focus. Autofocus will not operate. Remove the front lens cap.
Page 71 Detaching a Lens While pressing the lens release button, turn the lens as shown by the arrow. Turn the lens until it stops, then detach it. Attach lens caps to the lens you removed.
Page 72: Basic Operations
Basic Operations Adjusting the Viewfinder Holding the Camera Shutter Button < > Main Dial < > Quick Control Dial < > Multi-Controller < >: Multi-Function Button < >: AF Start Button/Smart Controller < >: Multi-Function Lock < > LCD Panel Illumination Vertical Shooting Time Display Button Backlighting...
Page 73 Adjusting the Viewfinder Detach the eyecup. Grasp the eyecup on both sides and slide it up to detach it. Make the adjustment. Turn the knob left or right to make the AF points in the viewfinder look sharp. Attach the eyecup. Note If the camera's dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lenses Eg series (sold separately) is recommended.
Page 74 Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake. (1) Horizontal shooting (2) Vertical shooting 1. With your right hand, hold the camera firmly by the camera grip. 2. With your left hand, support the lens from below. 3.
Page 75 Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture value. The exposure value (shutter speed and aperture value) is displayed in the viewfinder and on the top LCD panel for approx.
Page 76 Note The camera will still pause before taking a picture if you press the shutter button completely without pressing it halfway first, or if you press the shutter button halfway and immediately press it completely. Even during menu display or image playback, you can return to shooting standby by pressing the shutter button halfway.
Page 77 < > Main Dial (1) After pressing a button, turn the < > dial. When you press a button such as < > < > < >, or < >, the respective function remains selectable for approx. 6 sec. ( ).
Page 78 Note The operations in (1) can be performed even when the power switch is set to < > (...
Page 79 < > Quick Control Dial (1) After pressing a button, turn the < > dial. When you press a button such as < > < > < >, or < >, the respective function remains selectable for approx. 6 sec. ( ).
Page 80 Note The operations in (1) can be performed even when the power switch is set to < > (...
Page 81 < > Multi-Controller < > is an eight-direction key with center button. To use it, press lightly with the tip of your thumb. Used for operations such as AF point selection, white balance correction, AF point/ magnifying frame movement in Live View shooting or movie recording, magnifying frame movement during playback, or Quick Control settings.
Page 82 < >: Multi-Function Button The < > button is used for operations such as selection of the AF area selection mode )/AF method ( ), FE lock ( ), or multi-spot metering ( To select the AF area or AF method, press the < >...
Page 83 < >: AF Start Button/Smart Controller On this control, you can press the center or drag with your finger. Pressing the < > button activates autofocusing. This is equivalent to pressing the shutter button halfway. You can move the AF point by dragging on the smart controller after pressing the <...
Page 84 < >: Multi-Function Lock With [ 6: Multi function lock] configured ( ) and the power switch set to < >, you can prevent the settings from being changed by accidentally touching the Main dial, Quick control dial, Multi-controller, smart controller, or touch-screen panel. Note Attempting to use any locked camera controls when the power switch is set to <...
Page 85 < > LCD Panel Illumination You can illuminate the top LCD panel and rear LCD panel by pressing the < > button. Each press of the < > button switches illumination on ( ) and off. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination.
Page 86 Vertical Shooting Buttons, dial, and a Multi-controller for vertical shooting are arranged near the bottom of the camera ( When using the controls for vertical shooting, set the vertical-grip On/Off switch to < >. When you are not using these controls, set to < >...
Page 87 Time Display Press the < > button when you are looking through the viewfinder to display the time...
Page 88 Button Backlighting < >, < >, < >, < >, < >, < >, and < > button backlighting is activated when the LCD panels are illuminated, or during menu or Quick Control screen display or image playback. This makes it easier to see the button layout in low-light locations.
Page 89 < > Button Each press of the < > button changes the information shown. The following sample screens are for still photos. Electronic level Custom Quick Control screen Quick Control screen...
Page 90: Menu Operations And Settings
Menu Operations and Settings Menu Screen Menu Setting Procedure Dimmed Menu Items < > button Screen < > button < > Main dial < > Quick control dial < > button...
Page 91 Menu Screen Main tabs Secondary tabs Menu items : Shooting : Autofocus : Playback : Communication features : Set-up : Custom Functions (10) : My Menu (11) Menu settings...
Page 92 Menu Setting Procedure Display the menu screen. Press the < > button to display the menu screen. Select a tab. Each time you press the < > button, the main tab (group of functions) will switch. Turn the < > dial to select a secondary tab. Select an item.
Page 93 Select an option. Turn the < > dial to select an option. The current setting is indicated in blue. Set an option. Press < > to set it. Exit the setting. Press the < > button to return to shooting standby. Note The description of menu functions hereafter assumes that you have pressed the <...
Page 94 Dimmed Menu Items Example: When Highlight tone priority has been set Dimmed menu items cannot be set. The menu item is dimmed if another function setting is overriding it. You can see the overriding function by selecting the dimmed menu item and pressing <...
Page 95: Quick Control
Quick Control You can directly and intuitively select and set the settings displayed. Basic operations are the same for the Quick Control screen and Custom Quick Control screen ( Press the < > button (...
Page 96 Select a setting item. Select with < >. Example of a screen in viewfinder shooting Example of a screen in Live View shooting...
Page 97 Select an option. Turn the < > or < > dial to adjust the setting. Some items are set by pressing a button after this.
Page 98: Touch-Screen Operation
Touch-Screen Operation Tapping Dragging Tapping Sample screen (Quick Control) Use your finger to tap (touch briefly and then remove your finger from) the screen. For example, when you tap [ ], the Quick Control screen appears. By tapping on [ you can return to the preceding screen.
Page 99 Note If [ : Beep] is set to [Touch ], the beep will not sound for touch operations ( Responsiveness to touch operations can be adjusted in [ : Touch control] ( Touching the screen does not change settings (touch control is disabled) when [ (VF shoot) Safety lock] is selected in [ : Touch control] and you have specified button operations (except for menu-based function setup) for the following functions.
Page 100 Dragging Sample screen (Menu screen) Slide your finger while touching the screen.
Page 101: Shooting Mode
Shooting Mode You can shoot in a variety of ways by setting your preferred shutter speed, aperture value, exposure, and more. Note Set the power switch to < > in advance. • P: Program AE • Tv: Shutter-Priority AE • Av: Aperture-Priority AE •...
Page 102: P: Program Ae
P: Program AE The camera automatically sets the shutter speed and aperture value to suit the subject's brightness. * < > stands for Program. * AE stands for Auto Exposure. Set the shooting mode to < >. Press the < >...
Page 103 Focus on the subject. As you look through the viewfinder, aim the AF point over the subject, then press the shutter button halfway. After the camera focuses, the focus indicator < > in the lower right of the viewfinder lights up (in One-Shot AF mode). The shutter speed and aperture value are set automatically and displayed in the viewfinder and on the top LCD panel.
Page 104 Caution If the “30"” shutter speed and the lowest aperture value blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the highest aperture value blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens.
Page 105 The shutter speed and aperture value are blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EL/EX series Speedlite (sold separately, ) is recommended.
Page 106: Tv: Shutter-Priority Ae
Tv: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture value to obtain the standard exposure matching the brightness of the subject. A faster shutter speed can freeze the action of a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion.
Page 107 Set the desired shutter speed. Watch the top LCD panel as you turn the < > dial. Focus on the subject. Press the shutter button halfway. The aperture value is set automatically. Check the display and shoot. As long as the aperture value is not blinking, the standard exposure will be obtained.
Page 108 Caution If the lowest aperture value blinks, it indicates underexposure. Turn the < > dial to set a slower shutter speed until the aperture value stops blinking or set a higher ISO speed. If the highest aperture value blinks, it indicates overexposure. Turn the <...
Page 109: Av: Aperture-Priority Ae
Av: Aperture-Priority AE Depth-of-Field Preview In this mode, you set the desired aperture value and the camera sets the shutter speed automatically to obtain the standard exposure matching the subject brightness. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
Page 110 Set the desired aperture value. Watch the top LCD panel as you turn the < > dial. Focus on the subject. Press the shutter button halfway. The shutter speed is set automatically. Check the display and shoot. As long as the shutter speed is not blinking, the standard exposure will be obtained.
Page 111 Caution If the “30"” shutter speed blinks, it indicates underexposure. Turn the < > dial to decrease the aperture value (open the aperture) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <...
Page 112 Depth-of-Field Preview Press the depth-of-field preview button to stop down the lens to the current aperture setting and check the area in focus (depth of field). Note The larger the aperture value, the wider the area (from the foreground to the background) in focus, but the darker the viewfinder display.
Page 113: M: Manual Exposure
M: Manual Exposure Exposure Compensation with ISO Auto In this mode, you set both the shutter speed and aperture value as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially available exposure meter. * <...
Page 114 Focus on the subject. (1) Standard exposure index (2) Exposure level mark (3) Brighter (+) (4) Darker (−) Press the shutter button halfway. The exposure value is displayed in the viewfinder and on the top LCD panel. To see how far the current exposure level < >...
Page 115 Set the exposure and take the picture. Check the exposure level indicator and set the desired shutter speed and aperture value. < > or < > is shown at the ends of the exposure level indicator if the exposure level exceeds ±3 stops from standard exposure. Exposure Compensation with ISO Auto If the ISO speed is set to “...
Page 116: Bulb: Long (Bulb) Exposures
bulb: Long (Bulb) Exposures In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. Use bulb exposures for night scenes, fireworks, astrophotography, and other subjects requiring long exposures. Set the shooting mode to <...
Page 117 Take the picture. (1) Minutes (2) Seconds (3) Hours The exposure will continue for as long as you keep the shutter button pressed completely. Elapsed exposure time is displayed on the top LCD panel. Caution Do not point the camera toward an intense light source, such as the sun or an intense artificial light source.
Page 118: Shooting And Recording
Shooting and Recording This chapter describes shooting and introduces menu settings on the shooting ([ ]) tab. • Still Photo Shooting • Still Photo Shooting (Live View Shooting) • Movie Recording...
Page 119: Still Photo Shooting
Still Photo Shooting • Tab Menus: Still Photo Shooting (Viewfinder Shooting) • White Balance • Custom White Balance • White Balance Correction • Color Space • Picture Style Selection • Picture Style Customization • Picture Style Registration • Clarity • Lens Aberration Correction •...
Page 120: Tab Menus: Still Photo Shooting (Viewfinder Shooting)
Tab Menus: Still Photo Shooting (Viewfinder Shooting) Shooting 1 White balance Set Custom WB WB Shift/Bkt. Color space (5) Picture Style • Picture Style Selection • Picture Style Customization • Picture Style Registration Clarity Lens aberration correction...
Page 121 Shooting 2 quality Img type/size ISO speed settings Auto Lighting Optimizer Long exp. noise reduction High ISO speed NR Highlight tone priority Shooting 3 Image review Release shutter without card Mirror lockup Dust Delete Data External Speedlite control Anti-flicker shoot.
Page 122 Shooting 4 Multiple exposure HDR PQ settings Live View shoot.
Page 123: White Balance
White Balance White Balance ] Auto White Balance ] Color Temperature White balance (WB) is for making the white areas look white. Normally, the Auto [ (Ambience priority) or [ ] (White priority) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with Auto, you can select the white balance to match the light source or set it manually by shooting a white object.
Page 124 (Approx.) Display Mode Color Temperature (K: Kelvin) Auto: Ambience priority 3000–7000 Auto: White priority Daylight 5200 Shade 7000 Cloudy, twilight, sunset 6000 Tungsten light 3200 White fluorescent light 4000 When using Flash Automatically set* Custom 2000–10000 Color temperature 2500–10000 * Applicable with Speedlites having a color temperature transmission function. Otherwise, it will be fixed to approx.
Page 125 ] Auto White Balance With [ ], you can slightly increase the intensity of the image's warm color cast when shooting a tungsten-light scene. If you select [ ], you can reduce the intensity of the image's warm color cast. Select [ : White balance].
Page 126 Caution Precautions when set to [ ] (White priority) The warm color cast of subjects may fade. When multiple light sources are included in the scene, the warm color cast of the picture may not be reduced. When using flash, the color tone will be the same as with [ ] (Ambience priority).
Page 127 ] Color Temperature Press the < > button ( Select < >. Watch the top LCD panel as you turn the < > dial to select < >. Set the value. Turn the < > dial to set the value. The color temperature can be set from approx.
Page 128 Caution When setting the color temperature for an artificial light source, set the white balance correction (magenta or green bias) as necessary. When setting < > to a value measured with a commercially available color temperature meter, take some test shots in advance and adjust the setting as needed to compensate for any difference between the color temperature meter and the camera.
Page 129: Custom White Balance
Custom White Balance Registering Custom White Balances Selecting and Shooting with Custom White Balances Naming Custom White Balances With custom white balance, you can manually set the white balance for the specific light source of the shooting location. Make sure to perform this procedure under the light source at the actual location of the shoot.
Page 130 Select a custom white balance number to be registered. Press < >. Turn the < > dial to select a number from 1 to 5 for < *>, then press < >. The custom white balance will be registered to the selected number.
Page 131 Shoot a plain white object. Look through the viewfinder and aim the outlined area over a plain white object, so that white fills the area. Focus manually and shoot with the standard exposure set for the white object. You can use any of the white balance settings. The custom white balance is registered to the camera.
Page 132 Note Custom white balances can also be registered as follows. 1.Press the < > button, then turn the < > dial to select < > ( 2.Next, turn the < > dial to select a number to register the custom white balance to.
Page 133 Select a custom white balance number to be registered. Press < >. Turn the < > dial to select a number from 1 to 5 for < *>, then press < >. The custom white balance will be registered to the selected number.
Page 134 Select [OK]. The custom white balance will be registered to the camera. Check the message and select [OK] to return to the screen in step 3. Caution These images cannot be selected in step 5: Images captured with the Picture Style set to [Monochrome], multiple-exposure images, HDR images, Frame Grab images from 4K movies, and images shot with another camera.
Page 135 Selecting and Shooting with Custom White Balances Select the custom white balance number. (1) Registered image On the [Set Custom WB] screen, select the number of the registered custom white balance. Select [Set as white balance]. The white balance setting changes to < *>.
Page 136 Note You can also select registered custom white balance numbers while viewing the top LCD panel. To do this, press the < > button, then turn the < > dial to select < >. Next, turn the < > dial to select a registered custom white balance number.
Page 137 Naming Custom White Balances You can add a name (caption) to the five registered custom white balances (custom white balance nos. 1–5). Select the custom white balance number. On the [Set Custom WB] screen, select the number of the registered custom white balance to add a name to.
Page 138 Enter text. Use the < > or < > dial to select a character, then press < > to enter it. By selecting [ ], you can change the input mode. To delete single characters, select [ ] or press the < >...
Page 139: White Balance Correction
White Balance Correction White Balance Correction White Balance Auto Bracketing You can correct the white balance that is set. This adjustment will have the same effect as using a commercially available color temperature conversion filter or color compensating filter. White Balance Correction Select [ : WB Shift/Bkt.].
Page 140 Set the white balance correction. Sample setting: A2, G1 Use < > to move the “■” mark on the screen to your preferred position. B is for blue, A for amber, M for magenta, and G for green. White balance is corrected in the direction you move the mark. On the right of the screen, [Shift] indicates the direction and correction amount, respectively.
Page 141 White Balance Auto Bracketing White balance bracketing (WB Bkt.) enables you to capture three images at once with different color tones. Setting the white balance bracketing amount In step 2 for “White Balance Correction”, when you turn the < > dial, the “■” mark on the screen will change to “■...
Page 142 Caution During white balance bracketing, the maximum burst for continuous shooting will be lower. Since three images are recorded for one shot, it takes longer to record the image to the card. Note You can also set white balance correction and AEB together with white balance bracketing.
Page 143: Color Space
Color Space Adobe RGB The range of reproducible colors is called the “color space.” For normal shooting, sRGB is recommended. Select [ : Color space]. Set a color space option. Select [sRGB] or [Adobe RGB], then press < >. Adobe RGB This color space is mainly used for commercial printing and other professional applications.
Page 144: Picture Style Selection
Picture Style Selection Picture Style Characteristics Symbols Just by selecting a preset Picture Style, you can obtain image characteristics effectively matching your photographic expression or the subject. Select [ : Picture Style]. Select a Picture Style.
Page 145 Picture Style Characteristics Auto The color tone will be adjusted automatically to suit the scene. The colors will look vivid for blue skies, greenery and sunsets, particularly in nature, outdoor, and sunset scenes. Note If the desired color tone is not obtained with [Auto], use another Picture Style. Standard The image looks vivid, sharp, and crisp.
Page 146 Monochrome Creates black-and-white images. Caution Color images cannot be recovered from JPEG images shot with the [Monochrome] Picture Style. Note < > is displayed on the top LCD panel when [Monochrome] is set. You can also set the camera to display < >...
Page 147 Symbols Icons on the Picture Style selection screen represent [Strength], [Fineness], and [Threshold] for [Sharpness] as well as [Contrast] and other parameters. The numbers indicate the values for these settings specified for the respective Picture Style. Sharpness Strength Fineness Threshold Contrast Saturation Color tone...
Page 148: Picture Style Customization
Picture Style Customization Settings and Effects Monochrome Adjustment You can customize any Picture Style by changing it from the default settings. For details on customizing [Monochrome], see Monochrome Adjustment. Select [ : Picture Style]. Select a Picture Style. Select the Picture Style to adjust, then press the < >...
Page 149 Select an item. For details on settings and effects, see Settings and Effects. Set the effect level. Press the < > button to save the adjusted setting and return to the Picture Style selection screen. Any settings you change from default values are displayed in blue.
Page 150 Note For movie recording, [Fineness] and [Threshold] for [Sharpness] cannot be set (not displayed). By selecting [Default set.] in step 3, you can restore the parameter settings of the respective Picture Style to the defaults. To shoot with the Picture Style you adjusted, first select the adjusted Picture Style, then shoot.
Page 151 Monochrome Adjustment Filter effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N:None Normal black-and-white image with no filter effects. Ye:Yellow Blue sky will look more natural, and white clouds will look crisper. Or:Orange The blue sky will look slightly darker.
Page 152: Picture Style Registration
Picture Style Registration You can select a base Picture Style such as [Portrait] or [Landscape], adjust it as desired, and register it under [User Def. 1] – [User Def. 3]. Useful when creating several Picture Styles with different settings. Picture Styles that you have registered on the camera using EOS Utility (EOS software, can also be modified here.
Page 153 Press < >. With [Picture Style] selected, press < >. Select a base Picture Style. Select the base Picture Style. Also select styles this way when adjusting styles registered to the camera with EOS Utility (EOS software). Select an item.
Page 154 Set the effect level. For details, see Picture Style Customization. Press the < > button to save the adjusted setting and return to the Picture Style selection screen. The base Picture Style will be indicated on the right of [User Def. *]. Blue style names in [User Def.
Page 155: Clarity
Clarity You can adjust image clarity, as determined by the contrast of image edges. Set toward the negative end to make images look softer or toward the positive end for a sharper appearance. Select [ : Clarity]. Set the effect level. Caution Setting clarity may darken or lighten the areas around boundaries in high-contrast images.
Page 156: Lens Aberration Correction
Lens Aberration Correction Peripheral Illumination Correction Distortion Correction Digital Lens Optimizer Chromatic Aberration Correction Diffraction Correction Vignetting, image distortion, and other issues may be caused by lens optical characteristics. The camera can compensate for these phenomena by using [Lens aberration correction]. Select [ : Lens aberration correction].
Page 157 Select [Enable]. Confirm that the name of the attached lens and (except for diffraction correction) [Correction data available] are displayed. If [Correction data not available] or [ ] is displayed, see Digital Lens Optimizer. Peripheral Illumination Correction Vignetting (dark image corners) can be corrected. Caution Depending on shooting conditions, noise may appear on the image periphery.
Page 158 Distortion Correction Distortion (image warping) can be corrected. Caution To correct distortion, the camera captures a narrower image area than the area seen in viewfinder shooting, which crops the image a little and slightly lowers the apparent resolution. For movie recording, [Distortion correction] will not appear. (Correction is not possible.) In Live View shooting, applying distortion correction may change the angle of view slightly.
Page 159 Digital Lens Optimizer Various aberrations from lens optical characteristics can be corrected, along with diffraction and low-pass filter-induced loss of resolution. If [Correction data not available] or [ ] is displayed by [Digital Lens Optimizer], you can use EOS Utility to add the lens correction data to the camera. For details, refer to the EOS Utility Instruction Manual.
Page 160 Chromatic Aberration Correction Chromatic aberration (color fringing around subjects) can be corrected. Note [Chromatic aberr corr] is not displayed when [Digital Lens Optimizer] is set to [Enable(Std)].
Page 161 General precautions for lens aberration correction Lens aberration correction cannot be applied to existing JPEG images. When using a non-Canon lens, setting the corrections to [Disable] is recommended even if [Correction data available] is displayed. The amount of correction (except diffraction correction) is less for lenses that do not provide distance information.
Page 162: Image Quality
Image Quality Image Size Selection RAW Images Guide to Image Quality Settings Maximum Burst for Continuous Shooting JPEG/HEIF Quality Image Size Selection You can specify , , or for JPEG images, for HEIF images, and for RAW images. Image size can be set in either of the following ways. Setting size via the rear LCD panel Press the <...
Page 163 Select the desired image size. Turn the < > dial to select the image size. Both RAW and JPEG images will be captured when are displayed together. Both RAW and HEIF images will be captured when and / are displayed together. Turn the <...
Page 164 Set the image size. Standard/Auto switch card/Record to multiple For RAW images, turn the < > dial, and for JPEG images, turn the < > dial. Press < > to set it. Record separately When [ Record func.] in [ : Record func+card/folder sel.] is set to [Rec.
Page 165 Note In the viewfinder, maximum display of the number of shots available is 1999. is set automatically if you set both RAW and JPEG/HEIF to [ Two versions of each shot are recorded at your specified image quality when you have selected both RAW and JPEG/HEIF.
Page 166 RAW images captured by this camera. If a previous version of DPP Ver. 4.x is installed on your computer, obtain and install the latest version of DPP from the Canon website to update it ( ), which will overwrite the previous version.
Page 167 Guide to Image Quality Settings Performance Data for details on file size, number of shots available, maximum burst, and other estimated values.
Page 168 Maximum Burst for Continuous Shooting Approximate maximum burst is shown at the right in the viewfinder, on the Quick Control screen, and at the bottom of the Custom Quick Control screen. Caution Maximum burst is shown even without a card in the camera, so make sure a card is inserted before shooting.
Page 169 JPEG/HEIF Quality Select [ quality]. Select the desired image size. Select the image size, then press < >. Set the desired quality (compression). Select the number, then press < >. Higher numbers offer higher quality (lower compression). Quality of 6–10 is indicated by < >, and 1–5, by <...
Page 170 Note The higher the quality, the fewer shots will be available. In contrast, the lower the quality, the more shots will be available.
Page 171: Iso Speed Settings For Still Photos
ISO Speed Settings for Still Photos ISO Speed Range When Set Manually ISO Speed Range Used With ISO Auto Minimum Shutter Speed for ISO Auto Set the ISO speed (image sensor's sensitivity to light) to suit the ambient light level. For details on ISO speed when recording movies, see ISO Speed in <...
Page 172 Caution Image noise (dots of light or banding) and irregular colors may increase and apparent resolution may decrease at H1, H2, or H3 (equivalent to ISO 204800, 409600, and 819200, respectively), because these are expanded ISO speeds. Because L (equivalent to ISO 50) is an expanded ISO speed setting, the dynamic range will be somewhat narrower compared to the standard setting.
Page 173 ISO Speed Range When Set Manually You can set the manual ISO speed setting range (minimum and maximum limits). You can set the minimum limit within L (equivalent to ISO 50) to H2 (equivalent to ISO 409600), and the maximum limit within ISO 100 to H3 (equivalent to ISO 819200). Select [ ISO speed settings].
Page 174 Set [Maximum]. Select the [Maximum] box, then press < >. Select the ISO speed, then press < >. Select [OK].
Page 175 ISO Speed Range Used With ISO Auto You can set the automatic ISO speed range for ISO Auto within ISO 100–102400. The minimum can be set within ISO 100–51200 and the maximum within ISO 200–102400, in 1- stop increments. Select [Auto range]. Set [Minimum].
Page 176 Set [Maximum]. Select the [Maximum] box, then press < >. Select the ISO speed, then press < >. Select [OK]. Note The [Minimum] and [Maximum] settings will also function as the minimum and maximum speeds for ISO speed safety shift (...
Page 177 Minimum Shutter Speed for ISO Auto To prevent shutter speeds from being set too low automatically, you can set the minimum shutter speed for ISO Auto. This is effective in < > or < > mode when shooting subjects in motion with a wide- angle lens, or when using a telephoto lens.
Page 178 Set the desired minimum shutter speed. Automatically set If you select [Auto], turn the < > dial to set the difference relative to standard speed (toward Slower or Faster), then press < >. Manually set If you select [Manual], turn the < >...
Page 179: Auto Lighting Optimizer
Auto Lighting Optimizer Brightness and contrast can be corrected automatically if shots look dark or contrast is too low or high. Select [ : Auto Lighting Optimizer]. Set a correction option. Caution Noise may increase and apparent resolution may change, under some shooting conditions.
Page 180 Note To enable [ : Auto Lighting Optimizer] to be set even in < > and < > modes, press the < > button in step 2 to clear the checkmark [ ] for [Disabled in M or B modes].
Page 181: Long Exposure Noise Reduction
Long Exposure Noise Reduction Noise that tends to occur in long exposures at shutter speeds of one sec. or slower can be reduced. Select [ : Long exp. noise reduction]. Set a reduction option. Auto For images exposed for 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected.
Page 182 Caution With [Auto] or [Enable] set, noise reduction after you shoot may take as long as exposure for the shot. Images may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting. “ ” is displayed as noise is reduced, and no Live View image is displayed until processing is finished, when you can shoot again.
Page 183: High Iso Speed Noise Reduction
High ISO Speed Noise Reduction You can reduce the image noise generated. This function is especially effective when shooting at high ISO speeds. When shooting at low ISO speeds, the noise in the darker parts of the image (shadow areas) can further be reduced. Select [ : High ISO speed NR].
Page 184: Highlight Tone Priority
Highlight Tone Priority You can reduce overexposed, clipped highlights. Select [ : Highlight tone priority]. Set an option. [Enable]: Improves gradation in highlights. The gradation between the grays and highlights becomes smoother. [Enhanced]: Reduces overexposed highlights even more than [Enable], under some shooting conditions. Caution Noise may increase slightly.
Page 185: Image Review
Image Review To keep the image displayed immediately after you shoot, set to [Hold], and if you prefer not to have the image displayed, set to [Off]. Select [ : Image review]. Set a time option. Note When [Hold] is set, images are displayed as long as the time set in [ : Auto power off].
Page 186: Shutter Release Without Card
Shutter Release Without Card You can set the camera not to shoot unless there is a card in the camera. The default setting is [Enable]. Select [ : Release shutter without card]. Select [Disable].
Page 187: Mirror Lockup
Mirror Lockup Mirror lockup keeps the mirror up in viewfinder shooting to reduce blur from mirror movement. Useful when shooting close-ups (macro photography), using a super telephoto lens, shooting at slow shutter speeds, etc. Select [ : Mirror lockup]. Select an item. Select [Enable] or [Enable:Mirror down w/ ], then press <...
Page 188 Press the shutter button completely again. The camera shoots. When set to [Enable], the mirror is lowered after shooting. When set to [Enable:Mirror down w/ ], the mirror remains up after shooting. To lower the mirror, press < >. Caution Do not point the camera toward an intense light source, such as the sun or an intense artificial light source.
Page 189: Dust Delete Data Acquisition
Dust Delete Data Acquisition Preparation Dust Delete Data Appending Dust Delete Data used to erase dust spots can be appended to images in case sensor cleaning leaves dust on the sensor. The Dust Delete Data is used by Digital Photo Professional (EOS software) to erase the dust spots automatically.
Page 190 Select [OK]. After the automatic self-cleaning of the sensor is performed, a message will appear. Although there will be a mechanical sound of the shutter during the cleaning, no picture is taken.
Page 191 Shoot a plain white object. Shoot with a plain white object (such as a new sheet of white paper) filling the screen, at a distance of 20–30 cm (0.7–1.0 ft.). Since the image will not be saved, the data can still be obtained even if there is no card in the camera.
Page 192 Dust Delete Data Appending The camera will append the Dust Delete Data obtained to all shots from now on. Acquiring Dust Delete Data before shooting is recommended. For details about using Digital Photo Professional (EOS software) to erase dust spots automatically, refer to the Digital Photo Professional Instruction Manual.
Page 193: Shooting With Speedlites
Shooting With Speedlites EL/EX Series Speedlites for EOS Cameras Canon Speedlites Other Than the EL/EX Series Non-Canon Flash Units EL/EX Series Speedlites for EOS Cameras Features of EL/EX series Speedlites (sold separately) can be used in flash photography with the camera.
Page 194 Note You can also set flash exposure compensation on the Quick Control screen ( ) or in the [Flash function settings] setting of [ : External Speedlite control] (...
Page 195 Canon Speedlites Other Than the EL/EX Series With an EZ/E/EG/ML/TL series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output only. Set the camera's shooting mode to < > or < > and adjust the aperture value before shooting.
Page 196 Non-Canon Flash Units Sync speed The camera can synchronize with non-Canon compact flash units at up to 1/250 sec. With large studio flash units, the flash duration is longer than that of a compact flash unit and varies depending on the model. Before shooting, confirm that flash sync is performed correctly by taking some test shots at a sync speed of approx.
Page 197 Note Metered manual flash exposure This feature enables you to set the flash exposure level manually for close-up shots. Using a Speedlite with manual flash mode and a standard 18% gray card, follow these steps. 1. Configure the camera and Speedlite settings. •...
Page 198: Flash Function Settings
Flash Function Settings Flash Firing E-TTL Balance E-TTL II Flash Metering Continuous Flash Control Flash Sync Speed in Av Mode Flash Function Settings Flash Custom Function Settings Clearing Flash Function Settings/Clearing All Speedlite Custom Functions Functions of EL/EX Series Speedlites compatible with flash function settings can be set via a camera menu screen.
Page 199 Select an item. Flash Firing To enable flash photography, set to [Enable]. To enable only the AF-assist beam of the Speedlite, set to [Disable].
Page 200 E-TTL Balance You can set your preferred appearance (balance) for flash shots. This setting enables you to adjust the ratio of ambient light to Speedlite light output. Set the balance to [Ambience priority] to lower the proportion of flash output and uses ambient light to produce lifelike shots with a natural mood.
Page 201 E-TTL II Flash Metering Set to [Eval (FacePrty)] for flash metering suitable for shots of people. The continuous shooting speed for high-speed continuous shooting is slower than when [Evaluative] or [Average] is selected. Set to [Evaluative] for flash metering that emphasizes firing in continuous shooting. If [Average] is set, the flash exposure will be averaged for the entire metered scene.
Page 202 Continuous Flash Control Set to [E-TTL each shot] to perform flash metering for each shot. Set to [E-TTL 1st shot] to perform flash metering for only the first shot before continuous shooting. The flash output level for the first shot is applied to all subsequent shots. Useful when prioritizing continuous shooting speed without recomposing shots.
Page 203 Flash Sync Speed in Av Mode You can set the flash-sync speed for flash photography in < > mode. : Auto The shutter speed is set automatically within a range of 1/250 sec. to 30 sec. to suit the brightness. High-speed sync is also possible. : 1/250-1/60sec.
Page 204 Flash Function Settings The information displayed on the screen, position of display, and available options vary depending on the Speedlite model, its Custom Function settings, the flash mode, and other factors. For details on the Speedlite's functions, refer to the Speedlite's Instruction Manual. Sample display Flash mode Wireless functions/...
Page 205 Flash mode You can select the flash mode to suit your desired flash photography. [E-TTL II flash metering] is the standard mode of EL/EX series Speedlites for automatic flash photography. [Manual flash] is for setting the Speedlite's [Flash output level] yourself. [CSP] (Continuous shooting priority mode) is available when using a compatible external Speedlite.
Page 206 Wireless functions You can use radio or optical wireless transmission to shoot with wireless multiple-flash lighting. For details on wireless flash, refer to the Instruction Manual of a Speedlite compatible with wireless flash photography. Firing ratio control (RATIO) With a macro flash, you can set the firing ratio control. For details on firing ratio control, refer to the Instruction Manual of the macro flash.
Page 207 Shutter synchronization Normally, set this to [First-curtain synchronization] so that the flash fires immediately after the shooting starts. Set to [Second-curtain synchronization] and use low shutter speeds for natural-looking shots of subject motion trails, such as car headlights. Set to [High-speed synchronization] for flash photography at higher shutter speeds than the maximum flash sync shutter speed.
Page 208 Flash exposure bracketing Speedlites equipped with flash exposure bracketing (FEB) can change the external flash output automatically as three shots are taken at once.
Page 209 Flash Custom Function Settings For details on the Speedlite's Custom Functions, refer to the Instruction Manual of the Speedlite. Select [Flash C.Fn settings]. Set the desired functions. Select the number. Select an item. Caution With an EX series Speedlite, the Speedlite will always fire at full output if the [Flash metering mode] Custom Function is set to [TTL flash metering] (autoflash).
Page 210 Clearing Flash Function Settings/Clearing All Speedlite Custom Functions Select [Clear settings]. Select the settings to be cleared. Select [Clear flash settings] or [Clear all Speedlite C.Fn's]. Select [OK] on the confirmation screen to clear all flash settings or Custom Function settings.
Page 211: Anti-Flicker Shooting
Anti-Flicker Shooting Uneven exposure and color may result if you shoot at fast shutter speeds under flickering light sources such as fluorescent lights, due to uneven vertical exposure. Anti-flicker shooting enables viewfinder shooting at moments when exposure and colors are less affected by flickering.
Page 212 Caution When [Enable] is set and you shoot under a flickering light source, the shutter- release time lag may become longer. Also, the continuous shooting speed may become slower, and the shooting interval may become irregular. Not applied to mirror lockup shots, Live View shooting, or movie recording. Flicker at a frequency other than 100 Hz or 120 Hz cannot be detected.
Page 213: Multiple Exposures
Multiple Exposures Merging Multiple Exposures with a RAW Image Recorded on the Card Checking and Deleting Multiple Exposures During Shooting You can shoot multiple (2–9) exposures to merge into a single image. In Live View shooting, you can see in real time how the exposures are merged when you shoot multiple-exposure images.
Page 214 Set [Multiple exposure]. Select an option, then press < >. To exit shooting multiple exposures, select [Disable]. On:Func/Ctrl Convenient when shooting multiple exposures gradually as you check the results. During continuous shooting, the continuous shooting speed will decrease greatly. On:ContShtng Used for continuous multiple exposures of moving subjects.
Page 215 Set [Multi-expos ctrl]. Select a merging option, then press < >. Additive The exposure of each single image captured is added cumulatively. Based on [No. of exposures], set negative exposure compensation. Follow these basic guidelines to set the exposure compensation amount.
Page 216 Set [No. of exposures]. Select the number of exposures, then press < >. Specify the images to save. To save all single exposures and the multiple-exposure image, select [All images] and press < >. To save only the multiple-exposure image, select [Result only] and press <...
Page 217 Set [Continue Mult-exp]. Select an option, then press < >. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends. With [Continuously], multiple-exposure shooting continues until the setting in step 2 is set to [Disable]. Shoot the first exposure. When [On:Func/Ctrl] is set, the captured image will be displayed.
Page 218 Shoot the next exposures. Images captured so far are displayed merged in Live View shooting. For only Live View image display, press the < > button repeatedly. To view the multiple-exposure image so far, check exposure, and see how the images will be merged, hold down the depth-of-field preview button (or the button assigned to [Depth-of-field preview] in [ Custom Controls] ) in Live View shooting.
Page 219 Merging Multiple Exposures with a RAW Image Recorded on the Card You can select a RAW image recorded on the card as the first single exposure. The selected RAW image will remain intact. Select [Select image for multi. expo.]. Select the first image. Turn the <...
Page 220 Caution JPEG/HEIF images cannot be selected. These images cannot be selected as the first single exposure: images shot with : Highlight tone priority] set to [Enable] or [Enhanced], or images with cropping information. [Disable] is applied for [ : Lens aberration correction] and [ : Auto Lighting Optimizer], regardless of the settings of the image selected as the first single exposure.
Page 221 Checking and Deleting Multiple Exposures During Shooting To view the multiple-exposure image so far, check exposure, and see how the images are layered, you can press the < > button before you finish shooting your specified number of exposures (when [On:Func/Ctrl] is set, but not with [On:ContShtng]). Pressing the <...
Page 222 Are there any restrictions on the image quality? All single exposures and the multiple-exposure image are captured at your specified image quality. Can I merge images recorded on the card? With [Select image for multi. expo.], you can select the first single exposure from the images recorded on the card ( ).
Page 223: Hdr Pq Settings
HDR PQ Settings PQ in HDR PQ refers to the gamma curve of the input signal for displaying HDR images. HDR PQ settings enable the camera to produce HDR images conforming to the PQ specification defined in ITU-R BT.2100 and SMPTE ST.2084 (with actual display depending on monitor performance).
Page 224 Set [HDR assist disp: shooting]. Converted images are displayed on the screen in Live View shooting, giving an impression similar to how they would appear on an HDR display device. Select [Exposure prior. (mid-tones)] or [Tones prior. (highlights)]. ] Exposure prior. (mid-tones) Provides reference display that emphasizes exposure of subjects (such as people) with intermediate brightness.
Page 225 Set [HDR assist disp: playback]. Converted images are displayed on the screen for playback, giving an impression similar to how they would appear on an HDR display device. Select [Exposure prior. (mid-tones)] or [Tones prior. (highlights)]. ] Exposure prior. (mid-tones) Provides reference display that emphasizes exposure of subjects (such as people) with intermediate brightness.
Page 226: Metering Mode Selection
Metering Mode Selection Multi-Spot Metering You can select one of four methods to measure the subject brightness. Press the < > button ( Select the metering mode. Watch the top LCD panel or look through the viewfinder as you turn the <...
Page 227 Evaluative metering General-purpose metering mode suited even for backlit subjects. The camera adjusts the exposure automatically to suit the scene. Partial metering Effective where there are much brighter lights around the subject due to backlight, etc. Spot metering Effective when metering a specific part of the subject. The spot metering circle will be displayed in the viewfinder.
Page 228 Multi-Spot Metering By specifying multiple areas for spot metering, you can determine an overall exposure level based on the average of your selected areas. Multi-spot metering is available in < >, < >, and < > modes. Set the metering mode to < >...
Page 229: Manual Exposure Compensation
Manual Exposure Compensation Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. For details on exposure compensation when < > mode and ISO Auto are both set, see M: Manual Exposure. Check the exposure. Press the shutter button halfway ( ) and check the exposure level indicator.
Page 230 Take the picture. To cancel exposure compensation, set the exposure level < > to the standard exposure index (< >). Caution If [ : Auto Lighting Optimizer] ( ) is set to any setting other than [Disable], the image may still look bright even if decreased exposure compensation is set to darken images.
Page 231: Auto Exposure Bracketing (Aeb)
Auto Exposure Bracketing (AEB) In exposure bracketing, three consecutive images are captured at different exposures within your specified range of up to ±3 stops (in 1/3-stop increments) by automatically adjusting the shutter speed or aperture value. This is called AEB. * AEB stands for Auto Exposure Bracketing.
Page 232 Set the AEB range. (1) AEB amount (2) AEB range Turn the < > or < > dial to set the AEB range. Take the picture. Standard exposure Decreased exposure Increased exposure Three bracketed shots are taken, according to the specified drive mode, in this sequence: Standard exposure, decreased exposure, and increased exposure.
Page 233 Note During AEB shooting, the < > icon in the viewfinder and the < > icon on the top LCD panel blink. If the drive mode is set to < >, press the shutter button three times for each shot. In <...
Page 234: Exposure Lock (Ae Lock)
Exposure Lock (AE Lock) AE Lock Effects You can lock the exposure when you want to set the focus and exposure separately or when you will take multiple shots at the same exposure setting. Press the < > button to lock the exposure, then recompose and take the picture.
Page 235 Recompose and take the picture. The AE lock exposure value and current exposure value are shown in real time at right in the viewfinder. When you are to take more pictures while maintaining the AE lock, keep holding down the < >...
Page 236: Using The Eyepiece Shutter
Using the Eyepiece Shutter Light that enters the viewfinder if you shoot without looking through it (in self-timer shooting, bulb exposures, or remote switch shooting) may cause shots to be underexposed. To prevent this, slide the eyepiece shutter lever as shown by the arrow to cover the viewfinder eyepiece.
Page 237: Using A Remote Switch
Using a Remote Switch You can connect Remote Switch RS-80N3, Timer Remote Controller TC-80N3 (both sold separately), or other optional EOS shooting accessories equipped with an N3-type terminal For operating instructions, refer to the Instruction Manual of the accessory. Open the terminal cover. Connect the plug to the remote control terminal.
Page 238: Still Photo Shooting (Live View Shooting)
Still Photo Shooting (Live View Shooting) You can shoot while viewing live images on the camera screen. This is called “Live View shooting.” • Tab Menus: Still Photo Shooting (Live View Shooting) • Live View Shooting • Shutter Mode • Exposure Simulation •...
Page 239: Tab Menus: Still Photo Shooting (Live View Shooting)
Tab Menus: Still Photo Shooting (Live View Shooting) Shooting 1 White balance Set Custom WB WB Shift/Bkt. Color space (5) Picture Style • Picture Style Selection • Picture Style Customization • Picture Style Registration Clarity Lens aberration correction...
Page 240 Shooting 2 quality Img type/size ISO speed settings Auto Lighting Optimizer Long exp. noise reduction High ISO speed NR Highlight tone priority Shooting 3 Image review Release shutter without card Dust Delete Data External Speedlite control...
Page 241 Shooting 4 Shutter mode Multiple exposure HDR PQ settings Expo. simulation Metering timer...
Page 242: Live View Shooting
Live View Shooting Set the Live View shooting/Movie shooting switch to < >. Display the Live View image. Press the < > button. Live View images are displayed nearly as bright as your shots. Select a shooting mode. Press the < >...
Page 243 Focus on the subject. When you press the shutter button halfway, the camera will focus with the current AF method ( You can also tap the screen to select the face or subject. Take the picture. Press the shutter button completely. Press the <...
Page 244 Note The field of view is approx. 100% (with image size set to JPEG/ ). The camera will turn off automatically if left idle for the time set in [ : Auto power off] ( ). When the setting is set to [Disable], the camera exits Live View shooting automatically in approx.
Page 245: Shutter Mode
Shutter Mode You can choose the method of shutter release. Select [ : Shutter mode]. Select an option. Mechanical Shooting activates the mechanical shutter. Recommended when shooting with the aperture of a bright lens wide open. Elec. 1st-curtain Shooting only activates the second-curtain shutter. The shutter is quieter than with [Mechanical].
Page 246 Zooming during continuous shooting may cause changes in exposure even at the same f/number. For details, refer to the Canon website. [Elec. 1st-curtain] is used for bulb exposures. AEB shooting and flash photography are not available.
Page 247: Exposure Simulation
Exposure Simulation With exposure simulation, image brightness more closely matches the actual brightness (exposure) of your shots. Select [ : Expo. simulation]. Set an option. Enable ( The displayed image brightness will be close to the actual brightness (exposure) of the resulting image.
Page 248: Metering Timer
Metering Timer You can set how long the metering timer runs (which determines the duration of exposure display/AE lock) after it is triggered by an action such as pressing the shutter button halfway. Select [ : Metering timer]. Set a time option.
Page 249: General Live View Shooting Precautions
General Live View Shooting Precautions Caution Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera's internal components. Image quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
Page 250 Live View image Under low- or bright-light conditions, the displayed image may not reflect the brightness of the captured image. Although noise may be noticeable in Live View images under low light (even at low ISO speeds), there will be less noise in your shots, due to differences in image quality between Live View images and captured images.
Page 251: Movie Recording
• Tab Menus: Movie Recording • Movie Recording • Movie Recording Quality • Sound Recording • Time Code • Canon Log Settings • Movie Digital IS • Other Menu Functions • General Movie Recording Precautions...
Page 252: Tab Menus: Movie Recording
Tab Menus: Movie Recording Shooting 1 White balance Set Custom WB WB correction (4) Picture Style • Picture Style Selection • Picture Style Customization • Picture Style Registration Clarity Lens aberration correction Shooting 2 ISO speed settings • ISO Speed in < >, <...
Page 253 Shooting 3 Movie rec quality Sound recording Canon Log settings Movie digital IS Auto slow shutter Shooting 4 Metering timer Time code HDMI display...
Page 254: Movie Recording
Movie Recording Program AE Shutter-Priority AE Aperture-Priority AE ISO Speed in < >, < >, and < > Modes Manual Exposure Recording ISO Speed in < > Mode Shutter Speed Still Photo Shooting Information Display (Movie Recording) Program AE In < >...
Page 255 Set the recording mode to < >. Press the < > button, then turn the < > or < > dial for selection. Focus on the subject. Before recording a movie, focus with AF ( ) or manual focus ( By default, [ : Movie Servo AF] is set to [Enable] so that the camera always keeps focusing (...
Page 256 Record the movie. Press the < > button to start recording a movie. While the movie is being recorded, the [ REC] icon (1) will be displayed in the upper right of the screen. Sound is recorded with the movie microphone (2). To stop recording the movie, press the <...
Page 257 Shutter-Priority AE < > recording mode enables you to set your preferred shutter speed for movies. ISO speed and aperture values are set automatically to suit the brightness and obtain standard exposure. Set the Live View shooting/Movie shooting switch to < >.
Page 258 Set the shutter speed (1). Turn the < > dial to set it. The available shutter speeds vary depending on the frame rate. Focus and record the movie. The procedure is the same as steps 3 and 4 for Program...
Page 259 Caution Avoid adjusting shutter speed while recording movies, which will record changes in exposure. When recording a movie of a moving subject, a shutter speed of approx. 1/25 sec. to 1/125 sec. is recommended. The faster the shutter speed, the less smooth the subject's movement will look.
Page 260 Aperture-Priority AE < > recording mode enables you to set your preferred aperture value for movies. ISO speed and shutter speed are set automatically to suit the brightness and obtain standard exposure. Set the Live View shooting/Movie shooting switch to < >.
Page 261 Set the aperture value (1). Turn the < > dial to set it. Focus and record the movie. The procedure is the same as steps 3 and 4 for Program Caution Avoid adjusting the aperture value while recording movies, which will record changes in exposure caused by aperture adjustment.
Page 262 Note Notes for < >, < >, and < > modes You can lock the exposure (AE lock) by pressing the < > button. After applying AE lock during movie recording, you can cancel it by pressing the < > button. (AE lock setting is retained until you press the <...
Page 263 ISO Speed in < >, < >, and < > Modes ISO speed is set automatically. See ISO Speed in Movie Recording.
Page 264 Manual Exposure Recording You can manually set the shutter speed, aperture value, and ISO speed for movie recording. Set the Live View shooting/Movie shooting switch to < >. Set the recording mode to < >. Press the < > button, then turn the < >...
Page 265 Set the shutter speed (1) and aperture value (2). Press the shutter button halfway and check the exposure level indicator. To set the shutter speed, turn the < > dial. To set the aperture value, turn the < > dial. The available shutter speeds vary depending on the frame rate.
Page 266 Caution ISO speed cannot be expanded to L, H2, or H3 (equivalent to ISO 50, ISO 409600, and ISO 819200, respectively) in movie recording. During movie recording, avoid changing the shutter speed, aperture value, or ISO speed, which may record changes in the exposure or create more noise at high ISO speeds.
Page 267 ISO Speed in < > Mode You can set the ISO speed manually or select [ ] to set it automatically. For details on ISO speed, see ISO Speed in Movie Recording.
Page 268 Shutter Speed Available shutter speeds in < > and < > mode vary depending on the frame rate of your specified movie recording quality. Shutter Speed (Sec.) Frame Rate Normal Movie Recording High Frame Rate Movie Recording 1/4000–1/125 – 1/4000–1/100 1/4000–1/8 –...
Page 269 Still Photo Shooting Still photos cannot be taken during movie recording. To take still photos, stop the movie recording and perform viewfinder shooting or Live View shooting.
Page 270 Information Display (Movie Recording) For details on the icons on the movie recording screen, see Information Display. Caution Precautions for movie recording Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera's internal components.
Page 271 Note Notes for movie recording Each time you record a movie, a new movie file is created on the card. Field of view (coverage) is approx. 100%. Focusing is also possible by pressing the < > button. To enable starting/stopping movie recording by pressing the shutter button completely, set [Fully-press] for [ : Shutter btn function for movies] to [Start/ stop mov rec] ( Monaural sound is recorded with the built-in microphone for movie recording (...
Page 272: Movie Recording Quality
Movie Recording Quality Movie Recording Size 4K Movie Recording Image Area Cards That Can Record Movies High Frame Rate Movie Files Exceeding 4 GB Total Movie Recording Time and File Size Per Minute Movie Recording Time Limit You can set the image size, frame rate, compression method, and recording format in the [Movie rec.
Page 273 Caution The card's writing/reading speeds required for recording movies (card performance requirements) vary depending on the movie recording quality. Before recording movies, see Cards that can record movies to check card performance requirements. Movie Recording Size Image size Image Size Aspect Ratio 5472×2886 17:9...
Page 274 4K Movie Recording Recording 4K movies requires a stable card with a fast writing speed. For details, see Cards That Can Record Movies. 4K or High Frame Rate movie recording greatly increases the processing load, which may increase the internal camera temperature faster or higher than for regular movies. If a red icon appears during movie recording, the card may be hot, so stop recording the movie and let the camera cool down before removing the card.
Page 275 Image Area The movie image area varies depending on factors such as movie recording quality settings and the lens used. (1) Still images (5472×3648) (JPEG L) (1920×1080) (3) RAW movies (5472×2886)/ (4096×2160) (3840×2160) (4096×2160) Caution Recording with Movie digital IS ( ) further crops the image around the center of the screen.
Page 276 Compression method ] ALL-I (For editing/I-only) Compresses each frame, one at a time, for recording. Although file sizes are larger than with IPB (Standard), movies are more suitable for editing. ] IPB (Standard) Compresses multiple frames at a time efficiently for recording. File sizes are smaller than with ALL-I (For editing), which enables movie recording over longer periods (with a card of the same capacity).
Page 277 Commercially available software may not be able to display RAW movies recorded by this camera. For compatibility information, contact the software manufacturer. To prioritize gradation in highlights, set Canon Log to [On]. For RAW movies, consider setting the color matrix to CINEMA EOS Original.
Page 278 Cards That Can Record Movies For details on cards that can record at each level of movie recording quality, check the Canon website. Test cards by recording a few movies to make sure they can record correctly at your specified size (...
Page 279 High Frame Rate You can record Full HD movies at a high frame rate of 119.9 fps or 100.0 fps. This is ideal for recording movies that will be played back in slow motion. The maximum recording time per movie is 7 min. 29 sec. Movies are recorded in quality.
Page 280 Movie Files Exceeding 4 GB Even if you record a movie exceeding 4 GB, you can keep recording without interruption. Caution When importing movie files exceeding 4 GB to a computer, use either EOS Utility or a card reader ( ).
Page 281 Total Movie Recording Time and File Size Per Minute Total movie recording time and file size per minute.
Page 282 Movie Recording Time Limit When recording non-High Frame Rate movies The maximum recording time per movie is 29 min. 59 sec. Once 29 min. 59 sec. is reached, recording automatically stops. You can start recording a movie again by pressing the < >...
Page 283: Sound Recording
Sound Recording Sound Recording/Sound-Recording Level Wind Filter Attenuator You can record movies while recording sound with the built-in monaural microphone or an external stereo microphone. You can also freely adjust the sound-recording level. Use [ : Sound recording] to set sound recording functions. Caution Sounds from Wi-Fi operations may be captured with built-in or external microphones.
Page 284 Note Audio is also output when the camera is connected to televisions via HDMI, except when [Sound rec.] is set to [Disable]. In case of feedback from television audio output, move the camera away from the television or turn down the volume. The sound volume balance between L (left) and R (right) cannot be adjusted.
Page 285 Wind Filter Set to [Enable] to reduce wind noise when there is wind outdoors. Only activated when the camera's built-in microphone is used. When the wind filter function takes effect, part of the low bass sounds will also be reduced.
Page 286 Attenuator Automatically suppresses sound distortion caused by loud noises. Even if [Sound rec.] is set to [Auto] or [Manual] for recording, sound distortion may still result if there is a very loud sound. In this case, setting it to [Enable] is recommended. Microphone Normally, monaural sound is recorded with the built-in movie microphone.
Page 287: Time Code
Time Code Count Up Start Time Setting Movie Recording Count Movie Play Count HDMI Drop Frame Time codes record the time automatically as movies are recorded. Time codes always record elapsed hours, minutes, seconds, and frames. They are mainly used when movies are edited.
Page 288 Count Up Rec run The time code advances only during movie recording. Time codes in each movie file recorded continue from the last time code in the previous file. Free run The time code keeps advancing, even when you are not recording. Caution When set to [Free run], time codes are not added to High Frame Rate movies that you record.
Page 289 Start Time Setting You can set the initial time of the time code. Manual input setting Enables you to set any starting hour, minute, second, and frame. Reset Resets the time set with [Manual input setting] or [Set to camera time] to “00:00:00.” or “00:00:00:”...
Page 290 Movie Recording Count You can select how time is displayed on the movie recording screen. Rec time Displays the elapsed time since movie recording began. Time code Displays the time code during movie recording.
Page 291 Movie Play Count You can select how time is displayed on the movie playback screen. Rec time Displays the recording or playback time during movie playback. Time code Displays the time code during movie playback. Note Time codes are always recorded to movie files (except for High Frame Rate movies set to [Free run]), regardless of the [Movie rec count] setting.
Page 292 HDMI Time code Time codes can be added to movies as you record them to an external device via HDMI. • Off No time code is added to HDMI video output. • On Time codes are added to HDMI video output. When [On] is set, [Rec Command] is displayed.
Page 293 Drop Frame The time code's frame count will cause a discrepancy between the actual time and the time code if the frame rate is set to (119.9 fps), (59.94 fps), or (29.97 fps). The discrepancy is corrected automatically when [Enable] is set. This correction function is called “drop frame.”...
Page 294: Canon Log Settings
To work with Canon Log movies in postproduction, you can apply look-up tables (LUTs). LUT data can be downloaded from the Canon website. Select [ : Canon Log settings].
Page 295 Select [On] ( Set the options as desired. [View Assist.], [Color Matrix], [Characteristics], and [Color space]. Canon Log Enables 10-bit recording of Canon Log movies to the card. Movies can also be recorded to an external device that supports 10-bit recording.
Page 296 When played on the camera, these movies may look darker and have lower contrast than movies recorded with a Picture Style applied, due to Canon Log image characteristics, which are intended to ensure a wide dynamic range. For clearer display that makes it easier to check details, set [View Assist.] to [On].
Page 297 +4: Toward magenta * Reds, greens, and blues cannot be adjusted separately. Color space [Color space] can be set when [Canon Log] is set to [On] and [Color Matrix] to [Neutral]. Choose [BT.709] or [BT.2020] as the color space for HDMI output.
Page 298 Manually setting the ISO speed to 100–320 will make the dynamic range narrower. Canon Log offers a dynamic range of approx. 800% at ISO 400 or higher. ISO 100, 125, 160, 200, 250, and 320 are expanded ISO speeds. [ ] is displayed when...
Page 299 Canon Log Image Quality Noise may increase slightly. Caution General Canon Log shooting precautions With Canon Log, autofocusing may be more difficult for subjects under low light, or for low-contrast subjects. Canon Log 2 and Canon Log 3 are not supported. Note Playing movies recorded with Canon Log View Assist is not used during movie playback.
Page 300: Movie Digital Is
Movie Digital IS The camera's Movie digital IS feature reduces camera shake as movies are recorded. Movie digital IS can provide effective stabilization even when your lens is not equipped with Image Stabilizer. When using a lens equipped with Image Stabilizer, set the lens's Image Stabilizer switch to <...
Page 301 Depending on the subject and shooting conditions, the subject may blur noticeably (the subject momentarily looks out of focus) due to the effects of the Movie digital When using a TS-E lens, fish-eye lens, or non-Canon lens, setting Movie digital IS to [Disable] is recommended.
Page 302: Other Menu Functions
Other Menu Functions Lens aberration correction Peripheral illumination, chromatic aberration, and diffraction can be corrected as you record movies. For details on lens aberration correction, see Lens Aberration Correction.
Page 303 ISO speed settings • ISO speed In < > mode, you can set the ISO speed manually. You can also select ISO Auto. • ISO speed range For < > mode, you can set the manual ISO speed setting range (minimum and maximum limits).
Page 304 Auto slow shutter You can choose whether to record movies that are brighter and less affected by image noise than when set to [Disable] by automatically slowing the shutter speed under low light. Available in < > or < > recording mode. Applies when the frame rate of the movie recording size is •...
Page 305 HDMI display You can specify how movies are displayed as they are recorded via HDMI to an external device. Movie output itself is either 4K or Full HD, depending on the [Movie rec. size] setting. The default setting is [ •...
Page 306 For longer HDMI output To continue HDMI output for longer than 30 min., select [ ], then set [ : Auto power off] to [Disable] ( Caution HDMI output without information prevents display of warnings about the card space, battery level, or high internal temperature ( ) via HDMI.
Page 307: General Movie Recording Precautions
Image noise or irregular colors may occur when shooting at high ISO speeds, high temperatures, slow shutter speeds, or under low light. Movies are recorded essentially as they appear on the screen, except with Canon Log View Assist. Video and audio quality of recorded movies may be worse on other devices, and playback may not be possible, even if the devices support the camera's recording formats.
Page 308 If the card has a fast writing speed, the indicator will not appear or the level (if displayed) will not increase much. First, record a few test movies to see if the card can write fast enough. If the indicator shows that the card is full, and movie recording stops automatically, the sound near the end of the movie may not be recorded properly.
Page 309: Af/Drive
AF/Drive This chapter describes autofocus operation and drive modes and introduces menu settings on the [ : AF] tab. Caution < > stands for autofocus. < > stands for manual focus. • Tab Menus: AF Tab (Viewfinder Shooting) • Tab Menus: AF Tab (Live View Shooting) •...
Page 310: Tab Menus: Af Tab (Viewfinder Shooting)
Tab Menus: AF Tab (Viewfinder Shooting) Case 1 Case 2 Case 3 Case 4 Case A Tracking sensitivity Accel./decel. tracking AI Servo 1st image priority AI Servo 2nd image priority...
Page 311 Electronic full-time MF Lens electronic MF AF-assist beam firing One-Shot AF release prior. Subject tracking settings Lens drive when AF impossible Selectable AF point Select AF area selec. mode AF area selection method Orientation linked AF point Initial Servo AF pt,...
Page 312 AF point selection movement AF point display during focus AF point brightness AF status in viewfinder AF Microadjustment...
Page 313: Tab Menus: Af Tab (Live View Shooting)
Tab Menus: AF Tab (Live View Shooting) AF operation AF method Eye Detection AF Continuous AF MF peaking settings Focus guide...
Page 314 Case 1 Case 2 Case 3 Case 4 Case A Tracking sensitivity Accel./decel. tracking Electronic full-time MF Lens electronic MF One-Shot AF release prior.
Page 315 Subject tracking settings Lens drive when AF impossible Limit AF methods AF area selection method Orientation linked AF point Initial Servo AF pt,...
Page 316: Tab Menus: Af Tab (Movie Recording)
Tab Menus: AF Tab (Movie Recording) AF method Movie Servo AF Eye Detection AF MF peaking settings Focus guide...
Page 317 Movie Servo AF speed Movie Servo AF track sens. Electronic full-time MF Lens electronic MF Subject tracking settings Lens drive when AF impossible Limit AF methods AF area selection method...
Page 318: Af Operation
AF Operation One-Shot AF for Still Subjects AI Servo AF/Servo AF for Moving Subjects AF Status Indicator (Viewfinder Shooting) You can select the AF operation characteristics to suit the shooting conditions or subject. Set the lens's focus mode switch to < >.
Page 319 Select the AF operation. While looking at the top LCD panel or viewfinder, turn the < > dial. : One-Shot AF : AI Servo AF In Live View shooting, turn the < > dial. : One-Shot AF : Servo AF Note AF is also possible by pressing the <...
Page 320 One-Shot AF for Still Subjects This AF operation is suited for still subjects. When you press the shutter button halfway, the camera will focus only once. Viewfinder shooting • Once a subject is in focus, the focusing AF point (1) flashes in red, the focus indicator (2) <...
Page 321 AI Servo AF/Servo AF for Moving Subjects This AF operation is suited for moving subjects. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. Viewfinder shooting (AI Servo) • Once a subject is in focus, the focusing AF point is displayed. The focus indicator <...
Page 322 AF Status Indicator (Viewfinder Shooting) < > appears in the lower right of the viewfinder's field of view as the camera continues autofocusing while you press the shutter button halfway. In One-Shot AF mode, the icon also appears while you press the shutter button halfway after the camera has focused on a subject.
Page 323: Selecting The Af Area And Af Point (Viewfinder Shooting)
Selecting the AF Area and AF Point (Viewfinder Shooting) AF Area Selection Mode Selecting the AF Area Selection Mode Selecting the AF Point or Zone Manually Meaning of Lit or Blinking AF Points Registering AF Points The number of available AF points, the focusing patterns, and the Area AF frame shape vary by lens.
Page 324 1-point AF (manual selection) Select one AF point for focusing. AF point expansion (manual selection Focuses using your manually selected AF point < > and AF points outlined here in blue. AF point expansion (manual selection: surround) Focuses using your manually selected AF point < >...
Page 325 Zone AF (manual selection of zone) The AF area is divided into nine focusing zones for focusing. Large Zone AF (manual selection of zone) The AF area is divided into three focusing zones (left, center, and right) for focusing. Automatic selection AF The Area AF frame (entire AF area) is used to focus.
Page 326 Selecting the AF Area Selection Mode Press the < > button ( Press the < > button. Look through the viewfinder and press the < > button. Each time you press the < > button, the AF area selection mode changes.
Page 327 Selecting the AF Point or Zone Manually Press the < > button ( AF points are displayed in the viewfinder. With AF area expansion, surrounding AF points are also displayed. With Zone AF or Large Zone AF, your selected zone is displayed. Select an AF point or zone.
Page 328 Note Using these selection methods, you can manually select the initial AI Servo AF position when [ : Initial Servo AF pt, ] is set to [Initial AF pt set for Pressing the < > button displays following information on the top LCD panel. •...
Page 329 Meaning of Lit or Blinking AF Points Pressing the < > button lights up the AF points that are cross-type AF points for high- precision autofocusing. The blinking AF points are horizontal-line or vertical-line sensitive.
Page 330 Registering AF Points You can register the position of a frequently used AF point. For instant switching from the current AF point to your registered AF point, you can use a button you assign on advanced setting screens for [Metering and AF start], [Switch to registered AF point], [Direct AF point selection], or [Register/recall shooting func], in [ 6: Custom Controls] ( For instructions on registering AF points, see...
Page 331: Af Area Selection Modes (Viewfinder Shooting)
AF Area Selection Modes (Viewfinder Shooting) Spot AF (Manual Selection) 1-Point AF (Manual Selection) AF Point Expansion (Manual Selection AF Point Expansion (Manual Selection: Surround) Zone AF (Manual Selection of Zone) Large Zone AF (Manual Selection of Zone) Automatic Selection AF Shooting Conditions That Make Focusing Difficult Caution The camera continues to switch the active AF point <...
Page 332 Spot AF (Manual Selection) The camera focuses in a narrower area than 1-point AF. Select one AF point < > for focusing. Effective for pinpoint focusing or focusing on overlapping subjects such as an animal in a cage. Note that the small Spot AF area may make focusing difficult in handheld shooting or for moving subjects.
Page 333 1-Point AF (Manual Selection) Select one AF point < > for focusing.
Page 334 AF Point Expansion (Manual Selection Focuses using your manually selected AF point < > and surrounding AF points. Effective for moving subjects, which are difficult to track with 1-point AF. Although with AI Servo AF, the camera must be able to focus on your initially selected AF point <...
Page 335 AF Point Expansion (Manual Selection: Surround) Focuses using your manually selected AF point < > and surrounding AF points. Enables focusing over a wider area than AF point expansion (manual selection ). Effective for moving subjects, which are difficult to track with 1-point AF. AI Servo AF and One-Shot AF operation is the same as in AF point expansion (manual selection...
Page 336 Zone AF (Manual Selection of Zone) The AF area is divided into nine focusing zones for focusing. All AF points in your selected zone are used for automatic selection AF, which makes focusing easier than with 1-point AF or AF point expansion and effective for moving subjects. Focusing areas are determined not only based on the nearest subject but also based on a variety of other conditions such as faces, subject motion, or subject distance.
Page 337 Large Zone AF (Manual Selection of Zone) The AF area is divided into three focusing zones (left, center, and right) for focusing. Covers a larger area than Zone AF, using all AF points in your selected zone for automatic selection AF, which makes focusing easier than with 1-point AF or AF point expansion and effective for moving subjects.
Page 338 Automatic Selection AF The Area AF frame (entire AF area) is used to focus. AF points in focus are displayed with < >. With One-Shot AF, pressing the shutter button halfway displays the AF points < > that are focusing on the subject. Display of multiple AF points indicates that each point is in focus. Focusing areas are determined not only based on the nearest subject but also based on a variety of other conditions such as faces and subject distance.
Page 339 Shooting Conditions That Make Focusing Difficult Subjects with very low contrast. (Example: Blue skies, solid-color flat surfaces, etc.) Subjects in very low light. Strongly backlit or reflective subjects. (Example: Cars with highly reflective surfaces, etc.) Near and distant subjects positioned close to an AF point. (Example: Animals in cages, etc.) Light source such as dots of light positioned close to an AF point.
Page 340: Selecting The Af Method (Live View Shooting)
Selecting the AF Method (Live View Shooting) AF Method Selecting the AF Method (Face)+Tracking: Spot AF / 1-Point AF / AF Point Expansion ( ) / AF Point Expansion: Around / Zone AF / Large Zone AF: Vertical / Large Zone AF: Horizontal Magnified View AF Shooting Tips Shooting Conditions That Make Focusing Difficult...
Page 341 : Spot AF The camera focuses in a narrower area than 1-point AF. Effective for pinpoint focusing or focusing on overlapping subjects such as an animal in a cage. Note that the small Spot AF area may make focusing difficult in handheld shooting or for moving subjects.
Page 343 : Zone AF Uses auto selection AF in Zone AF frames to cover a larger area than AF point expansion, which makes focusing easier than with AF point expansion. Focusing areas are determined not only based on the nearest subject but also based on a variety of other conditions such as faces, subject motion, or subject distance.
Page 344 : Large Zone AF: Horizontal Uses auto selection AF in a horizontal Large Zone AF frame to cover a larger area than Zone AF, which makes focusing easier than with 1-point AF/AF point expansion and also effective for moving subjects. Focusing areas are determined not only based on the nearest subject but also based on a variety of other conditions such as faces, subject motion, or subject distance.
Page 345 Selecting the AF Method Press the < > button. Select the AF method. Each time you press the < > button, the AF method changes. Note You can also make your selection from [ : AF method]. The following descriptions apply to the camera with AF operation set to [One-Shot AF] ( ).
Page 346 (Face)+Tracking: The camera detects and focuses on people's faces. If a face moves, the AF point < > also moves to track the face. You can set [ : Eye Detection AF] to [Enable] to shoot with the subject's eyes in focus Check the AF point.
Page 347 Focus and take the picture. Once you press the shutter button halfway and the subject is in focus, the AF point turns green and the camera beeps. An orange Area AF frame indicates that the camera could not focus on subjects.
Page 348 AF point display After automatic face detection by the camera (single frame) After manual face selection (double frame) Note Selecting a face manually by tapping the screen or using < > locks onto that subject for tracking, and the camera tracks the subject even if it moves within the screen.
Page 349 Note The active < > may cover only a part of the face, not the whole face. The size of the AF point changes depending on the subject.
Page 350 Eye Detection AF With the AF method set to [ +Tracking], you can shoot with the subject's eyes in focus. Select [ : Eye Detection AF]. Select [Enable]. Aim the camera at the subject. An AF point is displayed around their eye. You can tap the screen to select an eye for focus.
Page 351 Take the picture. Caution Subject eyes may not be detected correctly, depending on the subject and shooting conditions. Note To switch to [Eye Detection AF: Disable] without using menu operations, press the < > button and then the < > button. To switch to [Eye Detection AF: Enable], press the <...
Page 352 Setting the initial Servo AF position You can manually set the initial Servo AF position when [ : Initial Servo AF pt, ] is set to [Initial AF pt set for Set the AF method to [ +Tracking] ( Set AF operation to [Servo AF] ( Set the AF point.
Page 353 Spot AF / 1-Point AF / AF Point Expansion ( ) / AF Point Expansion: Around / Zone AF / Large Zone AF: Vertical / Large Zone AF: Horizontal You can manually set the AF point or Zone AF frame. Here, 1-point AF screens are used as an example.
Page 354 Focus and take the picture. Aim the AF point over the subject and press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If the camera cannot focus, the AF point or Zone AF frame turns orange.
Page 355 Magnified View To check the focus when the AF method is other than [ +Tracking], magnify display by approx. 5× or 10× by pressing the < > button (or tapping < >). Magnification is centered on the AF point for [Spot AF], [1-point AF], [Expand AF area: ], and [Expand AF area: Around] and on the Zone AF frame for [Zone AF], [Large Zone AF: Vertical], and [Large Zone AF: Horizontal].
Page 356 AF Shooting Tips Even when focus is achieved, pressing the shutter button halfway will focus again. Image brightness may change during autofocusing. Depending on the subject and shooting conditions, it may take longer to focus, or the continuous shooting speed may decrease. If the light source changes as you shoot, the screen may flicker, and focusing may be difficult.
Page 357 Shooting Conditions That Make Focusing Difficult Subject with low-contrast such as the blue sky, solid-color flat surfaces or when highlight or shadow details are clipped. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Subjects with repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.).
Page 358 AF Range The available autofocus range varies depending on the lens used and settings such as recording size and Movie digital IS.
Page 359: Ai Servo Af/Servo Af Characteristics
AI Servo AF/Servo AF Characteristics Case Details Case 1: Versatile Multi-Purpose Setting Case 2: Continue to Track Subjects, Ignoring Possible Obstacles Case 3: Instantly Focus on Subjects Suddenly Entering AF Points Case 4: For Subjects That Accelerate or Decelerate Quickly Case A: Tracking Automatically Adapts to Subject Movement Parameters Adjusting Case Parameters...
Page 360 Select a case. Turn the < > dial to select a case icon, then press < >. Your selected case is now set. Selected cases are displayed in blue. Case Details Cases 1 to A are five combinations of settings for “Tracking sensitivity”...
Page 361 Case 1: Versatile Multi-Purpose Setting Default • Tracking sensitivity: 0 • Accel./decel. tracking: 0 Standard setting suited to moving subjects in general. Suitable for many kinds of subjects and scenes. In the following situations, select [Case 2] to [Case 4] instead: non-subjects moving across AF points, elusive subjects, or subjects that suddenly appear or change speed.
Page 362 Case 2: Continue to Track Subjects, Ignoring Possible Obstacles Default • Tracking sensitivity: Locked on: –1 • Accel./decel. tracking: 0 Setting to continue focusing on the subject even if non-subjects move across AF points, or if the subject strays from AF points. Effective if you prefer the focus not to switch to non- subjects or the background.
Page 363 Case 3: Instantly Focus on Subjects Suddenly Entering AF Points Default • Tracking sensitivity: Responsive: +1 • Accel./decel. tracking: +1 Setting to focus on a series of subjects at different distances in the AF points, one after another. Focus switches to any new subject that appears in front of the target subject. Also effective when you want to always focus on the closest subject.
Page 364 Case 4: For Subjects That Accelerate or Decelerate Quickly Default • Tracking sensitivity: Responsive: 0 • Accel./decel. tracking: +1 Setting to keep tracking and focusing on subjects even if they suddenly change speed. Effective for subjects having sudden movements, sudden acceleration/deceleration, or sudden stops.
Page 365 Case A: Tracking Automatically Adapts to Subject Movement Useful when you prefer to shoot with parameters set automatically, based on how subjects change. Tracking sensitivity and acceleration/deceleration tracking are set automatically.
Page 366 Parameters Tracking sensitivity Setting for AI Servo AF/Servo AF subject-tracking sensitivity in response to non-subjects moving across AF points or subjects straying from AF points. Standard setting. Suitable for moving subjects in general. Locked on: –2 / Locked on: –1 The camera will try to continue focusing on the subject even if non-subjects move across AF points or if the subject strays from the AF points.
Page 367 Accel./decel. tracking Setting for AI Servo AF/Servo AF subject-tracking sensitivity in response to sudden, significant changes in speed, as when subjects suddenly start or stop moving. Suited for subjects that move at a steady speed (minor changes in moving speed). –2 / –1 Suited for subjects that move at a steady speed (minor changes in moving speed).
Page 368 Adjusting Case Parameters You can manually adjust the parameters ((1) Tracking sensitivity and (2) Acceleration/ deceleration tracking) for cases 1 to 4. Select a case. Turn the < > dial to select the number of a case to adjust. Press the < >...
Page 369 Make the adjustment. Default settings are indicated by a light gray [ ] icon. To confirm the adjustment, press < >. To return to the screen in step 1, press the < > button. Note To restore default parameter settings for (1) and (2) to each case, press the <...
Page 370: Customizing Af Functions
Customizing AF Functions Viewfinder Shooting Other Menu Functions You can configure AF functions in detail to suit your shooting style or subject.
Page 371 Viewfinder Shooting AI Servo 1st image priority You can set the AF operation characteristics and shutter-release timing for the first shot with AI Servo AF. ] Equal priority Equal priority is given to focusing and shutter-release timing. [ ] Release Pressing the shutter button takes the picture immediately even if focus has not been achieved.
Page 372 AI Servo 2nd image priority With AI Servo AF for continuous shooting, you can preset the AF operation characteristics and shutter-release timing for the subsequent shots after the first shot in continuous shooting. [0] Equal priority Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, continuous shooting speed may slow down.
Page 373 Electronic full-time MF Operation of manual focus adjustment using the electronic focusing ring when certain lenses are attached is customizable. Check the Canon website for compatible lenses. Disable Operation of manual focus adjustment corresponds to the [Lens electronic MF] setting.
Page 374 ] One-Shot→enabled (magnify) You can manually adjust the focus after the AF operation if you keep holding down the shutter button halfway. You can magnify the area in focus and adjust the focus manually by turning the lens focusing ring in Live View shooting. ] Disable in AF mode Manual focus adjustment is disabled when the lens's focus mode switch is set to <...
Page 375 AF-assist beam firing You can enable or disable the AF-assist beam of a Speedlite for EOS cameras. ] Enable Enables firing of the AF-assist beam, when needed. ] Disable Disables firing of the AF-assist beam. Set if you prefer not to fire the AF-assist beam. ] IR AF assist beam only Enables infrared AF-assist beam firing by external Speedlites equipped with this feature, when these flash units are attached.
Page 376 One-Shot AF release prior. You can set the AF operation characteristics and shutter-release timing for One-Shot AF. ] Focus The picture will not be taken until focus is achieved. Useful when you want to achieve focus before capturing the image. [ ] Release Prioritizes shutter release over focus.
Page 377 Subject tracking settings You can specify conditions for automatic selection of the main subject to track, as well as ease of AF point switching to track other subjects. Applies to Zone AF/Large Zone AF/Auto selection AF area selection modes in viewfinder shooting, and to +Tracking/Zone AF/Large Zone AF (vertical or horizontal) AF methods in Live View shooting.
Page 378 Subject switching • Disable Tracks the subject initially determined for AF, to the extent possible. • Enable (slow) Generally tracks the subject initially determined for AF. May switch to other subjects if the current subject is no longer suitable for AF. •...
Page 379 Lens drive when AF impossible You can specify lens operation that applies when autofocusing on a subject is not possible. ] Continue focus search If focus cannot be achieved with autofocus, the lens is driven to search for the precise focus.
Page 380 Selectable AF point You can change the number of AF points available for manual selection. Note that regardless of the [Selectable AF point] setting, autofocusing for Zone AF, Large Zone AF, or Automatic selection AF uses the corresponding AF area selection mode. ] All points All AF points are available for manual selection.
Page 381 Select AF area selec. mode You can limit the selectable AF area selection modes to suit your shooting preferences. Select the desired AF area selection mode and press < > to add a checkmark [ ]. Select [OK] to register the setting. The AF area selection modes are described on AF Area Selection Modes (Viewfinder Shooting).
Page 382 AF area selection method You can set the method for switching AF area/AF method selection modes. →M-Fn button After you press the < > button, pressing the < > button will change the AF area/AF method selection mode. →Main Dial After you press the <...
Page 383 Orientation linked AF point You can set separate AF points to use in vertical and horizontal shooting, or you can set both separate AF points and separate AF area selection modes. ] Same for both vert/horiz The same AF area selection mode and manually selected AF point (or zone) are used in both vertical and horizontal shooting.
Page 384 Initial Servo AF pt, You can set the initial AF point for AI Servo AF/Servo AF when the AF area selection mode is set to [Auto selection AF], or when the AF method is set to [ +Tracking]. : Auto The initial AF point for AI Servo AF/Servo AF is set automatically to suit the shooting conditions.
Page 385 AF point selection movement When AF points are selected, you can set whether selection stops at the outermost AF point or continues to the first AF point on the opposite side. ] Stops at AF area edges Useful if you often use the outermost AF point. ] Continuous Instead of stopping at the outer edge, the selection of AF point continues to the opposite side.
Page 386 AF point display during focus You can set whether AF points are displayed throughout autofocusing: when AF begins and is in progress, when subjects are in focus, and after this, while the metering timer is active. ○: Displayed, ×: Not displayed AF point Before AF starts AF point display during focus...
Page 387 AF point brightness AF point brightness in the viewfinder is adjustable. AF status in viewfinder You can select whether to show the AF status indicator inside or outside of the viewfinder's field of view. ] Show in field of view <...
Page 388 Other Menu Functions Live View shooting These descriptions apply to menus only available in Live View Shooting. Continuous AF This function keeps subjects generally in focus. The camera is ready to focus immediately when you press the shutter button halfway. Note that fewer shots are available when set to [Enable], because the lens is driven continuously and battery power is consumed.
Page 389 Movie recording These descriptions apply to menus only available in movie recording. Movie Servo AF With this function enabled, the camera focuses on the subject continuously during movie recording. [Enable] • The camera focuses on the subject continuously even when you are not pressing the shutter button halfway.
Page 390 Caution When set to [Movie Servo AF: Enable] Shooting conditions that make focusing difficult • A fast-moving subject approaching or moving away from the camera. • A subject moving at a close distance to the camera. • When shooting with a higher aperture value. •...
Page 391 * Lenses supporting slow focus transition during movie recording USM and STM lenses released in and after 2009 are compatible. For details, refer to the Canon website. Caution With certain lenses, even if you adjust the AF speed, the speed may not change.
Page 392 Note Available when [ : Movie Servo AF] is set to [Enable] and [ : AF method] is set to [Spot AF] or [1-point AF]. Operation when [ : AF method] is set to an option other than [Spot AF] or [1- point AF] is equivalent to setting [AF speed] to [Standard(0)].
Page 393: Af Microadjustment
AF Microadjustment Adjusting for All Lenses by the Same Amount Adjusting for Individual Lenses Clearing All AF Microadjustments Fine adjustment of the point of focus is possible when autofocusing in viewfinder shooting. Before adjustment, also refer to Precautions for AF Microadjustment Notes for AF Microadjustment.
Page 394 Select [All by same amount]. Press the < > button. Make the adjustment. Set the adjustment amount. The adjustment range is ±20 steps. Setting it toward “–: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ”...
Page 395 Check the result of the adjustment. Take a picture and view it ( ) to check the results of adjustment. Adjust toward “+: ” to correct focusing in front of your targeted position, and adjust toward “–: ” to correct focusing behind it. Repeat the adjustment as necessary.
Page 396 Adjusting for Individual Lenses You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment is registered, the point of focus will always be shifted by the adjustment amount. Keep adjusting, shooting, and checking the results to set the adjustment amount manually.
Page 397 Check and change the lens information. (1) Registered number Displaying lens information Press the < > button. The lens name is displayed with a 10-digit serial number. When the serial number is displayed, select [OK] and go to step 4. “0000000000”...
Page 398 Lens serial numbers In step 3, if the asterisk “*” appears in front of the 10-digit lens serial number, you can register only one unit of the same lens model. Even if you enter the serial number, the asterisk “*” will remain displayed.
Page 399 Make the adjustment. Single focal length lens Zoom lens For a zoom lens, select the wide-angle (W) or telephoto (T) end. Pressing < > clears the purple frame and enables adjustment. Set the adjustment amount, then press < >. The adjustment range is ±20 steps.
Page 400 Select [Adjust by lens], then press < >. Check the result of the adjustment. Take a picture and view it ( ) to check the results of adjustment. Adjust toward “+: ” to correct focusing in front of your targeted position, and adjust toward “–: ”...
Page 401 Clearing All AF Microadjustments When [ Clear all] appears at the bottom of the screen, pressing the < > button will clear all the adjustments made for [All by same amount] and [Adjust by lens]. Caution Precautions for AF Microadjustment The AF's point of focus will vary slightly depending on the subject conditions, brightness, zoom position, and other shooting conditions.
Page 402: Manual Focus
Manual Focus Viewfinder Shooting Live View Shooting If focus cannot be achieved with autofocus, follow the procedure below to focus manually. Viewfinder Shooting Set the lens's focus mode switch to < >. Focus on the subject. Turn the lens focusing ring (1) until the subject looks sharp in the viewfinder.
Page 403 Live View Shooting You can magnify the image when focusing. Set the lens's focus mode switch to < >. Turn the lens focusing ring to set the approximate focus. Magnify the image. Each press of the < > button changes the magnification ratio, as follows.
Page 404 Move the magnified area. Use < > to move the magnified area into position for focusing. To return the magnified area to the center of the screen, press < > straight in or press the < > or < > button. Focus manually.
Page 405 Setting MF peaking (outline emphasis) In Live View shooting, edges of subjects in focus can be displayed in color to make focusing easier. You can set the outline color and adjust the sensitivity (level) of edge detection. Select [ : MF peaking settings]. Select [Peaking].
Page 406 If necessary, lower the ISO speed or set [Peaking] to [Off]. Note Peaking display shown on the screen is not recorded in images. MF peaking may be hard to discern when Canon Log is set. If necessary, set [View Assist.] to [On].
Page 407 Focus guide Setting [Focus guide] to [On] in Live View shooting provides a guide frame that shows which direction to adjust focus and the extent of adjustment needed. The guide frame is displayed near any eyes that are detected for the main subject when [ : AF method] is set to [ +Tracking] and [...
Page 408 The guide frame indicates the current position in focus and adjustment amount as follows. Significantly out of focus toward infinity Slightly out of focus toward infinity In focus Slightly out of focus toward close range Significantly out of focus toward close range...
Page 409 Adjustment information not detected Caution Under difficult shooting conditions for AF ( ), the guide frame may not be displayed correctly. No AF points are displayed while the guide frame is displayed. No adjustment information is detected for apertures darker than f/8 when MP-E 65mm f/2.8 1-5×...
Page 410: Selecting The Drive Mode
Selecting the Drive Mode Press the < > button ( Select the drive mode. While looking at the top LCD panel or viewfinder, turn the < > dial. ] Single shooting When you hold down the shutter button completely, only one shot will be taken. )] High-speed continuous shooting When you hold down the shutter button completely, you can shoot continuously at max.
Page 411 ] Low-speed continuous shooting When you hold down the shutter button completely, you can shoot continuously at max. approx. 3.0 shots/sec. while you keep holding it down. )] Single Soft shooting Enables slower mirror movement and shutter cocking in viewfinder shooting than in normal shooting.* No mechanical operation is performed until the shutter button returns to the halfway-pressed position.
Page 412 1/1000 sec. or faster shutter speed and maximum aperture (which varies by lens*) at room temperature (23°C/73°F) with flicker reduction disabled. * For details, refer to the Canon website. Using a Speedlite will decrease the maximum continuous shooting speed. Setting the drive mode to <...
Page 413: Using The Self-Timer
Using the Self-Timer Press the < > button ( Select the self-timer. While looking at the top LCD panel or viewfinder, turn the < > dial. : Shoot in 10 sec. : Shoot in 2 sec.
Page 414 Take the picture. Look through the viewfinder, focus, then press the shutter button completely. You can check self-timer operation by watching the blinking of the self- timer lamp and the countdown display (in seconds) on the top LCD panel. The self-timer lamp blinks faster approx. 2 sec. before the shot. Caution If you will not look through the viewfinder when pressing the shutter button, close the eyepiece shutter before shooting (...
Page 415: Playback
Playback This chapter covers topics related to playback—playing back captured still photos and movies—and introduces menu settings on the Playback ([ ]) tab. Caution Normal display or selection on this camera may not be possible for images captured on other cameras, or images from this camera that have been edited or renamed on a computer.
Page 416 • Displaying the Highlight Alert • AF Point Display • Playback Grid • HDMI HDR Output...
Page 417: Tab Menus: Playback
Tab Menus: Playback Playback 1 Protect images Rotate image Erase images Print order Image copy HEIF→JPEG conversion Playback 2 RAW image processing Cropping Resize Rating Slide show Set image search conditions Image jump w/...
Page 418 Playback 3 Playback information display Highlight alert AF point disp. Playback grid Movie play count Magnificatn (apx) HDMI HDR output...
Page 419: Image Playback
Image Playback Single-Image Display Shooting Information Display Touch Playback Single-Image Display Switch to playback. Press the < > button. The last image captured or played back is displayed. Browse images. To play back images starting with your most recent shot, turn the <...
Page 420 No information Basic information display Shooting information display Caution When played back, images captured with [ 7: Add cropping information] set to an option other than [Off (aspect ratio 3:2)] ) are displayed with lines indicating the image area. Exit image playback. Press the <...
Page 421 Shooting Information Display With the shooting information screen displayed ( ), you can press < > up or down to view other information. You can also customize the information displayed, in [ : Playback information display] (...
Page 422 Touch Playback The camera features a touch-screen panel that you can touch to control playback. Supported touch operations are like those used with smartphones and similar devices. First, press the < > button to prepare for touch playback. Browse images Jump display Index display...
Page 423 Magnified view Note You can also magnify display by double-tapping with one finger.
Page 424: Magnified Image Display
Magnified Image Display Setting the Initial Magnification Ratio and Position You can magnify captured images by approx. 1.5× to 10×. Magnify the image. Magnification is possible at these times: 1. During image playback (single-image display), 2. During image review after shooting, and 3. When the camera is ready to shoot.
Page 425 Scroll the image. Use < > to scroll around the magnified image. With the Smart controller, you can also move the magnified area itself. Press the < > or < > button to exit magnified view. Note To switch to other images while maintaining magnified view, turn the < >...
Page 426 Setting the Initial Magnification Ratio and Position You can set the initial magnification ratio and magnified position by selecting [ Magnificatn (apx)]. 1x (no magnification) The image is not magnified. The magnified view will start with the single-image display. 2x, 4x, 8x, 10x (magnify from center) The magnified view starts at the image center at the selected magnification ratio.
Page 427: Index Display (Multiple-Image Display)
Index Display (Multiple-Image Display) Press the < > button. During image playback, press the < > button. ] will be displayed in the lower right of the screen. Switch to the index display. Turn the < > dial counterclockwise. The 4-image index display will appear. The selected image is highlighted with an orange frame.
Page 429 Browse images. Use < > or the < > dial to move the orange frame for image selection. To display images on the next or previous screen, press the < > button to clear the [ ] icon, then turn the < >...
Page 430: Voice Memo Recording And Playback
Voice Memo Recording and Playback Recording Voice Memos Playing Voice Memos You can add (record) voice memos to your shots. Voice memos are recorded as WAV audio files with the same file number as the image. They can be played back by the camera or a computer.
Page 431 Record a voice memo. Hold down the < > button for approx. 2 sec. Keep holding down the button after [Recording memo...] appears, and speak into the voice memo microphone (1). Each recording can be up to approx. 30 sec. To end the voice memo, release the button.
Page 432 Note Audio quality of voice memo recording can be changed in [ 7: Memo audio quality]. To record voice memos longer than 30 sec., repeat step 2. You can record a single voice memo during image review (immediately after shooting) by following step 2. Even during transfer to an FTP server, you can add a voice memo to images from the playback screen.
Page 433 Playing Voice Memos Select [ / button function]. Select [Play memo(Hold:Rec. memo)]. Select an image for voice memo playback. Press the < > button to switch to image playback. Turn the < > dial to select an image labeled with a [ ] icon at the top of the screen.
Page 434 Play back the voice memo. (1) Speaker Press the < > button to play back the voice memo. You can adjust the sound volume by turning the < > dial. Press the < > button to stop playback. Note Multiple voice memos added to an image are played back consecutively. Added voice memos cannot be erased by themselves using the camera.
Page 435: Movie Playback
Movie Playback Switch to playback. Press the < > button. Select a movie. Turn the < > dial to select a movie to play. In single-image display, the < > icon displayed in the upper left of the screen indicates a movie. In index display, perforations at the left edge of a thumbnail indicate a movie.
Page 436 In the single-image display, tap < > or press < >. Press < > to play back the movie. (1) Speaker The movie will start playing back. You can pause playback and display the movie playback panel by pressing < >.
Page 437 Movie playback panel Item Playback Operations Playback Pressing < > toggles between playback and stop. Adjust the slow motion speed by turning the < > dial. The slow Slow motion motion speed is indicated in the upper right of the screen. Skip backward Skips backward approx.
Page 438: Editing A Movie's First And Last Scenes
Editing a Movie's First and Last Scenes You can edit out the first and last scenes of a movie in approx. 1-sec. increments. In single-image display, press < >. On the movie playback panel, select [...
Page 439 Specify the part to be edited out. Select either [ ] (Cut beginning) or [ ] (Cut end). Press < > left or right to go back or forward one frame. Keep pressing the multi-controller to fast rewind or fast forward frames. Each turn of the <...
Page 440 Save the image. Select [ ] (1). The save screen will appear. To save it as a new file, select [New file], or to save it and overwrite the original movie file, select [Overwrite]. On the confirmation screen, select [OK] to save the edited movie and return to the movie playback screen.
Page 441: 4K Movie Frame Grab
4K Movie Frame Grab From 4K movies, you can select individual frames to save as JPEG still images. This function is called “Frame Grab (4K frame capture)”. Select a 4K movie. Turn the < > dial to select a 4K quality movie. On the shooting information screen ( ), 4K movies are labeled with ], [...
Page 442 Frame grabbing is not possible from the following 4K movies. • RAW movies • Movies recorded with [ : Canon Log settings] set to [On] • Movies recorded with other cameras Frame grabbing is not possible while the camera is connected to a computer.
Page 443: Playback On A Tv Set
Playback on a TV Set By connecting the camera to a television with an HDMI cable, you can play back the captured still photos and movies on the television. Using the HDMI Cable HTC-100 (sold separately) is recommended. If the image does not appear on the TV screen, confirm that [ : Video system] is correctly set to [For NTSC] or [For PAL] (depending on the video system of your television).
Page 444 Press the < > button. Images are now displayed on the television, with nothing displayed on the camera screen. The images will automatically be displayed at the optimum resolution matching the connected television. Caution Adjust movie sound volume with the television. The sound volume cannot be adjusted with the camera.
Page 445: Protecting Images
Protecting Images Protecting Individual Images with the < > Button Protecting Individual Images via the Menu Specifying the Range of Images to Protect Protecting All Images in a Folder or on a Card You can protect important images from being accidentally erased. Caution If you format the card ( ), the protected images will also be erased.
Page 446 Protect the image. Press the < > button to protect the image, after which it will be labeled with a < > icon (1) at the top of the screen. To cancel protection and clear the < > icon, press the < >...
Page 447 Protecting Individual Images via the Menu Select [ : Protect images]. Select [Select images]. Select the image to protect. Turn the < > dial to select an image to protect.
Page 448 Protect the image. Press < > to protect the selected image, after which it will be labeled with a < > icon (1) at the top of the screen. To cancel protection and clear the < > icon, press < >...
Page 449 Specifying the Range of Images to Protect While looking at the images in the index display, you can specify the first and last images for a range to protect all the specified images at once. Select [Select range]. Specify the range of images. Select the first image (start point).
Page 450 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at once. When you select [All images in folder] or [All images on card] in [ : Protect images], all the images in the folder or on the card will be protected.
Page 451: Rotating Images
Rotating Images You can use this feature to rotate the displayed image to the desired orientation. Select [ : Rotate image]. Select an image to rotate. Turn the < > dial to select the image. Rotate the image. Each time you press < >, the image will rotate clockwise as follows: 90°→270°→0°.
Page 452 Note If you set [ : Auto rotate] to [On ) before taking pictures, you need not rotate the image with this function. If the rotated image is not displayed in the rotated orientation during image playback, set [ : Auto rotate] to [On Movies cannot be rotated.
Page 453: Erasing Images
Erasing Images Erasing Images Individually Selecting ([ ]) Multiple Images to Erase Together Specifying the Range of Images to Erase Erasing All Images in a Folder or on a Card You can either select and erase unnecessary images individually or erase them in one batch.
Page 454 Erase the images. JPEG/HEIF/RAW images or movies Select [Erase]. RAW+JPEG/RAW+HEIF images Select an item.
Page 455 Selecting ([ ]) Multiple Images to Erase Together By adding checkmarks to the images to be erased, you can erase all those images at once. Select [ : Erase images]. Select [Select and erase images]. Select an image. Turn the < >...
Page 456 Erase the images. Press the < > button, then press [OK].
Page 457 Specifying the Range of Images to Erase While looking at the images in the index display, you can specify the first and last images for a range to erase all the specified images at once. Select [Select range]. Specify the range of images. Select the first image (start point).
Page 458 Erase the images. Select [OK].
Page 459 Erasing All Images in a Folder or on a Card You can erase all the images in a folder or on a card at once. When you select [All images in folder] or [All images on card] in [ : Erase images], all the images in the folder or on the card will be erased.
Page 460: Print Ordering (Dpof)
Print Ordering (DPOF) Setting Print Options Selecting Images for Printing DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing instructions such as the image selection, quantity to print, etc. You can print multiple images in one batch or create a print order for a photofinisher. You can set the print settings such as print type, date imprinting, file number imprinting, etc.
Page 461 Set the options as desired. Set [Print type], [Date], and [File No.] options. Standard Prints one image on one sheet. Multiple thumbnail images are printed Index Print type on one sheet. Prints both the standard and index Both prints. [On] imprints the recorded date of the captured Date image.
Page 462 Caution If you print an image with a large image size using the [Index] or [Both] setting ), the index print may not be printed with certain printers. In this case, resize the image ( ), then print the index print. Even if [Date] and [File No.] are set to [On], the date or file number may not be imprinted, depending on the print type setting and printer.
Page 463 Selecting Images for Printing Sel.Image Select and specify the images individually. Press the < > button to save the print order to the card. Standard/Both (1) Quantity (2) Total images selected Press < > to print a copy of the displayed image. By turning the < >...
Page 464 Multiple Select range Select [Select range] in [Multiple]. Selecting the first and last images of the range marks all the images in the range with a checkmark [ ], and one copy of each image will be specified for printing. All images in a folder Select [Mark all in folder] and select the folder.
Page 465 Caution RAW images or movies cannot be specified for printing. Note that RAW images or movies will not be specified for printing even if you specify all images with [Multiple]. When using a PictBridge-compatible printer, do not specify more than 400 images for one print order.
Page 466: Copying Images
Copying Images Copying Individual Images Copying a Range of Images Copying All Images in a Folder or on a Card You can copy the images on one card to the other card to save duplicates. All images in a folder or on a card can also be copied at the same time. Caution If the target folder or card already has an image with the same file number, [Skip image and continue], [Replace existing image], and [Cancel copy] are...
Page 467 Copying Individual Images Select [ : Image copy]. Select [Sel.Image]. Check the source and target card numbers and the free space on the target card. Select [Sel.Image], then press < >.
Page 468 Select the folder. (1) Number of images in folder (2) Lowest file number (3) Folder name (4) Highest file number Select the source folder, then press < >. When selecting the folder, refer to the images displayed at right of the screen.
Page 469 Press the < > button. After selecting all images to copy, press the < > button. Select [OK]. Check the target card, then select [OK]. Select the target folder. Select the folder to copy the image to, then press < >.
Page 470 Select [OK]. Check the information about the source and target card, then select [OK]. Results are displayed after copying is finished. Select [OK] to return to the screen in step 2.
Page 471 Copying a Range of Images You can copy all specified images at once by selecting the first and last images in a range as you look at images in the index display. Select [Range]. Select the folder. Select the source folder, then press < >.
Page 472 Specify the range of images. Select the first image (start point). Next, select the last image (end point). A checkmark [ ] will be appended to all the images within the range between first and last images. To select another image to copy, repeat step 3.
Page 473 Copying All Images in a Folder or on a Card You can copy all the images in a folder or on a card at once. Selecting [Sel. ] or [All images] in [ : Image copy] copies all the images it contains.
Page 474: Converting Heif To Jpeg
Converting HEIF to JPEG You can convert HEIF images captured in HDR shooting and save them as JPEG images. Converted JPEGs resemble how the original HEIF image appears on an HDR display device. Select [ : HEIF→JPEG conversion]. Select an image. Turn the <...
Page 475 Save the image. Select [OK] to save the JPEG image. • Check the destination folder and image file number, then select [OK]. • To convert another image, repeat steps 2 and 3. Note Some scenes may look different after conversion if the original and converted images are compared.
Page 476: Raw Image Processing
RAW Image Processing Magnified View RAW Image Processing Options You can process images with the camera to create JPEG or HEIF images. RAW images are not affected, so different conditions can be applied to create JPEG or HEIF images. You can also use Digital Photo Professional (EOS software) to process RAW images. Caution Processing into HEIF is not available for images captured with...
Page 477 Select an item, then select images. You can select multiple images to process at once. Selecting images Turn the < > dial to select images to process, then press < >. Press the < > button. Selecting range Select the first image (start point). Next, select the last image (end point).
Page 478 Set the desired processing conditions. Use shot settings Images are processed using image settings at the time of capture. RAW images captured in HDR shooting are processed to create HEIF images, and other RAW images are processed to create JPEGs. Set up processing→JPEG/Set up processing→HEIF Turn the <...
Page 479 Save the image. When using [Set up processing→JPEG] or [Set up processing→ HEIF], select [ ] (Save). Read the message and select [OK]. To process other images, select [Yes] and repeat steps 2–4. Select the image to display. Select [Original image] or [Processed img.].
Page 480 Magnified View You can magnify images displayed for [Set up processing→JPEG] or [Set up processing →HEIF] by pressing the < > button. The magnification ratio varies depending on the [Image quality] setting. With < >, you can scroll around the magnified image. To cancel the magnified view, press the <...
Page 481 RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. White balance ( You can select the white balance. Selecting [ ] enables you to select [Auto: Ambience priority] or [Auto: White priority]. If you select [ ], you can set the color temperature.
Page 482 Lens aberr correction • Peripheral illum corr ( A phenomenon that makes the image corners look darker due to the lens characteristics can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, magnify the image ( ) and check the four corners.
Page 483 Caution Processing RAW images in the camera will not produce exactly the same results as processing RAW images with Digital Photo Professional (EOS software). If you perform [Brightness adjustment], noise, banding, etc. may be intensified with the effects of adjustment. When [Digital Lens Optimizer] is set, noise may be intensified together with the effects of correction.
Page 484: Cropping Jpeg Images
Cropping JPEG Images You can crop a captured JPEG image and save it as another image. Cropping an image is possible only with JPEG images. Cropping is not available for HEIF or RAW images, or for frame-grab images from 4K movies. Select [ : Cropping].
Page 485 Set the cropping frame. The image area within the cropping frame will be cropped. Resizing the cropping frame size Turn the < > dial to resize the cropping frame size. The smaller the cropping frame, the more magnified the cropped image will look. Changing the cropping frame aspect ratio and orientation Turn the <...
Page 486 Save the image. Press < > and select [OK] to save the cropped image. Check the destination folder and image file number, then select [OK]. To crop another image, repeat steps 2 to 5. Caution The position and size of the cropping frame may change depending on the angle set for tilt correction.
Page 487: Resizing Jpeg Images
Resizing JPEG Images You can resize a JPEG image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG / images. Resizing is not available for JPEG , HEIF, or RAW images, or for frame-grab images from 4K movies. Select [ : Resize].
Page 488 Select the desired image size. Press < > to display the image sizes. Select the desired image size (1). Save the image. Select [OK] to save the resized image. Check the destination folder and image file number, then select [OK]. To resize another image, repeat steps 2 to 4.
Page 489: Rating Images
Rating Images Rating Individual Images Rating by Specifying the Range Rating All Images in a Folder or on a Card You can rate images on a scale of 1–5 ( ). This function is called rating. * Rating images can help you organize them. Rating Individual Images Select [ : Rating].
Page 490 Select the image to be rated. Turn the < > dial to select the image to be rated. Rate the image. Press < >, and a blue highlight frame will appear as shown in the screen shown above. Turn the < >...
Page 491 Rating by Specifying the Range While looking at the images in the index display, you can specify the first and last images for a range to rate all the specified images at once. Select [Select range]. Specify the range of images. Select the first image (start point).
Page 492 Rate the images. Turn the < > dial to select a rating mark, then select [OK]. All the images in the specified range will be rated (same rating) at once.
Page 493 Rating All Images in a Folder or on a Card You can rate all the images in a folder or on a card at once. Under [ : Rating], when you select [All images in folder] or [All images on card], all the images in the folder or on the card will be rated.
Page 494 Note Values next to ratings are displayed as [###] if more than 1,000 images have that rating. With [ : Set image search conditions] and [ : Image jump w/ ], you can display only the images given a specific rating.
Page 495: Slide Show
Slide Show You can play back the images on the card as an automatic slide show. Specify the images to be played back. To play back all the images on the card, go to step 2. If you want to specify the images to be played back in the slide show, filter the images with [ : Set image search conditions] ( Select [...
Page 496 Set the playback as desired. Select [Set up]. Set the [Display time] and [Repeat] (repeated playback) settings for the still photos. After completing the settings, press the < > button. Display time Repeat...
Page 497 Start the slide show. Select [Start]. After [Loading image...] is displayed, the slide show will start. Exit the slide show. To exit the slide show and return to the setting screen, press the < > button. Note To pause the slide show, press < >.
Page 498: Setting Image Search Conditions
Setting Image Search Conditions Clearing the Search Conditions You can filter image display according to your search conditions. After setting the image search conditions, you can play back and display only the found images. You can also protect, rate, play a slide show, erase, and apply other operations to filtered images. Select [ : Set image search conditions].
Page 499 Set the search conditions. Turn the < > dial to select an item. Turn the < > dial to set the option. A checkmark [ ] (1) is appended to the left of the item. (Specified as the search condition.) If you select the item and press the <...
Page 500 Apply the search conditions. Press < > and read the message displayed. Select [OK]. The search condition is applied. Display the found images. Press the < > button. Only the images that match the set conditions (filtered) will be played back.
Page 501 Note Search conditions may be cleared after operations involving camera power or card changes and editing, adding, or erasing images. Auto power off time may be extended while the [ : Set image search conditions] screen is displayed. Clearing the Search Conditions Access the screen in step 2, then press the <...
Page 502: Browsing Images With The Main Dial
Browsing Images with the Main Dial In single-image display, you can turn the < > dial to jump through the images forward or backward according to the jump method set. Select [ : Image jump w/ Select the jump method. Note With [Jump images by the specified number], you can turn the <...
Page 503 Browse by jumping. (1) Jump method (2) Playback position Press the < > button. In single-image display, turn the < > dial. You can browse by the jump method set.
Page 504: Customizing Playback Information Display
Customizing Playback Information Display Histogram You can specify screens and accompanying information displayed during image playback. Select [ : Playback information display].
Page 505 Add a checkmark [ ] next to the number of screens to display. Select numbers with the < > dial. Press < > to add a checkmark [ ]. Repeat these steps to add a checkmark [ ] to the number of each screen to display, then select [OK].
Page 506 [Brightness] display This histogram is a graph showing the distribution of the image's brightness level, with the horizontal axis indicating the brightness level (darker on the left and brighter on the right) and the vertical axis indicating the pixel count at each brightness level. The more pixels there are toward the left, the darker the image, and the more pixels there are toward the right, the brighter the image.
Page 507 [RGB] display This histogram is a graph showing the distribution of each primary color's brightness level in the image (RGB or red, green, and blue), with the horizontal axis indicating the color's brightness level (darker on the left and brighter on the right) and the vertical axis indicating the pixel count at each color brightness level.
Page 508: Displaying The Highlight Alert
Displaying the Highlight Alert You can specify blinking display of overexposed highlights on the playback screen. To obtain more detailed gradation in the blinking areas where you want the gradation to be faithfully reproduced, set the exposure compensation to a negative amount and shoot again for a better result.
Page 509: Af Point Display
AF Point Display You can display the AF points that were used to focus, which will be outlined in red on the playback screen. If automatic AF point selection is set, multiple AF points may be displayed. Select [ : AF point disp.]. Select [Enable].
Page 510: Playback Grid
Playback Grid You can display a grid over still photos shown in single-image display on the playback screen. This function is convenient for checking the image's vertical or horizontal tilt as well as composition. Select [ : Playback grid]. Select an item.
Page 511: Hdmi Hdr Output
HDMI HDR Output You can view RAW or HEIF images in HDR by connecting the camera to an HDR TV. Select [ : HDMI HDR output]. Select [On]. Caution HDR display in HDMI output is not available for RAW images captured with [HDR PQ settings] set to [Disable].
Page 512: Communication Functions
Caution Important Note that Canon cannot be held liable for any loss or damage caused by erroneous network settings when using the camera. In addition, Canon cannot be held liable for any other loss or damage caused by use of the camera.
Page 513: Tab Menus: Communication Functions Tab
Tab Menus: Communication Functions Tab Network settings Bluetooth settings Nickname GPS settings Image transfer Reset communication settings Caution Wi-Fi connections are not possible while the camera is connected to a computer or other device via an interface cable. Other devices, such as computers, cannot be used with the camera by connecting them with an interface cable while the camera is connected to devices via Wi-Fi.
Page 514: Available Communication Functions
FTP transfer settings. Syncing time between cameras ( The time on multiple EOS-1D X Mark III cameras can be synchronized over a wired LAN connection. Wireless File Transmitter By attaching an optional Wireless File Transmitter WFT-E9, you can use wireless LAN features.
Page 515 Available communication functions and connection methods (besides GPS) Connection Method Wireless LAN Available Features Wired Wi-Fi (Wireless File (Built-In) Transmitter WFT-E9) Camera Connect communication from ○ smartphones Using EOS Utility ○ ○ ○ Image transfer to FTP servers ○ ○ ○...
Page 516: Camera Connect Communication From Smartphones
Camera Connect Communication from Smartphones Connecting to a Bluetooth-compatible Smartphone via Wi-Fi Camera Connect Functions Canceling the Pairing Wi-Fi Connection Without Using Bluetooth Automatic Image Transfer as You Shoot Sending Images to a Smartphone from the Camera Settings to Make Images Viewable from Smartphones General Precautions on Camera Connect Communication from Smartphones By using the dedicated Camera Connect app installed on a smartphone or tablet (collectively referred to hereafter as “smartphones”), you can pair the camera and...
Page 517 Note You can also access Google Play or App Store from QR codes displayed when you pair the smartphone and camera. For the operating system versions supported by Camera Connect, refer to the download site of Camera Connect. Sample screens and other details in this guide may not match the actual user interface elements after camera firmware updates or updates to Camera Connect, Android, or iOS.
Page 518 Select [ : Network settings]. Select [Enable]. Select [Bluetooth settings].
Page 519 Set [Bluetooth] to [Enable]. Select [Pairing]. Select an option. If Camera Connect is already installed, select [Do not display]. If Camera Connect is not installed, select [Android] or [iOS], scan the displayed QR code with the smartphone to access Google Play or App Store and install Camera Connect.
Page 520 Steps on the smartphone (2) Start Camera Connect. Tap the camera for pairing. If you are using an Android smartphone, go to step 11. Tap [Pair] (iOS only).
Page 521 Steps on the camera (2) Select [OK]. Press the < > button. Pairing is now complete, and the camera is connected to the smartphone via Bluetooth. A Bluetooth icon appears on the main Camera Connect screen. Caution Bluetooth connection consumes battery power even after the camera's auto power off is activated.
Page 522 Note When paired via Bluetooth, tap [Bluetooth remote controller] in Camera Connect to control the camera remotely from the smartphone. From an Android device, you can control the camera to send images to the smartphone (...
Page 523 Steps on the smartphone (3) Tap a Camera Connect function. In iOS, tap [Join] when a message is displayed to confirm camera connection. After the devices are connected via Wi-Fi, a screen for the selected function is displayed on the smartphone. The Bluetooth and Wi-Fi icons are now displayed on the main Camera Connect screen, after you return to that screen.
Page 524 Camera Connect Functions Images on camera Images can be browsed, deleted, or rated. Images can be saved on a smartphone. Remote live view shooting Enables remote shooting as you view a live image on the smartphone. Auto transfer Enables camera and app setting adjustment for automatic transfer of your shots ( Bluetooth remote controller Enables remote control of the camera from a smartphone paired via Bluetooth.
Page 525 Canceling the Pairing Cancel pairing with a smartphone as follows. Select [Check/clear connection info]. Press the < > button. Select [OK]. Clear the camera information on the smartphone. In the smartphone's Bluetooth setting menu, clear the camera information registered on the smartphone.
Page 526 Note To check the camera's Bluetooth address, select [Bluetooth address].
Page 527 Wi-Fi Connection Without Using Bluetooth These instructions describe how to establish a direct Wi-Fi connection with a smartphone and use Camera Connect to control the camera. Steps on the camera (1) On the camera, press the < > button. Select [ : Network settings].
Page 528 Select [SET* Unspecified]. Select [Create with wizard]. Select [Configure online]. Select [OK].
Page 529 Select [Smartphone]. Select [OK]. Press the < > button. Select [OK]. Select [New settings]. Select [OK].
Page 530 Select [Camera access point mode]. Select [Easy connection]. Select [OK]. Select [OK].
Page 531 Press the < > button. Select [New settings]. Select [OK]. Check the SSID (network name) and password. Check the SSID (1) and password (2) displayed on the camera screen.
Page 532 Steps on the smartphone Operate the smartphone to establish a Wi-Fi connection. Activate the smartphone's Wi-Fi function, then tap the SSID (network name) you checked in step 16. In the password field, enter the password you checked in step 16, then tap [Join].
Page 533 Steps on the camera (2) Select [OK]. To specify viewable images, press the < > button. For details on conditions that enable image viewing, see Settings to Make Images Viewable from Smartphones. Press < >.
Page 534 Press < >. The main window of Camera Connect will be displayed on the smartphone. The camera's < > lamp is lit in green. The Wi-Fi connection to a smartphone is now complete. Operate the camera using Camera Connect ( When connected via Wi-Fi, you can send images to a smartphone from the Quick Control screen during playback ( Terminating Wi-Fi connections (...
Page 535 Automatic Image Transfer as You Shoot Your shots can be automatically sent to a smartphone. Before following these steps, make sure the camera and smartphone are connected via Wi-Fi. Select [ : Network settings]. Select [Connection option settings]. Select [Smartphone settings].
Page 536 Set [Auto send] to [Enable]. If necessary, specify [Size to send].
Page 537 Sending Images to a Smartphone from the Camera You can use the camera to send images to a smartphone paired via Bluetooth (Android devices only) or connected via Wi-Fi. Switch to playback. Press the < > button. Select [ Send images to smartphone]. If you perform this step while connected via Bluetooth, a message is displayed, and the connection switches to a Wi-Fi connection.
Page 538 Sending images individually Select an image to send. Turn the < > dial to select an image to send, then press < >. You can press the < > button and turn the < > dial counterclockwise to select the image using the index display. Select [Send img shown].
Page 539 Select [Send selected]. Select images to send. Turn the < > dial to select images to send, then press < >. To switch to three-image display for image selection, press the < > button and turn the < > dial counterclockwise. To return to the single-image display, press the <...
Page 540 Select [Size to send]. On the displayed screen, select an image size. Select [Send].
Page 541 Sending a specified range of images Press < >. Select [Send range]. Specify the range of images. Select the first image (start point). Select the last image (end point). To cancel the selection, repeat this step. To change the number of images in index display, press the < >...
Page 542 Confirm the range. Press the < > button. Select [Size to send]. On the displayed screen, select an image size. Select [Send].
Page 543 Sending all images on the card Press < >. Select [Send all card]. Select [Size to send]. On the displayed screen, select an image size.
Page 544 Select [Send]. Sending images that match the search conditions Send all the images that match the search conditions set in [Set image search conditions] at once. For details on [Set image search conditions], see Setting Image Search Conditions. Press < >.
Page 545 Select [Size to send]. On the displayed screen, select an image size. Select [Send]. Ending image transfer ( Caution During the image transfer operation, a picture cannot be taken even if the camera's shutter button is pressed.
Page 546 Note You can cancel the image transfer by selecting [Cancel] during the transfer. You can select up to 999 files at a time. With a Wi-Fi connection established, disabling the smartphone's power saving function is recommended. Selecting the reduced size for still photos applies to all still photos sent at that time. Note that size still photos are not reduced.
Page 547 Settings to Make Images Viewable from Smartphones Images can be specified after the Wi-Fi connection is terminated. Select [Network settings]. Select [Manual setting]. Select [Function settings].
Page 548 Select [Smartphone]. Select [Change]. Select [Viewable imgs].
Page 549 Select an option. Select [OK] to access the setting screen. [All images] All images stored on the card become viewable. [Images from past days] Specify viewable images on the shooting-date basis. Images shot up to nine days ago can be specified. When [Images shot in past days] is selected, images shot up to the specified number of days before the current date become viewable.
Page 550 [Select by rating] Specify viewable images depending on whether a rating is appended (or not appended) or by the type of rating. Once you select the type of rating, the viewable images are set. [File number range] (Select range) Select the first and last images from images arranged by the file number to specify the viewable images.
Page 551 General Precautions on Camera Connect Communication from Smartphones Caution If the Wi-Fi connection is terminated while recording a movie with remote shooting, the following will occur. • If the Live View shooting/Movie shooting switch is set to < >, movie recording will continue.
Page 552: Wi-Fi Connections With A Computer Using Eos Utility
Wi-Fi Connections with a Computer Using EOS Utility Connecting to a Computer via Wi-Fi Using EOS Utility, you can browse images on the camera and save them to the computer. Also in EOS Utility, you can shoot by controlling the camera remotely and change camera settings.
Page 553 Select [Enable]. Select [Connection settings]. Select [SET* Unspecified].
Page 554 Select [Create with wizard]. Select [Configure online]. Select [OK]. Select [EOS Utility]. Select [OK].
Page 555 Select [Wi-Fi]. Select [OK]. Select [New settings]. Select [OK]. Select [Connect with WPS].
Page 556 Select [WPS (PBC mode)]. Select [OK]. Steps on the access point Connect to the access point via Wi-Fi. Press the access point's WPS button. Steps on the camera (2) Select [OK].
Page 557 Select [Auto setting]. Select [OK]. Select [Disable]. Select [OK]. Press < >.
Page 558 Select [New settings]. Select [OK]. For details on subsequent operations, see Configuring EOS Utility Connection Settings. Terminating Wi-Fi connections ( Reconnecting (...
Page 559: Basic Communication Settings
Basic Communication Settings Preparation Displaying the Connection Wizard Checking the Type of Access Point Connecting via WPS (PBC Mode) Connecting via WPS (PIN Mode) Connecting Manually to Detected Networks Connecting Manually by Specifying Networks Connecting in Infrastructure Mode Connecting in Camera Access Point Mode Setting the IP Address Configuring Communication Function Settings Before using the following camera communication functions, configure camera and...
Page 560 • Windows 7 Home Premium [EOS Utility] A computer with EOS Utility (EOS software) installed is required. For EOS Utility installation instructions, visit the Canon website. [Browser Remote] Use of [Browser Remote] requires a computer with one of the following browsers installed.
Page 561 When connecting via Wi-Fi Connect the computer for the Wi-Fi connection to the access point in advance. Caution Transferring movies Each movie file is large, and transferring large files over Wi-Fi may take some time. Referring to Communication Function Precautions, arrange your network environment for stable communication between devices and the access point.
Page 562 Displaying the Connection Wizard This section describes the process of following the connection wizard instructions to add connection settings. If an error is displayed, see Troubleshooting and check the settings. Be careful not to press the shutter button or other controls (which will close the connection wizard) until configuration is complete.
Page 563 Select [Connection settings]. Select [SET*]. Select [Create with wizard]. Selecting [Create from list] when multiple communication and function settings are registered on the camera enables you to combine registered settings to add new connection settings. You can also add new connection settings by using connection settings saved to a card.
Page 564 Select a setting method. Select an option and then [OK] to go to the next screen. Select [Configure online] to configure connection settings and then join the network. Select [Configure offline] if you only wish to configure [FTP trans.] and [Browser Remote] connection settings. Select a communication function.
Page 565 Select an item. The options displayed vary depending on the [Select communication function] setting. Select [OK]. Select [New settings]. Select [OK]. By selecting [Select from list] when communication settings are already registered on the camera, you can apply the registered settings.
Page 566 [Configure online] options If you selected [Wired] in step 9, configure the setting as follows. Select an option, then select [OK]. For details on IP address settings, see Setting the IP Address. Select an option, then select [OK]. For details on IPv6 address settings, see Setting the IP Address.
Page 567 [Configure offline] options If you selected [Wired] in step 9, configure the setting as follows. Select an option, then select [OK]. For details on IP address settings, see Setting the IP Address. Select an option, then select [OK]. For details on IPv6 address settings, see Setting the IP Address.
Page 568 Checking the Type of Access Point When connecting via an access point, check whether the access point supports WPS*, which simplifies connections between Wi-Fi devices. If you are unsure about WPS compatibility, refer to the access point user manual or other documentation.
Page 569 Connecting via WPS (PBC Mode) Instructions in this section are continued from Checking the Type of Access Point. This is a connection method used with access points compatible with WPS. In pushbutton connection mode (PBC mode), the camera and access point can be connected simply by pressing the WPS button on the access point.
Page 570 Connect to the access point. Press the access point's WPS button. For details on where the button is and how long to press it, refer to the access point user manual. Select [OK] to initiate connection with the access point. The following screen is displayed once the camera is connected to the access point.
Page 571 Connecting via WPS (PIN Mode) Instructions in this section are continued from Checking the Type of Access Point. This is a connection method used with access points compatible with WPS. In PIN code connection mode (PIN mode), an 8-digit identification number indicated on the camera is entered on the access point to establish a connection.
Page 572 Enter the PIN code. On the access point, enter the 8-digit PIN code displayed on the camera screen. For instructions on entering PIN codes on the access point, refer to the access point's Instruction Manual. After entering the PIN code, select [OK] on the camera. Connect to the access point.
Page 573 Connecting Manually to Detected Networks Instructions in this section are continued from Checking the Type of Access Point. Connect to an access point by selecting its SSID (or ESS-ID) in a list of active access points nearby. Selecting the access point Select an access point.
Page 574 Select a key index. The [Key index] screen is displayed for WEP-encrypted access points. Select the key index number set on the access point. Select [OK]. Enter the encryption key. Press < > to access the virtual keyboard ( ), then enter the encryption key.
Page 575 Connecting Manually by Specifying Networks Instructions in this section are continued from Checking the Type of Access Point. Connect to an access point by entering its SSID (or ESS-ID). Entering the SSID Select [Manual settings]. Enter the SSID (network name). Press <...
Page 576 Setting the access point authentication method Select the authentication method. Select an option and then [OK] to go to the next screen. On the [Encryption settings] screen displayed if [Open system] is selected, select [Disable] or [WEP]. Entering the access point encryption key Enter the encryption key (password) set on the access point.
Page 577 Enter the encryption key. Press < > to access the virtual keyboard ( ), then enter the encryption key. Select [OK] to initiate connection with the access point. The following screen is displayed once the camera is connected to the access point.
Page 578 Connecting in Infrastructure Mode Instructions in this section are continued from Displaying the Connection Wizard. Connect to an access point by entering its SSID (or ESS-ID). Entering the SSID Select [Infrastructure]. Select [OK]. Enter the SSID (network name). Press < >...
Page 579 Setting the access point authentication method Select the authentication method. Select an option and then [OK] to go to the next screen. On the [Encryption settings] screen displayed if [Open system] is selected, select [Disable] or [WEP]. Entering the access point encryption key Enter the encryption key (password) set on the access point.
Page 580 Enter the encryption key. Press < > to access the virtual keyboard ( ), then enter the encryption key. Select [OK] to initiate connection with the access point. The following screen is displayed once the camera is connected to the access point.
Page 581 Connecting in Camera Access Point Mode Instructions in this section are continued from Displaying the Connection Wizard. Camera access point mode is a connection method for directly connecting the camera and other devices via Wi-Fi without using an access point. Two connection methods are available, as follows.
Page 582 Select [Easy connection]. Select [OK]. Select [OK]. The next screen is displayed. Select [OK]. The next screen is displayed.
Page 583 Select [New settings]. Select [OK]. For [Configure online], go to step 6. For [Configure offline], go to step 2 in Configuring Communication Function Settings. By selecting [Select from list] when communication function settings are already registered on the camera, you can apply the registered settings.
Page 584 Computer's screen (sample) Smartphone's screen (sample) Activate Wi-Fi on the other device, then select the SSID (network name) shown on the camera screen. For the password, enter the encryption key (password) shown on the camera screen. Once a connection is established, the settings screen for the communication function is displayed.
Page 585 Connecting with Manual connection Network settings for camera access point mode are configured manually. Set [SSID], [Channel setting], and [Encryption settings] on each screen displayed. Select [Manual connection]. Select [OK]. Enter the SSID (network name). Press < > to access the virtual keyboard ( ), then enter the SSID.
Page 586 Select a channel setting option. To specify the settings manually, select [Manual setting], then turn the < > dial. Select [OK] to initiate connection with the access point. Select an encryption setting option. For encryption, select [AES]. Select [OK]. When [AES] is selected, the [Password] screen is displayed. Press <...
Page 587 Select [Auto setting]. Select [OK]. If an error is displayed for [Auto setting], set the IP address manually Select [OK]. The next screen is displayed. Select [OK]. The next screen is displayed.
Page 588 Select [New settings]. Select [OK]. For [Configure online], go to step 9. For [Configure offline], go to step 2 in Configuring Communication Function Settings. By selecting [Select from list] when communication function settings are already registered on the camera, you can apply the registered settings.
Page 589 Computer's screen (sample) Smartphone's screen (sample) Activate Wi-Fi on the other device, then select the SSID (network name) shown on the camera screen. For the password, enter the encryption key (password) shown on the camera screen. Once a connection is established, the settings screen for the communication function is displayed.
Page 590 Setting the IP Address Instructions in this section are continued from settings used for access point connections. Select a method of setting the IP address, and then set the IP address on the camera. When IPv6 is used, the camera only connects via IPv6. IPv4 connections are disabled. Setting the IP address automatically Set up the IP address settings automatically.
Page 591 Select [OK]. The next screen is displayed. Go to Configuring Communication Function Settings. Setting the IP address manually Set up the IP address settings manually. Note that the items displayed vary depending on the communication function. Select [Manual setting]. Select [OK].
Page 592 Select an option to configure. Select an option to access the screen for numerical input. To use a gateway or DNS address, select [Enable], then select [Address]. Enter the number. Turn the < > dial to switch to other input fields at the top of the screen, and turn the <...
Page 593 Select [OK]. When you have completed setting the necessary items, select [OK]. The next screen is displayed. If you are unsure what to enter, see Checking Network Settings or ask the network administrator or other person in charge of the network. Select an IPv6 option.
Page 594 Select [OK]. The next screen is displayed. Go to Configuring Communication Function Settings.
Page 595 Configuring Communication Function Settings The following instructions are for settings that vary depending on the communication function. Refer to the page that introduces your selected communication function. Select [New settings]. Select [OK] to go to the next screen. By selecting [Select from list] when communication function settings are already registered on the camera, you can apply the registered settings.
Page 596 Complete connection settings for the communication function. FTP transfer ( EOS Utility ( Browser Remote (...
Page 597: Image Transfer To Ftp Servers
Image Transfer to FTP Servers Configuring FTP Server Connection Settings Transferring Images Individually Transferring Multiple Images at Once Adding a Caption Before Transfer Auto Retry If Transfer Fails Viewing Transferred Images By connecting to an FTP server, you can send images on the camera to a computer. With FTP transfer, you can automatically transfer each image to the FTP server as you shoot or transfer a set of images together.
Page 598 Select [Address setting]. Select [OK] to go to the next screen. The virtual keyboard is displayed if you have specified [Auto setting] for the IP address or [Manual setting] for the DNS address. A screen for numerical input is displayed if you have specified [Disable] for the DNS address.
Page 599 Configure the port number. Normally, set [Port number setting] to 00021 (for FTP/FTPS) or 00022 (for SFTP). Select [OK] to go to the next screen. Go to step 6 if you selected [FTP] or [FTPS] in step 1. Go to step 5 if you selected [SFTP].
Page 600 Configure proxy server settings. Not displayed if you selected [FTPS] or [SFTP] in step 1. Select [OK] to go to the next screen. Configure the login method. Not displayed if you selected [SFTP] in step 1. Select [OK] to go to the next screen.
Page 601 Specify a target folder. Select [Root folder] to have images saved in the root folder, as specified in FTP server settings ( Select [Select folder] to specify a target folder in the root folder. If the folder does not exist, it is created automatically. Select [OK] to go to the next screen.
Page 602 Select [OK]. Select [OK]. Display returns to the [Network settings] screen. Connection settings for FTP transfer are now complete. During image transfer, the camera's < > lamp blinks in green.
Page 603 Importing a root certificate for FTPS If you specified [FTPS] FTP mode when configuring connection settings, the root certificate used by the FTP server must be imported to the camera. Only the root certificate with a file name of “ROOT.CER,” “ROOT.CRT,” or “ROOT.PEM” can be imported to the camera.
Page 604 Select [Set root certif]. Select [Load root certif from card]. Select [OK]. The root certificate is imported. Select [OK] on the confirmation screen to return to the [Set root certif] screen. Note To delete the root certificate imported to the camera, select [Delete root certificate] on the screen in step 5.
Page 605 Transferring Images Individually Automatic transfer after each shot Transferring the current image Specifying sizes or types of images to transfer Automatic transfer after each shot Each image can be immediately transferred to the FTP server automatically after your shot. You can continue shooting still photos as usual while images are being transferred. Before shooting, make sure a card is in the camera.
Page 606 Select [FTP transfer settings]. Select [Automatic transfer]. Select [Enable]. Take the picture. The captured image is transferred to the FTP server. Caution Images cannot be erased during image transfer. No voice memo can be added when [Automatic transfer] is set to [Enable].
Page 607 Note During continuous shooting, images are transferred to the FTP server in the order they are captured. Captured images are also stored on the card. Any images for which transfer fails or is interrupted will be transferred automatically when the connection is recovered ( ).
Page 608 Select an image. On the camera, press the < > button. Select an image to transfer, then press < > to transfer the image. You can add a voice memo to the current image before transfer. For details, see Recording Voice Memos.
Page 609 Select the size of images to transfer. Select [JPEG size to trans.], then select [Larger JPEG] or [SmallerJPEG]. To transfer smaller JPEGs when the camera is set to record larger JPEGs to one CFexpress card and smaller JPEGs to the other, set [JPEG size to trans.] to [SmallerJPEG].
Page 610 Select the type of images to transfer. RAW+JPEG transfer • Select [RAW+JPEG transfer], then select [JPEG only], [RAW only], or [RAW+JPEG]. RAW+HEIF transfer • Select [RAW+HEIF transfer], then select [HEIF only], [RAW only], or [RAW+HEIF].
Page 611 Note When the camera is set to record RAW images to one CFexpress card and JPEGs or HEIFs to the other, specify which images to transfer in the [RAW+JPEG transfer] or [RAW+HEIF transfer] setting. Similarly, specify your transfer preference when RAW+JPEG images or RAW+HEIF images are simultaneously recorded to a single card.
Page 612 Transferring Multiple Images at Once Selecting images to transfer Selecting multiple images Transferring RAW+JPEG or RAW+HEIF images After shooting, you can select multiple images and transfer them all at once, or you can transfer unsent images or images that could not be sent previously. You can continue shooting still photos as usual during transfer.
Page 613 Select [FTP transfer]. Select [Sel.Image]. Select the images to transfer. Use the < > dial to select an image to transfer, then press < >. Use the < > dial to add a [ ] in the upper left, then press < >.
Page 614 Select [FTP transfer]. Select [OK]. The selected images are transferred to the FTP server.
Page 615 Selecting multiple images Multiple images can be transferred at once after you choose a selection method. You can continue shooting still photos as usual while images are being transferred. Access the [Image sel./transfer] screen. Follow steps 1–3 in Selecting images to transfer.
Page 616 In a folder • Selecting [Folder images failed transf.] selects all images in the selected folder for which transfer failed. • Selecting [Folder images not transfer'd] selects all unsent images in the selected folder. • Selecting [Clear folder transf. history] clears the transfer history of images in the selected folder.
Page 617 Select [OK]. The selected images are transferred to the FTP server.
Page 618 Transferring RAW+JPEG or RAW+HEIF images For RAW+JPEG or RAW+HEIF images, you can specify which image to transfer. Select [ : Image transfer]. Select the type of images to transfer.
Page 619 RAW+JPEG transfer • Select [RAW+JPEG transfer], then select [JPEG only], [RAW only], or [RAW+JPEG]. RAW+HEIF transfer • Select [RAW+HEIF transfer], then select [HEIF only], [RAW only], or [RAW+HEIF]. Caution Some menu items are not available during image transfer. Note This setting is linked to [RAW+JPEG transfer] and [RAW+HEIF transfer] settings on the [Transfer type/size] screen (...
Page 620 Adding a Caption Before Transfer You can add a registered caption to each image before transfer. This is convenient if you want to inform the recipient of the printing quantity, for example. Captions are also added to images saved to the camera. You can check captions added to images by examining the Exif information, in the user comments.
Page 621 Specify the caption. Select [Caption], and on the screen displayed, select the content of the caption. Select [Transfer]. The image is transferred with the caption. After transfer, display returns to the [Image transfer] screen. Caution Other images cannot be selected from the [Transfer with caption] screen. To select another image for transfer with a caption, view that image before following these steps.
Page 622 Auto Retry If Transfer Fails If transfer fails, the camera's < > lamp blinks in red. In this case, the following screen is displayed after you press the < > button and select [ : Network settings]. To resolve the error displayed, see Troubleshooting. Once you have resolved the issue, the images that could not be sent initially will be transferred automatically.
Page 623 Viewing Transferred Images Images transferred to the FTP server are stored in the following folder as specified in the FTP server settings. Target folder of the FTP server Under the default settings of the FTP server, images are stored in [C drive] → [Inetpub] folder →...
Page 624: Remote Control (Eos Utility)
Remote Control (EOS Utility) Configuring EOS Utility Connection Settings Using EOS Utility Direct Transfer Creating and Registering Captions Using EOS Utility, you can browse images on the camera and save them to the computer. Also in EOS Utility, you can shoot by controlling the camera remotely and change camera settings.
Page 625 Configuring EOS Utility Connection Settings These instructions are continued from Configuring Communication Function Settings. Establishing a connection also requires operations on the computer. For details, refer to the computer documentation. Steps on the camera (1) Select [OK]. The following message is displayed.
Page 626 Steps on the computer Start EOS Utility on the computer. In EOS Utility, click [Pairing over Wi-Fi/LAN]. If a firewall-related message is displayed, select [Yes]. Click [Connect] on the computer. Select the camera to connect to, then click [Connect]. If multiple cameras are listed, identify the camera to connect to by MAC address, as shown on the camera screen.
Page 627 Steps on the camera (2) Select [OK]. This message is displayed after the camera detects the computer where you clicked [Connect] in step 4. Select [OK]. Select [OK]. Select [OK]. Display returns to the [Network settings] screen. The camera's < >...
Page 628 Using EOS Utility For EOS Utility instructions, refer to the EOS Utility Instruction Manual. Remote shooting is only one of the many camera operations available. Caution Some menu items are not available when the camera is connected to a network. In remote shooting, the AF speed may become slower.
Page 629 Direct Transfer With the camera connected to EOS Utility and the main EOS Utility window displayed, you can use the camera to transfer images to computer. Caution Image transfer via FTP in progress is paused while the Live View shooting/movie shooting switch is set to <...
Page 630 Select [Direct transfer]. Select [Sel.Image]. Select an image to transfer. Use the < > dial to select an image to transfer, then press < >. Use the < > dial to add a [ ] in the upper left of the screen, then press <...
Page 631 Select [Direct transfer]. Select [OK]. The selected images are transferred to the computer.
Page 632 Selecting multiple images Multiple images can be transferred at once after you choose a selection method. Access the [Image sel./transfer] screen. Follow steps 1–3 in Selecting images to transfer. Select [Multiple]. Select a selection method to use. Select range • Select [Select range]. Selecting the first and last images of the range marks all the images in the range with a checkmark [ ], and one copy of each image will be sent.
Page 633 In a folder • Selecting [Folder images failed transf.] selects all images in the selected folder for which transfer failed. • Selecting [Folder images not transfer'd] selects all unsent images in the selected folder. • Selecting [Clear folder transf. history] clears the transfer history of images in the selected folder.
Page 634 Select [OK]. The selected images are transferred to the computer.
Page 635 Transferring RAW+JPEG or RAW+HEIF images For RAW+JPEG or RAW+HEIF images, you can specify which image to transfer. Select [ : Image transfer]. Select the type of images to transfer.
Page 636 RAW+JPEG transfer • Select [RAW+JPEG transfer], then select [JPEG only], [RAW only], or [RAW+JPEG]. RAW+HEIF transfer • Select [RAW+HEIF transfer], then select [HEIF only], [RAW only], or [RAW+HEIF]. Caution Some menu items are not available during image transfer. Note This setting is linked to [RAW+JPEG transfer] and [RAW+HEIF transfer] settings on the [Transfer type/size] screen ( Image transfer in progress is paused while the Live View shooting/movie shooting switch is set to <...
Page 637 Creating and Registering Captions You can create captions and register them on the camera to use them as described in Adding a Caption Before Transfer. Start EOS Utility and select [Camera settings]. Select [WFT Captions]. Enter the caption or captions. Enter up to 31 characters (in ASCII format).
Page 638 Set the captions on the camera. Select [Apply to camera] to set your new captions on the camera.
Page 639: Controlling The Camera With Browser Remote
Controlling the Camera with Browser Remote Configuring Browser Remote Connection settings Displaying Browser Remote Browsing Images Shooting Remotely Registering IPTC Information Configuring FTP Server Settings Creating and Registering Captions Using a browser, you can browse and save camera images, shoot remotely, and perform other operations on a computer or smartphone.
Page 640 Configure the [Login name] or [Password]. Select [Login name] and [Password] to access the virtual keyboard ) and enter the login name and password. Select [OK] to return to the screen in step 1. Follow steps 1–2 for each account to be used. Select [OK].
Page 641 Select [OK]. Display returns to the [Network settings] screen. Setting information is stored on the camera. Connection settings for Browser Remote are now complete. Note You can change WFT account settings on the [WFT account] screen ( accessed by selecting [Browser Remote settings] in [Connection option settings].
Page 642 Displaying Browser Remote From a browser, log in to the Browser Remote page on the camera. Make sure the camera and computer are already connected via a wired LAN connection. Checking the camera's IP address The camera's IP address, as displayed in step 5, must be entered in the browser address bar to access the camera from a browser.
Page 643 Select [Confirm settings]. Setting details are displayed. Check the settings. Turn the < > dial to access other pages. Write down the IP address. After checking, press the < > button to close the confirmation screen. Logging in to Browser Remote Start a browser.
Page 644 Enter the information for [Login name] and [Password]. In [Login name] (user name) and [Password], enter the information you specified in Configuring Browser Remote Connection settings. Select [OK] to display the top Browser Remote menu screen. Configure default settings as needed. Select [ ] to display the menu.
Page 645 • Language Enables you to select the display language. • Display theme You can set the Browser Remote background color. Select [Dark] or [Light]. • AF for still photo shooting Displayed if you select [Shooting] in step 9. Enables you to configure autofocus operation for still photo shooting.
Page 646 • Secure transfer Enables you to download a root certificate and access an FTP server, when you will connect to the FTP server via HTTPS. • Log out Select to end the Browser Remote connection. Caution Browser Remote is not available unless the browser support JavaScript. Some menu items are not available when connected to the camera.
Page 647 Browsing Images Enables you to browse images on cards in the camera. Select [Playback]. The image browsing screen is displayed.
Page 648 Select a card and folder. Select a card in the pull-down list at left. Select a folder in the pull-down list at right. Perform image operations as needed.
Page 649 Selecting [Update] displays any images that have been added. With [Select] selected, you can select multiple images. Selecting individual thumbnails selects each image separately. Selecting thumbnails again clears the selection. Selecting [Select all] marks all images on the browsing screen as selected.
Page 650 Selecting a thumbnail switches to the playback screen and shows the image enlarged. Still photo playback screen Movie playback screen...
Page 651 Audio playback screen Selecting an image and then [ ] erases the image. Selecting an image and then the [ ] button downloads the image to the computer. Note Computer performance and the browser used may prevent or delay image display or prevent image downloading.
Page 652 Shooting Remotely You can use Browser Remote to shoot remotely. Shooting still photos Select [Shooting]. The remote shooting screen is displayed.
Page 653 Still photo shooting button Movie shooting button Multi-function lock icon Shutter button MF toggle button HDR shooting Image quality Browser Remote connection Battery level (10) Drive mode (11) Available shots (12) AF operation (13) AF button (14) Shooting mode (15) Shutter speed (16) Aperture value...
Page 654 Select (1) Still photo shooting button. Set the lens's focus mode switch to < >. Display the Live View image. To activate or deactivate Live View, select (26) Live View shooting button. For more responsive Live View image display, select (27) Live View image quality toggle button, which will reduce Live View image quality to improve responsiveness.
Page 655 Set up shooting. Select setting items (such as image quality) to view the setting details, which you can configure. Configure the settings as needed.
Page 656 Focus on the subject. When using autofocus To start AF with [AF button] selected in the [AF for still photo shooting] menu, select the (13) AF button. To start AF with [Shutter button for AF/shooting] selected in the [AF for still photo shooting] menu, select and release (4) Shutter button. When focusing manually To show/hide (25) MF button display, select (5) MF toggle button.
Page 657 Take the picture. Select (4) Shutter button, and when you release the button, the camera shoots. Captured images are saved to the card in the camera. To browse and download images, see Browsing Images. Caution Depending on the communication status, image display or shutter release timing may be delayed.
Page 658 Recording movies Select [Shooting]. The remote shooting screen is displayed. Select (2) Movie shooting button. Configure settings as needed. Follow steps 3–6 in Shooting still photos.
Page 659 Record the movie. Movie recording standby Movie recording in progress Select (4) Shutter button, and when you release the button, movie recording begins. During movie recording, the red [○] on (4) Shutter button changes to a white [□]. To stop movie recording, select (4) Shutter button again and release the button.
Page 660 Registering IPTC Information Enables you to edit and register IPTC* information (comments on images, such as captions, credits, and shooting locations) on the camera. Images can be tagged with IPTC information registered on the camera. * International Press Telecommunications Council Select [IPTC info].
Page 661 Edit and register information as needed. Selecting [Add to camera] to applies the edited IPTC information to the camera. This also sets the camera's Custom Function [ 8: Add IPTC information] option to [ Selecting [Clear camera info] deletes all IPTC information registered on the camera.
Page 662 Configuring FTP Server Settings If you will use FTP transfer for images captured remotely, you can use the camera's connection settings ( ) to change the target FTP server. Select [FTP settings]. The FTP setting screen is displayed.
Page 663 Select registered connection settings of the FTP server to use. Select [Change setting]. The camera's connection settings are changed to your selected settings.
Page 664 Creating and Registering Captions You can create captions and register them on the camera to use them as described in Adding a Caption Before Transfer. Select [FTP settings]. The FTP setting screen is displayed.
Page 665 Enter the caption or captions. Enter up to 31 characters (in ASCII format). To acquire caption data stored on the camera, select [Get from camera]. Set the captions on the camera. Select [Add to camera] to set your new captions on the camera.
Page 666: Ending Connections Or Reconnecting
Ending Connections or Reconnecting Ending Connections Reconnecting Ending Connections Select [ : Network settings]. Select [Connection settings]. Select [Disconnect]. The devices are disconnected.
Page 667 Reconnecting Select [ : Network settings]. Select [Connection settings]. Select [SET*]. In the saved settings, select settings to use for the connection. Select [Connect].
Page 668 Select [OK]. The devices are connected again. If settings were changed on the target device, restore the previous settings to enable connections by the camera.
Page 669: Checking And Editing Network Settings
Checking and Editing Network Settings Checking and Editing Connection Settings Manually Editing Connection Settings Specifying Connection Options Checking the MAC Address Checking and Editing Connection Settings You can check, change, or delete connection settings saved on the camera. Select [ : Network settings].
Page 670 Select [SET*]. In the saved settings, select settings to use for the connection. Check or change the settings.
Page 671 Connect • Select to re-establish a connection ( Change with wizard/Change from list • Change connection settings ( Save/load settings on card • Save connection settings to a card, or load saved connection settings from a card into the camera ( Delete settings •...
Page 672 Changing connection settings Settings originally completed using the connection wizard can be changed as follows. Change with wizard You can use the connection wizard to change connection settings saved on the camera. Access the [Connection settings] screen. Follow steps 1–3 in Checking and Editing Connection Settings.
Page 673 Change from list You can use communication and function settings saved on the camera to change connection settings saved on the camera. You can also register settings names. Access the [Connection settings] screen. Follow steps 1–3 in Checking and Editing Connection Settings.
Page 674 NW*/Comm settings* • Select to change, add, or clear communication settings. • Selecting [Select from list] lists communication settings saved on the camera. Select the communication settings to use. • Selecting [Clear selected] clears communication settings with registered connection settings. Select [OK] on the confirmation screen. MODE*/Function settings* •...
Page 675 Saving and loading settings Connection settings can be saved on a card and applied to other cameras. Connection settings configured on other cameras can also be applied to the camera you will use. Note [ : Save/load cam settings on card] enables you to save all communication settings on the camera to a card or load all communication settings for another camera from a card.
Page 676 Select [OK]. The file name is determined automatically by the camera: WFTNPF, followed by a number (01 to 40) and the extension NIF. To rename the file as desired, press the < > button. The settings are saved to the card. The settings file is saved to an area of the card shown when the card is opened (in the root directory).
Page 677 Loading settings Access the [Connection settings] screen. Follow steps 1–3 in Checking and Editing Connection Settings. Select [Save/load settings on card]. Select [Load settings from card]. Select a settings file. Select a settings file that matches your network environment.
Page 678 Select [OK]. Information from the settings file is loaded into the selected settings number. Caution Even if a computer or other device is used to save more than 41 settings files on a card, only 40 are displayed on the camera's screen for loading settings. To load more than 41 settings files, load 40 from one card, then load remaining files from another card.
Page 679 Manually Editing Connection Settings You can add, change, or delete communication and function settings saved on the camera. You can also configure settings that are not set using the connection wizard, such as a setting that determines what happens if files with the same name as existing files are sent to the FTP server.
Page 680 Select [NW*]. Select settings labeled [Unspecified] or other saved settings to edit. Change, delete, or check the settings as needed.
Page 681 Change • Select to change individual settings in sets of communication settings. • Selecting [Wireless LAN] enables you to change the target SSID, for example. • Selecting [TCP/IPv4] enables you to configure network-related settings such as the IP address. • Selecting [TCP/IPv6] enables you to configure settings used for IPv6 ( •...
Page 682 Editing function settings Select [ : Network settings]. Select [Manual setting]. Select [Function settings]. Select [MODE*]. Select settings labeled [Unspecified] or other saved settings to edit.
Page 683 Change, delete, or check the settings as needed. Change • Only available when editing FTP transfer settings. • Selecting [FTP server] enables you to configure settings related to the FTP server. Directory structure of the target folder Overwriting files of the same name Passive mode Trusting target servers Delete settings...
Page 684 Confirm settings • Select to check function settings.
Page 685 Directory structure of the target folder Configured in [FTP server] → [Directory structure]. With [Default], the root folder is used for image storage. If you have created a subfolder in the root folder by changing the [Target folder] setting, images are saved in that folder. Selecting [Camera] automatically creates a folder structure matching that of the camera's (such as A/DCIM/100EOS1D) in the server's root folder for image storage.
Page 686 Specifying Connection Options You can configure settings used for FTP transfer and Browser Remote. Settings are also available for authentication information used in LAN environments with 802.1X authentication. Select [ : Network settings]. Select [Connection option settings]. Select an item to configure. FTP transfer settings Browser Remote settings 802.1X authentication...
Page 687 FTP transfer settings Selecting [FTP transfer settings] enables you to configure settings related to FTP transfer and power saving. Automatic transfer/Transfer type/size/Transfer with SET/Set root certif • For details, see Image Transfer to FTP Servers. Power saving • When [Enable] is set and no image is transferred for a certain period, the camera will log off from the FTP server and disconnect from the LAN.
Page 688 Browser Remote settings Selecting [Browser Remote settings] enables you to set the account used for Browser Remote access and configure HTTP/HTTPS communication settings. WFT account • For details, see Configuring Browser Remote Connection settings. Port no. (HTTP)/Port no. (HTTPS) • You can change the port number used for HTTP/HTTPS communication. There is normally no need to change the port number (80 for HTTP, 443 for HTTPS).
Page 689 802.1X authentication Selecting [802.1X authentication] enables you to set, check, or delete 802.1X authentication settings, using a setup wizard. Configure these settings when connecting to networks that require 802.1X authentication. First, save the certificate for the type of 802.1X authentication used to a card in the camera. File types and names that can be loaded using this function are as follows.
Page 690 Checking the MAC Address You can check the camera's MAC address. Select [ : Network settings]. Select [MAC address]. Check the MAC address. The MAC addresses for [Wi-Fi] and [Wired] are displayed.
Page 691: Syncing Time Between Cameras
Syncing Time Between Cameras Preparing for Time Syncing Syncing the Time You can set the sender camera time on up to 10 receiver cameras. Note that even after synchronization, a slight margin of error applies between sender and receiver camera time (of ±0.05 seconds, at most).
Page 692 Preparing for Time Syncing When using a single receiver camera, connect a LAN cable to the Ethernet terminal of the sender and receiver cameras. (A) Sender camera (B) Receiver camera (C) LAN cable When using multiple receiver cameras, connect a LAN cable from the Ethernet terminal of the sender and receiver cameras to a hub.
Page 693 Syncing the Time Preparing the sender camera First, set up the camera to use as a sender. On the camera, press the < > button. Select [ : Network settings]. Select [Enable]. Select [Sync time between cameras]. If the camera is already connected to another device, [Set [Connection settings] to [Disconnect]] is displayed.
Page 694 Select [OK]. Select [OK]. Select [Sender]. Select [OK] to go to the next screen. After the screen is displayed, the camera is ready.
Page 695 Preparing receiver cameras Set up cameras to use as receivers. Follow steps 1–6 in Preparing the Sender Camera. Select [Receiver]. Select [OK] to go to the next screen. Select [OK]. The following screen is displayed. To set the time on multiple receiver cameras, follow steps 1–2 on each receiver camera.
Page 696 Syncing time between sender and receiver cameras Sync the time on the sender and receiver cameras as follows. Follow steps 1–6 in Preparing the sender camera and steps 1–3 in Preparing receiver cameras. On the sender camera, select [OK]. Check the number of receiver cameras, then select [OK]. After the time is synchronized, the next screen is displayed.
Page 697: Gps Features
GPS Features GPS Settings GPS Precautions GPS features of the camera can be used to geotag images, set the time, and more. The camera can receive signals from GPS satellites (USA), GLONASS satellites (Russia), and the Quasi-Zenith Satellite System “Michibiki” (Japan). Caution Geotag information may not be recorded or inaccurate information may be recorded where GPS signal coverage is poor, such as in the following places.
Page 698 GPS Settings Select [ : GPS settings]. Configure GPS details.
Page 699 [GPS] Specify the GPS operating mode. In [Mode 1], the camera continues to acquire GPS signals at regular intervals with the power switch set to < > or even < >. In [Mode 2], the camera acquires GPS signals with the power switch set to < >.
Page 700 [Auto time setting] Time information acquired from GPS signals can be set on the camera. The margin of error is approx. ±0.02 sec. Selecting [Auto update] will update the time when GPS signals are received while the camera is on. Caution The time cannot be automatically updated unless signals from at least five GPS satellites can be acquired.
Page 701 [GPS information display] Shows acquired GPS information. The < > icon indicates signal conditions. When [ ] is displayed, elevation is also recorded. Note that elevation is not recorded when [ ] is displayed. You can check geotag information by displaying a shot, pressing the < >...
Page 702 GPS Logger By setting [Log GPS position] to [Enable], you can automatically record geotag information at specific intervals along the route that the camera travels. Geotag information is recorded at the interval set in [Position update intvl] as log data saved in the camera's internal memory by date.
Page 703 Transferring log data to a card You can transfer recorded log data to a card selected in [Transfer log data to card]. Transferring log data to a card erases the data from the camera's internal memory. Log files transferred to a card are stored in the “GPS” folder within the “MISC” folder. They are saved with a “.LOG”...
Page 704 To avoid violating GPS regulations, visit the Canon website to check where use is allowed. Note that Canon cannot be held liable for any problems arising from use of GPS functions in other countries and regions.
Page 705: Reference
Reference Changing the Camera Nickname Virtual Keyboard Operations Configuring IPv6 Changing the Camera Nickname You can change the nickname of this camera (displayed on connected devices) as desired. Select [ : Nickname]. Enter text using the virtual keyboard. When you finish entering characters, press the < >...
Page 706 Select [OK].
Page 707 Virtual Keyboard Operations Input area, for entering text Cursor keys, for moving in the input area Current no. of characters/no. available Keyboard Switch input modes Space Delete a character in the input area Finish the text entry Use < > or the < >...
Page 708 Configuring IPv6 To use IPv6, configure the settings manually. Note If you are unsure what to enter, ask the network administrator or other person in charge of the network. Select [ : Network settings]. Select [Manual setting]. Select [Comm settings].
Page 709 Select the communication settings that will use IPv6. Select [Change]. Select [TCP/IPv6]. Select an item to configure.
Page 710 Use TCP/IPv6 • Select [Enable] or [Disable] for IPv6. Manual setting • To set the IP address manually, select [Enable]. [DNS server] is set to [Manual setting], and you can configure [DNS address], [Manual address], [Prefix length], and [Gateway]. DNS server •...
Page 711 DNS address/Manual address/Gateway • Select an item and enter the IP address. Prefix length • To set the prefix length, turn the < > dial to select a value (1–128).
Page 712: Troubleshooting
Troubleshooting Responding to Error Messages Troubleshooting Guide Communication Function Precautions Security Checking Network Settings Responding to Error Messages Resolve any errors displayed on the camera screen by referring to these examples of corrective actions. When errors occur, the < > lamp on the camera blinks and the error number is shown on the LCD panel.
Page 713 11: Connection target not found In the case of [Smartphone], is Camera Connect running? • Establish a connection using Camera Connect ( In the case of [EOS Utility], is EOS Utility running? • Start EOS Utility and try to connect again ( Are the camera and the access point set to use the same encryption key for authentication? •...
Page 714 21: No address assigned by DHCP server What to check on the camera On the camera, the IP address is set to [Auto setting]. Is this the correct setting? • If no DHCP server is used, configure the setting after setting the IP address to [Manual setting] on the camera ( What to check on the DHCP server Is the power of the DHCP server on?
Page 715 22: No response from DNS server What to check on the camera On the camera, the DNS address is set to [Manual setting]. Is this the correct setting? • If no DNS server is used, set the camera's DNS address setting to [Disable] ( On the camera, does the DNS server's IP address setting match the server's actual address? •...
Page 716 41: Cannot connect to FTP server What to check on the camera The camera's proxy server setting is [Enable]. Is this the correct setting? • If no proxy server is used, set the camera's proxy server setting to [Disable] ( Do the camera's [Address setting] and [Port No.] settings match those of the proxy server? •...
Page 717 On the camera, does the FTP server's IP address setting (in [Address]) match the server's actual address? • Configure the IP address on the camera to match the actual FTP server address Is the FTP server configured to restrict access to only some IP addresses? •...
Page 718 43: Cannot connect to FTP server. Error code received from server. What to check on the proxy server Is the proxy server on? • Turn on the proxy server. Is the proxy server working correctly? • Check the proxy server settings to make sure the server is working correctly as a proxy server.
Page 719 45: Cannot login to FTP server. Error code received from server. What to check on the camera On the camera, is the [Login name] set correctly? • Check the login name for accessing the FTP server. Check upper- and lower-case letters, and make sure the correct login name is set on the camera ( On the camera, is the [Login password] set correctly? •...
Page 720 47: Image file transfer completion not confirmed by FTP server This error occurs from a failure to receive confirmation from the FTP server that image file transfer is complete for some reason. • Restart the FTP server and camera and send the images again. 48: Security of the connection to the target server cannot be verified.
Page 721 63: Wireless LAN authentication failed Are the camera and the access point set to use the same encryption key for authentication? • Check upper- and lower-case letters, and make sure the correct encryption key for authentication is set on the camera ( If filtering by MAC address is active, is the MAC address of the camera in use registered at the access point? •...
Page 722 67: Incorrect wireless LAN encryption method Are the camera and the access point set to use the same encryption method? • The camera supports the following encryption methods: WEP, TKIP, and AES ( If filtering by MAC address is active, is the MAC address of the camera in use registered at the access point? •...
Page 723 72: Cannot connect to sender camera Are you following the correct procedure to establish the connection with the sender camera? • Operate the sender camera by following the correct instructions. Is the sender camera too far from the receiver cameras? •...
Page 724 Troubleshooting Guide Troubleshoot camera issues by checking the camera and connected devices as described in this section. If troubleshooting does not resolve the problem, contact a Canon Service Center for product information and advice on product handling. Cannot transfer images to an FTP server.
Page 725 Communication Function Precautions In case of slower transmission, lost connections, choppy image display, or other problems when using communication functions, try the following corrective actions. Access point and antenna installation location When using the camera indoors, install the access point in the same room where you are shooting.
Page 726 Security If security settings have not been properly set, the following problems may occur. Transmission monitoring Third parties with malicious intent may monitor wireless LAN transmissions and attempt to acquire the data you are sending. Unauthorized network access Third parties with malicious intent may gain unauthorized access to the network you are using to steal, modify, or destroy information.
Page 727 Checking Network Settings Windows Open the Windows [Command Prompt], then enter ipconfig/all and press the <Enter> key. In addition to the IP address assigned to the computer, the subnet mask, gateway, and DNS server information are also displayed. macOS In macOS, open the [Terminal] application, enter ifconfig -a, and press the <Return> key.
Page 728: Resetting Communication Settings
Resetting Communication Settings All settings of network features can be cleared. This can prevent the information from being leaked if you lend the camera or transfer ownership. Select [ : Reset communication settings]. Select [OK]. Caution If you have paired the camera with a smartphone, on the smartphone's Bluetooth settings screen, delete the connection information of the camera for which you restored default wireless communication settings.
Page 729: Set-Up
Set-up This chapter describes menu settings on the set-up ([ : Set-up]) tab. • Tab Menus: Set-up • Selecting Cards for Recording/Playback • Folder Settings • File Numbering • File Naming • Auto Rotate • Formatting • Display Brightness • Display Color Tone •...
Page 730: Tab Menus: Set-Up
Tab Menus: Set-up Set-up 1 (1) Record func+card/folder sel. • Selecting Cards for Recording/Playback • Creating a Folder File numbering File name Auto rotate Format card Disp. brightness Disp. color tone Set-up 2 Auto power off Date/Time/Zone Language Viewfinder display button display options Custom Quick Control...
Page 731 Set-up 3 UI magnification Help text size Video system Touch control Beep Battery info. Sensor cleaning Set-up 4 HDMI resolution Save/load cam settings on card Custom shooting mode (C1-C3) Reset camera Copyright information...
Page 732 Set-up 5 System status display Manual/software URL Certification Logo Display Firmware Caution [Firmware] is not displayed in Live View shooting or movie recording. In Live View shooting, the following screen is displayed for [ 2]. Auto power off Date/Time/Zone Language Shooting info.
Page 733 In movie recording, the following screen is displayed for [ 2]. Auto power off Date/Time/Zone Language Shooting info. disp. Shutter btn function for movies...
Page 734: Selecting Cards For Recording/Playback
Selecting Cards for Recording/Playback Recording Method with Two Cards Inserted Recording/Playback Selection with Two Cards Inserted Recording is possible when card [ ] or [ ] is in the camera (except under some conditions). With only one card inserted, there is no need to follow these steps. With two cards inserted, you can select the recording method and card to use for recording and playback as follows.
Page 735 Set the recording method. separate Select [Enable] for automatic configuration of the recording method for still photos and movies. Still photos are recorded to card movies to card . Still photo shooting is not possible if card is full or not inserted. Movie recording is not possible if card is full or not inserted.
Page 736 Rec options Set the recording method for still photos. • Standard Records still photos to the card selected in [ Record/play]. • Auto switch card Same as [Standard], but additionally, the camera switches to the other card when one card becomes full. When the camera switches cards, a new folder is created.
Page 737 Note Rec. separately/Rec. to multiple Images are recorded with the same file number to card The number of shots available shown in the viewfinder and top LCD panel is the quantity on the card with less available space. [Card* full] is displayed when one of the cards becomes full, and shooting is no longer possible.
Page 738 Recording/Playback Selection with Two Cards Inserted With [ Rec options]/[ Rec options] set to [Standard] or [Auto switch card], select the card for recording and playback. With [ Rec options] set to [Rec. separately] or [Rec. to multiple], or with [ options] set to [ ], select the card for playback.
Page 739 Note With [Priority: ] set, the camera switches to the priority card when cards are inserted or removed. Setting size via the rear LCD panel Press the < > button ( Select a card. Turn the < > dial to select a card. The card labeled with <...
Page 740: Folder Settings
Folder Settings Creating a Folder Renaming Folders Selecting a Folder You can freely create and select the folder where the captured images are to be saved. You can also rename folders. Creating a Folder Select [ : Record func+card/folder sel.]. Select [Folder].
Page 741 Select [Create folder]. Select [OK]. To rename the folder, select [Change folder name].
Page 742 Renaming Folders Enter letters and numbers of your choice. You can enter five characters. By selecting [ ], you can change the input mode. To delete single characters, select [ ] or press the < > button. Use the < >...
Page 743 Selecting a Folder (1) Number of images in folder (2) Lowest file number (3) Folder name (4) Highest file number Select a folder on the folder selection screen. Captured images are stored in your selected folder. Note Folders Folders are named as in “100EOS1D,” with a three-digit folder number followed by five letters or numbers.
Page 744: File Numbering
File Numbering Continuous Auto Reset Manual Reset The captured images saved in a folder are assigned a file number from 0001 to 9999. You can change how the image files are numbered. (Example) (1) File number Select [ : File numbering].
Page 745 Set the item. Select [Numbering]. Select [Continuous] or [Auto reset]. If you want to reset the file numbering, select [Manual reset] ( Select [OK] to create a new folder, and the file number will start with 0001. Caution If the file number in folder 999 reaches 9999, shooting will not be possible even if the card still has free space.
Page 746 Continuous For continuous file numbering regardless of switching cards or creating folders File numbering is continuous up to 9999, even if you replace a card, create a folder, or switch the target card (as in → ). This is useful when you want to save images numbered anywhere between 0001 to 9999 on multiple cards or in multiple folders into one folder on a computer.
Page 747 Auto Reset For restarting file numbering from 0001 after switching cards or creating folders File numbering is reset to 0001 if you replace a card, create a folder, or switch the target card (as in → ). This is useful if you want to organize images by cards or folders. Note that file numbering may continue from any existing images in cards or folders that you switch to.
Page 748 Manual Reset For resetting file numbering to 0001 or starting from 0001 in new folders When you reset the file numbering manually, a new folder is created automatically and the file numbering of images saved to that folder starts from 0001. This is useful, for example, if you want to use different folders for the images taken yesterday and the ones taken today.
Page 749: File Naming
File Naming Registering/Changing File Names File names consist of four alphanumeric characters followed by a four-digit file number ( and file extension. You can change the first four alphanumeric characters, which by default are unique for each camera and set when the camera is shipped. User setting 1 enables you to register four characters of your choice.
Page 750 Enter letters and numbers of your choice. Enter four characters for User setting 1 or three for User setting 2. By selecting [ ], you can change the input mode. To delete single characters, select [ ] or press the < >...
Page 751 Select a registered file name. Select [File name], then choose a registered file name. Caution An underscore (“_”) cannot be used as the first character. Note User setting 2 Shooting after you have selected “*** + image size” (as registered to User setting 2) will add a character representing the current image size to your file name as the fourth character.
Page 752: Auto Rotate
Auto Rotate You can change the auto rotation setting that straightens images shot in vertical orientation when they are displayed. Select [ : Auto rotate]. Select an item. Automatically rotates images for display on both the camera and computers. Automatically rotates images only for display on computers. Images are not automatically rotated.
Page 753 Caution Images captured with auto rotation set to [Off] will not rotate during playback even if you later set auto rotation to [On]. Note If a picture is taken while the camera is aimed up or down, automatic rotation to the proper orientation for viewing may not be performed correctly.
Page 754: Formatting
Formatting If the card is new or was previously formatted (initialized) by another camera or computer, format the card with this camera. Caution When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep.
Page 755 Format the card. Select [OK]. For low-level formatting, press the < > button to add a checkmark < > to [Low level format], then select [OK].
Page 756 Conditions requiring card formatting The card is new. The card was formatted by a different camera or a computer. The card is full of images or data. A card-related error is displayed ( Low-level formatting Perform low-level formatting if the card's writing or reading speed seems slow or if you want to totally erase the data on the card.
Page 757: Display Brightness
Display Brightness Select [ : Disp. brightness]. Make the adjustment. Referring to the gray image, turn the < > dial to adjust brightness, then press < >. Note To check the image's exposure, referring to the histogram is recommended ( You can also access the screen in step 2 by pressing the <...
Page 758: Display Color Tone
Display Color Tone Select [ : Disp. color tone]. Make the adjustment. Turn the < > dial to select an item, then press < >.
Page 759: Auto Power Off
Auto Power Off You can change the idle auto power off time. Select [ : Auto power off]. Select an item. Note The screen turns off in approx. 30 min. even when set to [Disable]. Note that the camera remains on.
Page 760: Date/Time/Zone
Date/Time/Zone When you turn on the power for the first time or if the date/time/zone have been reset, follow these steps to set the time zone first. By setting the time zone first, you can simply adjust this setting as needed in the future and the date/time will be updated to match it.
Page 761 Turn the < > dial to select the time zone, then press < >. If your time zone is not listed, press the < > button, then set the difference from UTC in [Time difference]. Turn the < > dial to select a [Time difference] item (+/–/hour/ minute), then press <...
Page 762 After changing [Zone/Time difference], check that the correct date/time are set. When you will use [Sync time between cameras] over a wired LAN or with a Wireless File Transmitter, use other EOS-1D X Mark III cameras. [Sync time between cameras] cannot be used with different models.
Page 763 Note Auto power off time may be extended while the [ : Date/Time/Zone] screen is displayed. The time can be set or updated automatically using GPS (...
Page 764: Language
Language Select [ : Language Set the desired language.
Page 765: Viewfinder Information Display
Viewfinder Information Display Electronic Level Grid Information Display in Viewfinder Electronic Level Displays an electronic level at the top of the viewfinder when the shutter button is pressed halfway. Also available in vertical shooting. Select [ : Viewfinder display]. Select [Electronic level].
Page 766 Select [Show]. (1) 1° (2) 4° or more (3) 1° (4) 7° (5) 7.5° or more Caution There may be a margin of error of approx. ±1°.
Page 767 Grid Displays a grid in the viewfinder to help you check camera tilt and shot composition. Select [ : Viewfinder display]. Select [Grid display].
Page 768 Select [Show]. Note You can display a grid on the screen during Live View shooting and before you start recording a movie (...
Page 769 Information Display in Viewfinder Setting information can be displayed in the viewfinder for these shooting functions: shooting mode, metering mode, white balance, drive mode, image quality, AF operation, and flicker detection. By default, only flicker detection is selected ([ ]). Select [ : Viewfinder display].
Page 770 Add a checkmark [ ] to items to display. Select information to display and press < > to add a checkmark [ ]. Repeat this step to add a checkmark [ ] to all information to display, then select [OK]. Note Regardless of the [ ] setting, relevant information appears in the viewfinder when you press the <...
Page 771: Info> Button Display Options
<INFO> Button Display Options Electronic Level Quick Control Screen Custom Quick Control Screen You can specify the information displayed in response to pressing the < > button when the camera is ready to shoot. Select [ : button display options]. Select an item.
Page 772 Electronic Level The red line turns green when the image is essentially straight. (1) Vertical (2) Horizontal Caution There may be a margin of error of approx. ±1°. If the camera is very tilted, the electronic level's margin of error will be larger.
Page 773 Quick Control Screen Quick Control Screen (in Viewfinder Shooting).
Page 774 Custom Quick Control Screen Custom Quick Control.
Page 775: Custom Quick Control
Custom Quick Control Resetting the Custom Quick Control Screen or Clearing All Items Unlike the fixed layout and predetermined shooting features on the Quick Control screen ), this screen can be customized with your preferred shooting features and layout. This function is called “Custom Quick Control.”...
Page 776 Review the instructions and select [OK]. By default, the layout includes the items shown here.
Page 777 Add an item. Press the < > button. Turn the < > dial or use < > to select an item to add, then press < >. To remove an item, either select the item and press the < > button or select [Clear all items] in step 2.
Page 778 Arrange the item. Turn the < > or < > dial or use < > to move the added item (in the frame with arrows) into position. To change the display size, press the < > button and resize the item as needed.
Page 779 Exit the setting. When finished, press the < > button to return to the screen in step 2. Review your setting screen. Sample screen Confirm that [Custom Quick Control screen] in [ : button display options] has a checkmark [ ] ( Press the <...
Page 780 Resetting the Custom Quick Control Screen or Clearing All Items To restore the default Custom Quick Control screen layout, select [Revert layout to default] in step 2 ( To remove all items from the layout (so that the screen is blank except for the bottom row), select [Clear all items].
Page 781 Caution The amount of information that can be shown and the features available for Quick Control vary by item, due to differences in display size. The same item cannot be arranged in multiple positions on the screen.
Page 782: Shooting Information Display
Shooting Information Display Customizing Information on the Screen Grid Histogram Clearing Settings You can customize on-screen display in Live View shooting or movie recording. Customizing Information on the Screen Select [ : Shooting info. disp.]. Select [Screen info. settings].
Page 783 Select screens. Turn the < > dial to select screens of information to show on the camera. For information you prefer not to display, press < > to clear the checkmark [ ]. To edit the screen, press the < >...
Page 784 Grid Select [ : Shooting info. disp.]. Select [Grid display]. Select an item.
Page 785 Histogram Select [ : Shooting info. disp.]. Select [Histogram disp]. Select an item. Select the content ([Brightness] or [RGB]) and display size ([Large] or [Small]). Press < > button to confirm the setting.
Page 786 Clearing Settings Select [ : Shooting info. disp.]. Select [Reset]. Select [OK].
Page 787: Shutter Button Function For Movies
Shutter Button Function for Movies You can set the functions performed by pressing the shutter button halfway or completely during movie recording. Caution In movie recording, the [Shutter btn function for movies] setting overrides any function assigned to the shutter button in [ 6: Custom Controls].
Page 788 Select an item. Half-press Specify the function performed by pressing the shutter button halfway. Fully-press Specify the function performed by pressing the shutter button completely. With [Fully-press] set to [Start/stop mov rec], you can start/stop movie recording not only with the movie shooting button but also by pressing the shutter button completely, or by using Remote Switch RS-80N3 or Timer Remote Controller TC-80N3 (both sold separately).
Page 789: Ui Magnification
UI Magnification You can magnify menu screens by double-tapping with two fingers. Double-tap again to restore the original display size. Magnification is also available on the Quick Control screen in viewfinder shooting, the Custom Quick Control screen, and the electronic level screen. Select [ : UI magnification].
Page 790: Help
Help Changing the Help Text Size When [ Help] is displayed, you can display a description of the feature by pressing the < > button. Press it again to exit Help display. To scroll the screen when a scrollbar (1) appears on the right, turn the <...
Page 791 Example: [ 6: Multi function lock] < >...
Page 792 Changing the Help Text Size Select [ : Help text size]. Select an item.
Page 793: Video System
Video System Set the video system of any television used for display. This setting determines the frame rates available when you record movies. Select [ : Video system]. Select an item. For NTSC For areas where the TV system is NTSC (North America, Japan, South Korea, Mexico, etc.).
Page 794: Touch Control
Touch Control Select [ : Touch control]. Select an item. [Sensitive] makes the touch-screen panel more responsive than [Standard]. To disable touch operations, select [Disable]. Caution Precautions for touch-screen operations Do not use sharp objects such as fingernails or ballpoint pens for touch operations. Do not use wet fingers for touch operations.
Page 795 Note Touch-activated shooting (touch shutter) is not supported.
Page 796: Beeps
Beeps Select [ : Beep]. Select an item. Enable The camera beeps after focusing and in response to touch operations. Touch Disables beeping for touch operations. Disable Disables beeping after focusing and in response to touch operations.
Page 797: Battery Information
(Green): Battery's recharge performance is slightly degraded. (Red): Purchasing a new battery is recommended. Caution Using a genuine Canon Battery Pack LP-E19 is recommended. If you use batteries that are not genuine Canon products, the camera's full performance may not be attained or malfunction may result.
Page 798 Note The shutter count is the number of still photos taken (not including movie recording). Charging the Battery if [Calibration is recommended when charging battery next time] is displayed. If a battery communication error message is displayed, follow the instructions in the message.
Page 799: Sensor Cleaning
Sensor Cleaning Cleaning Now Cleaning Automatically Cleaning Manually The camera's sensor cleaning feature cleans the front of the image sensor. Note For best results, clean with the camera in a stable position on a desk or other flat surface. Cleaning Now Select [ : Sensor cleaning].
Page 800 Select [Clean now Select [OK] on the confirmation screen. Note Even if you repeat the sensor cleaning, the result will not improve much. Note that [Clean now ] may not be available immediately after cleaning. Dots of light may appear in captured images or on the shooting screen if the sensor is affected by cosmic rays or similar factors.
Page 801 Cleaning Automatically Select [Auto cleaning Select an item. Turn the < > dial to select an item, then press < >.
Page 802 Always use a fully charged battery. The image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Select [ : Sensor cleaning]. Select [Clean manually].
Page 803 If the battery level becomes low while cleaning the sensor, the beeper will sound as a warning. Stop cleaning the sensor. If a smudge that cannot be removed with a blower remains, having the sensor cleaned by a Canon Service Center is recommended.
Page 804: Hdmi Resolution
HDMI Resolution Set the image output resolution used when the camera is connected to a television or external recording device with an HDMI cable. Select [ : HDMI resolution]. Select an item. Auto The images will automatically be displayed at the optimum resolution matching the connected television.
Page 805: Save/Load Settings On Card
By loading a camera settings file, you can apply the state of the settings as saved. This enables you to save optimal settings for particular scenes or subjects, or load settings files on other EOS-1D X Mark III cameras to use the cameras with the same settings.
Page 806 Naming. The steps are the same. Caution Camera settings files saved by a camera other than an EOS-1D X Mark III cannot be loaded on this camera. It may not be possible to load camera settings files that were saved by a camera with a different firmware version.
Page 807 Loading Camera Settings In step 2, select [Load from card] to display up to ten camera settings files on the card. Select a file, and the camera will load it and apply the state of the settings as saved.
Page 808: Custom Shooting Mode (C1-C3)
Custom Shooting Mode (C1–C3) Automatic Update of Registered Settings Canceling Registered Custom Shooting Modes You can register current camera settings such as shooting, menu, and Custom Function settings as Custom shooting modes assigned to < > to < > modes. You can register different functions to use when shooting still photos or movies.
Page 809 Register the desired items. Select the Custom shooting mode to register, then select [OK] on the [Register settings] screen. The current camera settings are registered to Custom shooting mode Automatic Update of Registered Settings If you change a setting while shooting in Custom shooting mode, the mode can be automatically updated with the new setting (Auto update).
Page 810 Canceling Registered Custom Shooting Modes If you select [Clear settings] in step 2, the settings of each mode can be restored to default settings, as they were before registration. Note You can also change shooting and menu settings in Custom shooting modes.
Page 811: Resetting Camera
Resetting Camera The camera's settings for shooting functions and menu functions can be restored to their defaults. Select [ : Reset camera]. Select an item. Reset individual settings Settings for individual selected items can be reset. Factory reset Resets all settings to defaults. Clear the settings.
Page 812 Note For details on clearing all Custom Function settings, see Clear all Custom Func. (C.Fn). For details on clearing Custom Controls settings, see Custom Controls. Still photo Custom shooting modes are reset when [Custom shooting mode (C1- C3)] in [Reset individual settings] is selected in still photo shooting mode, and movie Custom shooting modes are reset when this option is selected in movie recording mode.
Page 813: Copyright Information
Copyright Information Checking the Copyright Information Deleting the Copyright Information When you set the copyright information, it will be recorded to the image as Exif information. Caution If the entry for “Author” or “Copyright” is long, it may not be displayed entirely when you select [Display copyright info.].
Page 814 Enter text. Use the < > or < > dial to select a character, then press < > to enter it. By selecting [ ], you can change the input mode. To delete single characters, select [ ] or press the < >...
Page 815 Deleting the Copyright Information When you select [Delete copyright information] in step 2, you can delete the [Author] and [Copyright] information.
Page 816: System Status Display
You can also check the status log for past errors. Checking camera status with this feature and requesting any required maintenance at a Canon Service Center can reduce camera problems. Checking the Error Log You can check a record of past errors, as well as lens, flash, and battery usage at the time of occurrence.
Page 817 Check the details as needed. Note The camera status log screen lists the five most recent error records. If more than five records are logged, the oldest record is deleted automatically. Shutter-release cycles are indicated in units of 1,000. Check the log as needed. On the screen in step 2, press the <...
Page 818 Check the details as needed. Turn the < > dial to select an item, then press the < > button to view error details. Turn the < > dial to check details.
Page 819 Clearing the Camera Status Log To clear all log information displayed, press the < > button in step 3.
Page 820: Other Information
Other Information Manual/software URL To download instruction manuals, select [ : Manual/software URL] and scan the displayed QR code with a smartphone. You can also use a computer to access the website at the URL displayed and download software. Certification Logo Display Select [ : Certification Logo Display] to display some of the logos of the camera's certifications.
Page 821: Custom Functions/My Menu
Custom Functions/My Menu You can fine-tune camera functions and change the functionality of buttons and dials to suit your shooting preferences. You can also add menu items and Custom Functions that you adjust frequently to My Menu tabs. • Tab Menus: Customization •...
Page 822: Tab Menus: Customization
Tab Menus: Customization : Setting disabled (do not work) Viewfinder Shooting LV Shooting Movie Recording Exposure level increments ○ ○ ○ ISO speed setting increments ○ ○ mode Bracketing auto cancel ○ ○ Bracketing sequence ○ ○ Number of bracketed shots ○...
Page 828: Custom Function Setting Items
Custom Function Setting Items C.Fn1 C.Fn2 C.Fn3 C.Fn4 C.Fn5 C.Fn6 C.Fn7 C.Fn8 C.Fn9 You can customize camera features on the [ ] tab to suit your shooting preferences. Any settings you change from default values are displayed in blue.
Page 829 C.Fn1 Exposure level increments 1/3: ⅓-stop, Exp comp ⅓-stop Sets 1/3-stop increments for the shutter speed, aperture value, exposure compensation amount, AEB range, and flash exposure compensation amount. 1/1: 1-stop, Exp comp ⅓-stop Sets whole-stop increments for the shutter speed and aperture value, and 1/3-stop increments for the exposure compensation amount, AEB range, and flash exposure compensation amount.
Page 830 Bracketing auto cancel You can specify to cancel AEB and white balance bracketing when the power switch is set to < >. ON: Enable OFF: Disable Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0–+: 0, -, + –0+: -, 0, + +0–: +, 0, -...
Page 831 Number of bracketed shots The number of shots taken with AEB and white balance bracketing can be changed. When [Bracketing sequence] is set to [0, -, +], the bracketed shots will be taken as shown in the following table. 3: 3 shots 2: 2 shots 5: 5 shots 7: 7 shots...
Page 832 C.Fn2 Safety shift If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually selected setting to obtain the standard exposure. [Shutter speed/Aperture] applies to < > or < >...
Page 833 Same expo. for new aperture The maximum aperture value may decrease (the lowest f/number may increase) in < > mode (manual exposure shooting) with ISO speed set manually (except when set to ISO Auto) if you (1) Change lenses, (2) Attach an extender, or (3) Use a zoom lens with a variable maximum aperture value.
Page 834 AE lock meter. mode after focus For each metering mode, you can specify whether to lock the exposure (AE lock) once subjects are in focus with One-Shot AF. The exposure will be locked while you keep pressing the shutter button halfway. Select metering modes for AE lock and add a checkmark [ ].
Page 835 C.Fn3 Restrict shooting modes You can restrict the shooting modes available with the < > button. Select shooting modes (< >), then press < > to add a checkmark < >. Select [OK] to register the setting. Caution Restricted shooting mode settings are not registered to < >, <...
Page 836 Set shutter speed range You can set the shutter speed range. In < > or < > mode, you can set the shutter speed manually within your specified range. In < > or < > mode, the shutter speed is set automatically within your specified range (except for movie recording).
Page 837 AE Microadjustment Caution Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent you from obtaining suitable exposure. You can fine-tune the standard exposure level. Effective if images in autoexposure shooting without exposure compensation usually seem underexposed or overexposed.
Page 838 FE Microadjustment Caution Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent you from obtaining suitable flash exposure. You can fine-tune the standard flash exposure level. Effective if main subjects in autoflash shooting without flash exposure compensation usually seem underexposed or overexposed.
Page 839 C.Fn4 Continuous shooting speed You can set the continuous shooting speed for < > high-speed continuous shooting, < > medium-speed continuous shooting, < > low-speed continuous shooting, < > soft continuous shooting, and < > soft low-speed continuous shooting. Select [OK] to register the setting. High speed The default setting is 16 shots/sec.
Page 840 Restrict drive modes You can restrict the drive modes available with the < > button. Select drive modes (< >), then press < > to add a checkmark < >. Select [OK] to register the setting. Caution The < > mark cannot be cleared from all modes at the same time.
Page 841 C.Fn5 Viewfinder info. during exp. For viewfinder shooting, you can set whether to display shooting information in the viewfinder during exposure. OFF: Disable ON: Enable Shooting information remains displayed in the viewfinder during exposure. Useful when you want to check exposure, number of shots available, and other information during continuous shooting.
Page 842 Rec card, img size setting As the display used when the < > button is pressed to select a card or set the image size, you can specify the rear LCD panel or the screen. : Rear LCD panel After pressing the < >...
Page 843 C.Fn6 Warnings in viewfinder The < > icon can be displayed in the field of view of the viewfinder when any of the following functions are set ( ). Select the function for which you want the warning icon to appear, then press <...
Page 844 Multi function lock With the power switch set to < >, this function can prevent settings from being changed by accidentally touching < >, < >, < >, < >, or the touch-screen panel. Select the camera controls to lock by setting the switch to < >, then press <...
Page 845 / button function You can change the function of the < > button. During image playback, you can protect images, record voice memos, and rate images. / : Protect(Hold:Record memo) To protect an image, press the < > button. To start recording a voice memo, hold down the <...
Page 846 C.Fn7 switching ( : Enable : Disable When set to [Disable ], setting the Live View shooting/Movie shooting switch to < > does not enable movie recording. This enables still photo shooting at all times. Smart controller Enables you to move AF points by dragging on the smart controller after pressing the <...
Page 847 Add cropping information Adding cropping information displays vertical lines for the aspect ratio specified in Live View shooting, so that you can compose shots as if shooting with a medium- or large-format camera (6×6 cm, 4×5 inch, and so on). When you shoot, instead of cropping images recorded to the card, the camera adds aspect ratio information to images for cropping in the Digital Photo Professional (EOS software).
Page 848 Timer duration You can change how long a function setting associated with a button remains in effect after you release the button. Can be set in a range of 0–59 sec. or 1–60 min. 6 sec. timer You can set how long to continue metering and AE lock. 16 sec.
Page 849 Audio compression Sets audio compression for movie recording. [Disable] allows higher audio quality than when audio is compressed, but file sizes are larger. ON: Enable OFF: Disable Caution Editing movie files recorded with [Disable] and then saving them with compression will also compress the audio.
Page 850 C.Fn8 Default Erase option You can set which option is selected by default in the erase menu ( ), which is accessed by pressing the < > button during image playback or during review after shooting. By setting an option other than [Cancel], you can simply press < >...
Page 851 Add IPTC information Registering IPTC (International Press Telecommunications Council) information to the camera from the EOS application EOS Utility enables you to record (add) this information to JPEG/HEIF/RAW still photos at the time of shooting. This is helpful in file management and other tasks using the IPTC information.
Page 852 C.Fn9 Clear all Custom Func. (C.Fn) Selecting [ 9: Clear all Custom Func. (C.Fn)] clears all Custom Function settings. Note Customized operations for [ 6: Custom Controls], [ switching ( )], and [ Smart controller] are not cleared if you perform [ 9: Clear all Custom Func.
Page 853: Custom Controls
Custom Controls : Metering and AF Start : Switch to Registered AF Function : Switch to Registered AF Point : Direct AF Point Selection : Select AF Point, During Met) : Set ISO, During Met) : Image Size Selection : One-Touch Image Quality Setting : One-Touch Image Quality (Hold) : Register/Recall Shooting Function : Unlock While Button Pressed...
Page 854 Select a part of the bar. Select a function to assign. Press < > to set it. You can configure advanced settings for functions labeled with in the lower left of the screen by pressing the < > button. Note Default settings can be restored by pressing the <...
Page 855 Functions available for camera controls Function ○ ○ ○ ○ Metering and AF start ○ ○ ○ ○ ○ AF stop ○ ○ ○ Switch to registered AF function ○ ○ ○ ○ ○ ONE SHOT AI SERVO ○ ○ ○...
Page 856 Exposure Function ○ ○ ○ Metering start ○ ○ ○ ○ ○ ○ AE lock ○ AE lock (while button pressed) ○ ○ ○ ○ ○ ○ AE lock (hold) ○ ○ AE lock, AF stop ○ ○ ○ ○ ○...
Page 857 ○ ○ Shutter speed setting in M mode ○ ○ Aperture setting in M mode Movies Function ○ ○ ○ Pause Movie Servo AF Start movie ○ ○ ○ ○ recording (when set) Image Function ○ Image size selection ○ ○...
Page 858 Operation Function ○ ○ Depth-of-field preview ○ ○ ○ IS start ○ Menu display ○ ○ Register/recall shooting function ○ ○ Unlock while button pressed ○ Switch to Custom shooting mode ○ Image replay Magnify/Reduce ○ (press , turn ○ ○...
Page 859 ○ Cycle between the set functions ○ Flash function settings ○ ○ ○ ○ Flash firing ○ ○ ○ ○ Illuminate info in viewfinder ○ ○ ○ ○ Network settings ○ ○ ○ ○ Create folder ○ ○ ○ ○ ○...
Page 861 AF area selection mode ( Pressing the < > or < > button starts AF in your specified AF area selection mode. To continue using the current AF point when you press the < > or < > button, set [AF start position] to [Manually selected AF point], and to continue using the current AI Servo AF characteristics, AF operation, and AF area selection mode, select [Maintain current setting].
Page 868 : One-Touch Image Quality Setting Pressing the button assigned to this function enables you to switch to the image size set here. While the camera switches the image size, icons blink in the viewfinder and the image size blinks on the rear LCD panel. One-touch image quality setting is canceled after you finish shooting, and the camera reverts to the original image size.
Page 869 : One-Touch Image Quality (Hold) Pressing the button assigned to this function enables you to switch to the image size set here. While the camera switches the image size, icons blink in the viewfinder and the image size blinks on the rear LCD panel. One-touch image quality setting is not canceled after you shoot.
Page 871 : Unlock While Button Pressed Even with the power switch set to < >, by holding down the button assigned to this function, you can use camera controls that are locked by [ 6: Multi function lock].
Page 873 : Cycle Between the Set Functions Each press of the < > button switches from one shooting function setting to the next. * 9: To access the detailed settings screen when the setting screen is displayed, press the < > button.
Page 874 : Illuminate Info in Viewfinder By pressing the button assigned to this function, you can activate red illumination for information in the viewfinder. To deactivate the illumination, either press the button assigned to this function again or a button that starts the metering timer, such as the shutter button. Caution Pressing the button assigned to this function during AE lock cancels AE lock and illuminates information in the viewfinder.
Page 875: Tab Menus: My Menu
Tab Menus: My Menu Add My Menu tab Delete all My Menu tabs Delete all items Menu display...
Page 876: Registering My Menu
Registering My Menu Creating and Adding My Menu Tabs Registering Menu Items under the My Menu Tab(s) My Menu Tab Settings Deleting All My Menu Tabs/Deleting All Items Menu Display Settings On the My Menu tab, you can register menu items and Custom Functions you often adjust.
Page 877 Creating and Adding My Menu Tabs Select [Add My Menu tab]. Select [OK]. You can create up to five My Menu tabs by repeating steps 1 and 2.
Page 878 Registering Menu Items under the My Menu Tab(s) Select [MY MENU*: Configure]. Select [Select items to register]. Register the desired items. Select an item, then press < >. Select [OK] on the confirmation screen. You can register up to six items. To return to the screen in step 2, press the <...
Page 879 My Menu Tab Settings You can sort and delete items on the menu tab, and rename or delete the menu tab itself. Sort registered items You can change the order of the registered items in My Menu. Select [Sort registered items], select an item to rearrange, then press <...
Page 880 Rename tab You can rename the My Menu tab from [MY MENU*]. Select [Rename tab]. Enter text. To delete single characters, select [ ] or press the < > button. Use the < > or < > dial to select a character, then press <...
Page 881 Deleting All My Menu Tabs/Deleting All Items You can delete all the created My Menu tabs or My Menu items registered on them. Delete all My Menu tabs You can delete all My Menu tabs you created. When you select [Delete all My Menu tabs], all the tabs from [MY MENU1] to [MY MENU5] will be deleted and the [ ] tab will revert to its default.
Page 882 Menu Display Settings You can select [Menu display] to set the menu screen that is to appear first when you press the < > button. Normal display Displays the last displayed menu screen. Display from My Menu tab Displays with the [ ] tab selected.
Page 883: Reference
Reference This chapter provides reference information on camera features. • Importing Images to a Computer • Troubleshooting Guide • Error Codes • Compatible Lenses and Autofocusing (Viewfinder Shooting) • System Map • Performance Data • Information Display • Specifications...
Page 884: Importing Images To A Computer
Importing Images to a Computer Connecting to a Computer with an Interface Cable Using a Card Reader Connecting to a Computer via Wi-Fi You can use EOS software to import images from the camera to a computer. There are three ways to do this. Connecting to a Computer with an Interface Cable Install EOS Utility ( Connect the camera to the computer.
Page 885 Caution With a Wi-Fi connection established, the camera cannot communicate with the computer even if they are connected with an interface cable. Note By connecting to an FTP server, you can send images on the camera to a computer (...
Page 886 Using a Card Reader You can use a card reader to import images to a computer. Install Digital Photo Professional ( Insert the card into the card reader. Use Digital Photo Professional to import the images. Refer to the Digital Photo Professional Instruction Manual. Note When downloading images from the camera to a computer with a card reader without using EOS software, copy the DCIM folder on the card to the computer.
Page 887 Connecting to a Computer via Wi-Fi You can connect the camera to the computer via Wi-Fi and import images to the computer...
Page 888: Troubleshooting Guide
Sensor cleaning problems Computer connection problems If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-related problems The battery does not charge.
Page 889 [Battery communication error. Does this battery/do these batteries display the Canon logo?] is displayed. Do not use any battery packs other than a genuine Canon Battery Pack LP-E19. Remove and install the battery again ( If the electrical contacts are dirty, use a soft cloth to clean them.
Page 890 Shooting-related problems The lens cannot be attached. The camera cannot be used with RF, EF-S, or EF-M lenses ( The viewfinder is dark. Install a charged battery in the camera ( No images can be shot or recorded. Make sure the card is properly inserted ( If the card is full, replace the card or delete unnecessary images to make space Shooting is not possible during One-Shot AF when the focus indicator <...
Page 891 The maximum burst shown in the table in Performance Data is based on the standard Canon test card, so the faster the card's writing speed, the higher the actual maximum burst will be. For this reason, estimated maximum burst as indicated in the viewfinder may differ from actual maximum burst.
Page 892 Expanded ISO speeds cannot be selected for still photo shooting. Check the [ISO speed range] setting under [ ISO speed settings]. Expanded ISO speeds are not available when [ : Highlight tone priority] is set to [Enable] or [Enhanced]. Expanded ISO speeds are not available when [ : HDR shooting ] is set to [Enable].
Page 893 The flash does not fire. Make sure the flash unit (or sync cord) is securely attached to the camera. When using flash in Live View shooting, set [ : Shutter mode] to an option other than [Electronic] ( The flash always fires at full output. Flash units other than EL/EX series Speedlites used in autoflash mode always fire at full output ( When the flash Custom Function setting for [Flash metering mode] is set to [TTL flash...
Page 894 Movie recording stops by itself. If the card's writing speed is slow, movie recording may stop automatically. For cards that can record movies, see Performance Data. To find out the card's writing speed, refer to the card manufacturer's website, etc. Perform low-level formatting to initialize the card if the card's writing or reading speed seems slow ( Recording stops automatically once your movie reaches 29 min.
Page 895 Sound is not recorded in movies. Sound is not recorded in High Frame Rate movies. A time code is not added. Time codes are not added when you record High Frame Rate movies with [Count up] in : Time code] set to [Free run] ( ).
Page 896 Problems with wireless features Cannot pair with a smartphone. Use a smartphone compliant with Bluetooth Specification Version 4.1 or later. Turn on Bluetooth from the smartphone settings screen. Pairing with the camera is not possible from the smartphone's Bluetooth settings screen. Install the dedicated app Camera Connect (free of charge) on the smartphone ( Pairing with a previously paired smartphone is not possible if pairing information registered for another camera remains on the smartphone.
Page 897 Operation problems Settings change when I switch from still photo shooting to movie recording or vice versa. Separate settings are retained for use when shooting still photos and recording movies. I cannot change the setting with < >, < >, < >, <...
Page 898 Display problems The display starts with [ ] My Menu, or the [ ] tab alone is displayed. [Menu display] on the [ ] tab is set to [Display from My Menu tab] or [Display only My Menu tab]. Set [Normal display] ( The file name's first character is an underscore (“_”).
Page 899 Playback problems Part of the image blinks in black. : Highlight alert] is set to [Enable] ( A red box is displayed on the image. : AF point disp.] is set to [Enable] ( During image playback, the AF points are not displayed. AF points are not displayed in playback of cropped images.
Page 900 The movie appears to freeze momentarily. Significant change in the exposure level during Program AE recording may cause recording to stop momentarily until the brightness stabilizes. In such a case, shoot in the < > mode ( The movie is played in slow motion. High Frame Rate movies are recorded at 29.97 fps or 25.00 fps, so they are played in slow motion at 1/4 speed.
Page 901 Sensor cleaning problems The shutter makes a sound during sensor cleaning. Although there is a mechanical sound from the shutter during cleaning after [Clean now ] is selected, no image is recorded to the card ( Automatic sensor cleaning does not work. If you repeatedly turn the power switch <...
Page 902 Computer connection problems I cannot import images to a computer. Install EOS Utility (EOS software) on the computer ( Make sure the main EOS Utility window is displayed. If the camera is already connected via Wi-Fi, it cannot communicate with any computer connected with an interface cable.
Page 903: Error Codes
Error Codes (1) Error number (2) Cause and countermeasures If there is a problem with the camera, an error message will appear. Follow the on-screen instructions. If the problem persists, write down the error code (Errxx) and request service.
Page 904: Compatible Lenses And Autofocusing (Viewfinder Shooting)
] points remain lit). For details on AF point blinking/illumination, see Meaning of Lit or Blinking AF Points. For updates on “Group Classification of Lenses,” visit the Canon website or others. Some lenses may not be available in certain countries or regions.
Page 905 Group A Autofocusing with 191 points is possible. All the AF area selection modes are available. : Dual cross-type AF point. Offers superior subject tracking and higher focusing precision than other AF points. : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines.
Page 906 Group B Autofocusing with 191 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines.
Page 907 Group C Autofocusing with 191 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Offers superior subject tracking and higher focusing precision than other AF points. : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines.
Page 908 Group D Autofocusing with 191 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines.
Page 909 Group E Autofocusing with 191 points is possible. All the AF area selection modes are selectable. With an extender attached to extendable lenses, AF is available when maximum aperture is f/8 (in a range of f/5.6–f/8). : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines.
Page 910 Group F Not all 191 AF points can be used for autofocusing, but the 139 points shown here are available. All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 191- point Automatic selection AF.
Page 911 Group G Not all 191 AF points can be used for autofocusing, but the 87 points shown here are available. All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 191- point Automatic selection AF.
Page 912 Group H The 23 AF points shown here are available for autofocusing. As the AF area selection mode, choose from Spot AF, 1-point AF, Expand AF area: , Zone AF (manual selection), or 23- point Automatic selection AF. With an extender attached to extendable lenses, AF is available when maximum aperture is f/8 (in a range of f/5.6–f/8).
Page 913 Group I The 15 AF points shown here are available for autofocusing. As the AF area selection mode, choose from Spot AF, 1-point AF, Expand AF area: , or 15-point Automatic selection AF. With an extender attached to extendable lenses, AF is available when maximum aperture is f/8 (in a range of f/5.6–f/8).
Page 914 Group J The 9 AF points shown here are available for autofocusing. As the AF area selection mode, choose from Spot AF, 1-point AF, or Expand AF area: : Cross-type AF point. Offers excellent subject tracking and high-precision focusing. : AF points sensitive to horizontal lines (AF points to the left and right of the center) or vertical lines (AF points above and below the center).
Page 915 Group Classification of Lenses EF 14mm f/2.8 L USM EF 14mm f/2.8 L II USM EF 15mm f/2.8 Fisheye EF 20mm f/2.8 USM EF 24mm f/1.4 L USM EF 24mm f/1.4 L II USM EF 24mm f/2.8 EF 24mm f/2.8 IS USM EF 28mm f/1.8 USM EF 28mm f/2.8 EF 28mm f/2.8 IS USM...
Page 916 EF 135mm f/2 L USM EF 135mm f/2 L USM + Extender EF 1.4x I/II/III EF 135mm f/2 L USM + Extender EF 2x I/II/III EF 135mm f/2.8 (Softfocus) EF 180mm f/3.5 L Macro USM EF 180mm f/3.5 L Macro USM + Extender EF 1.4x I/II/III EF 200mm f/1.8 L USM EF 200mm f/1.8 L USM + Extender EF 1.4x I/II/III EF 200mm f/1.8 L USM + Extender EF 2x I/II/III...
Page 917 EF 400mm f/2.8 L USM EF 400mm f/2.8 L USM + Extender EF 1.4x I/II/III EF 400mm f/2.8 L USM + Extender EF 2x I/II/III EF 400mm f/2.8 L II USM EF 400mm f/2.8 L II USM + Extender EF 1.4x I/II/III EF 400mm f/2.8 L II USM + Extender EF 2x I/II/III EF 400mm f/2.8 L IS USM EF 400mm f/2.8 L IS USM + Extender EF 1.4x I/II/III...
Page 918 EF 600mm f/4 L USM EF 600mm f/4 L USM + Extender EF 1.4x I/II/III EF 600mm f/4 L USM + Extender EF 2x I/II I (f/8)* EF 600mm f/4 L USM + Extender EF 2x III E (f/8)* EF 600mm f/4 L IS USM EF 600mm f/4 L IS USM + Extender EF 1.4x I/II/III EF 600mm f/4 L IS USM + Extender EF 2x I/II I (f/8)
Page 919 EF 28-70mm f/2.8 L USM EF 28-70mm f/3.5-4.5 EF 28-70mm f/3.5-4.5 II EF 28-80mm f/2.8-4 L USM EF 28-80mm f/3.5-5.6 EF 28-80mm f/3.5-5.6 USM EF 28-80mm f/3.5-5.6 II EF 28-80mm f/3.5-5.6 II USM EF 28-80mm f/3.5-5.6 III USM EF 28-80mm f/3.5-5.6 IV USM EF 28-80mm f/3.5-5.6 V USM EF 28-90mm f/4-5.6 EF 28-90mm f/4-5.6 USM...
Page 920 EF 50-200mm f/3.5-4.5 EF 50-200mm f/3.5-4.5 L EF 55-200mm f/4.5-5.6 USM EF 55-200mm f/4.5-5.6 II USM EF 70-200mm f/2.8 L USM EF 70-200mm f/2.8 L USM + Extender EF 1.4x I/II/III EF 70-200mm f/2.8 L USM + Extender EF 2x I/II/III EF 70-200mm f/2.8 L IS USM EF 70-200mm f/2.8 L IS USM + Extender EF 1.4x I/II/III EF 70-200mm f/2.8 L IS USM + Extender EF 2x I/II/III...
Page 921 EF 75-300mm f/4-5.6 EF 75-300mm f/4-5.6 USM EF 75-300mm f/4-5.6 II EF 75-300mm f/4-5.6 II USM EF 75-300mm f/4-5.6 III EF 75-300mm f/4-5.6 III USM EF 75-300mm f/4-5.6 IS USM EF 80-200mm f/2.8 L EF 80-200mm f/4.5-5.6 EF 80-200mm f/4.5-5.6 USM EF 80-200mm f/4.5-5.6 II EF 90-300mm f/4.5-5.6 EF 90-300mm f/4.5-5.6 USM...
Page 922 Caution AF is not available with Extender EF 2x (I/II/III) attached to the EF 180mm f/3.5 L Macro USM lens. Precise autofocusing may not be achieved if you use a lens and Extender EF1.4x III/EF2x III combination marked with an asterisk or a lens and extender in a combination marked with two asterisks.
Page 923: System Map
System Map (10) (11) (12) (13) (14) (15) (16) (17) (21) (32) (18) (38) (27) (22) (19) (33) (28) (34) (29) (35) (25) (36) (20) (37) (39) (26) (30) (31) (23) (24) : Bundled accessories Speedlite Transmitter ST-E2 Speedlite Transmitter ST-E3-RT Speedlite 270EX II Speedlite EL-100 Speedlite 430EX III-RT/430EX III...
Page 924 (21) Eyecup Eg (22) Strap (23) AC Adapter AC-E19 (24) DC Coupler DR-E19 (25) Battery Pack LP-E19 (26) Battery Charger LC-E19 (27) Cable protector *2, *3 (28) Interface Cable IFC-100U (approx. 1 m/3.3 ft.) *2, *4 (29) Interface Cable IFC-400U (approx. 4m/13.1 ft.) (30) CFexpress card (31)
Page 925: Performance Data
* 3: ISO 1600 for lenses that do not support variable control of maximum ISO Auto limit for E-TTL. For details, refer to the Canon website. * 4: Changed to the value nearest ISO 400 if out of the setting range.
Page 926 20 M • Number of shots available and maximum burst as measured in viewfinder shooting with a 325 GB card conforming to Canon testing standards. • Varies depending on shooting conditions (such as when JPEG/HEIF image quality is set to 8, as well as the subject, memory card brand, ISO speed, Picture Style, and Custom...
Page 927 Movie Recording Total movie recording time and file size per minute (Approx.) Total Available Recording Time on Card File Size Movie Recording Size (Approx. ** MB/min.) 64 GB 256 GB 1 TB 3 min. 13 min. 50 min. 18711 4 min. 18 min.
Page 928 Total possible time for movie recording (Approx.) Temperature Room Temperature (+23°C / 73°F) Low Temperature (0°C / 32°F) 4 hr. 40 min. 4 hr. 10 min. • With a fully charged Battery Pack LP-E19. • With [Movie Servo AF] set to [Disable]. •...
Page 929 ). The maximum limit is not expanded, even when expansion is set in [Max for Auto]. The minimum speed in the automatic setting range is ISO 400 when [ : Canon Log settings] is set to [On] ( In <...
Page 930 Image Playback Resize options, by original JPEG image quality Available Resize Settings Original Image Quality ○ ○ ○ ○ ○ ○...
Page 931: Information Display
Information Display Quick Control Screen (in Viewfinder Shooting) Button Operations on the Quick Control/Custom Quick Control Screen Live View Shooting Screen Movie Recording Screen Playback Screen Quick Control Screen (in Viewfinder Shooting) (15) (16) (17) (18) (19) (20) (21) (10) (11) (22) (12)
Page 932 Exposure compensation Aperture value White balance correction White balance Shutter speed Shooting mode Picture Style Auto Lighting Optimizer AF operation (10) Quick Control icon (11) Battery level (12) Mirror lockup (13) Flash ready/FE lock/High-speed sync (14) Metering mode (15) AE lock (16) Highlight tone priority (17)
Page 933 Button Operations on the Quick Control/Custom Quick Control Screen Press the < > / < > / < > / < > / < > / < > / < > buttons to access the corresponding setting screen, then use < >...
Page 934 Metering mode/flash exposure compensation AF point selection ISO speed Exposure compensation...
Page 935 White balance AEB setting...
Page 936 Live View Shooting Screen Each time you press the < > button, the information display will change. The display will show only the settings currently applied. (10) (11) (12) (13) (14) (15) (16) (17) (18) Maximum burst Available shots/Sec. until self-timer shoots Multiple exposures Shooting mode AF method...
Page 937 (19) (20) (28) (29) (21) (22) (30) (31) (23) (32) (24) (25) (33) (26) (34) (27) (35) (36) (19) GPS acquisition status (20) AEB/FEB (21) View Assist (22) HDR PQ (23) Flash ready/FE lock/High-speed sync (24) Electronic shutter (25) AE lock (26) Shutter speed/Multi-function lock warning (27)
Page 938 Movie Recording Screen Each time you press the < > button, the information display will change. The display will show only the settings currently applied. (11) (12) (13) (14) (15) (16) (17) (18) (19) (10) Temperature warning Battery level Time available per recording/Elapsed recording time Movie recording mode/High Frame Rate movie AF method Movie recording size...
Page 939 (20) (27) (21) (28) (22) (29) (23) (24) (30) (31) (20) Audio recording level indicator (manual/line input) (21) Canon Log (22) AE lock (23) Shutter speed (24) Aperture value (25) Wi-Fi function (26) Wi-Fi signal strength (27) Bluetooth function (28)
Page 940 Playback Screen Basic information display for still photos (10) (11) (12) (13) (14) (15) (16) (17) (18) HDR output status/View Assist Bluetooth function Wi-Fi signal strength Wi-Fi function Battery level Current image no./Total images/No. of images found Shutter speed Aperture value Exposure compensation amount (10) Already sent to a computer/smartphone...
Page 941 Caution If the image was taken by another camera, certain shooting information may not be displayed. It may not be possible to play back images taken with this camera on other cameras.
Page 942 Detailed information display for still photos (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (10) Aperture value Picture Style/Settings Shutter speed WB correction/Bracketing Shooting mode/Multiple exposure/Frame Grab White balance Auto Lighting Optimizer AE Microadjustment FE Microadjustment (10) AF Microadjustment (11) Exposure compensation amount (12)
Page 943 Detailed information display for movies Movie playback Movie recording mode/High Frame Rate Image size Frame rate Compression method Movie digital IS Recording time Movie recording format * For simplicity, explanations are omitted for items that are also included in basic/detailed information display for still photos, which are not shown here.
Page 944: Specifications
Recording media * Type B compatible: 2 card slots Image sensor size Approx. 35.9×23.9 mm Canon EF lens product groups Compatible lenses * Excluding EF-S and EF-M lenses (Effective angle of view is approx. equivalent to the indicated focal length.)
Page 945 Recording system Recording format DCF 2.0 JPEG (8-bit), HEIF (10-bit), RAW (14-bit Canon original) RAW+JPEG simultaneous recording possible Image type RAW+HEIF simultaneous recording possible * 12 bit A/D conversion processing is applied for RAW images shot with the electronic shutter.
Page 946 Image processing during shooting Auto, Standard, Portrait, Landscape, Fine Detail, Neutral, Faithful, Monochrome, Picture Style User Defined 1–3 Auto (Ambience priority), Auto (White priority), Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom (5 settings), Color White balance temperature setting (approx.
Page 947 Autofocus (viewfinder shooting) TTL secondary image-registration, phase-difference detection with the Focus method dedicated AF sensor 191 points max. (cross-type AF points: 155 points max.) * Number of available AF points, Dual cross-type AF points, and Cross-type AF points AF points vary depending on the lens used.
Page 948 Autofocus (Live View shooting/Movie recording) Focus method Dual Pixel CMOS AF Face+Tracking, Spot AF, 1-point AF, Expand AF area (vertically/horizontally), AF method Expand AF area: Around, Zone AF, Large Zone AF: Vertical, Large Zone AF: Horizontal Max. 3869 Available AF point positions * When selected with the Multi-controller Available AF areas when Max.
Page 949 Exposure control Viewfinder shooting: 216-zone (18×12) TTL open-aperture metering with an approx. 400,000-pixel RGB+IR metering sensor Metering mode Live View shooting/movie recording: 384-zone (24×16) metering with signals from the image sensor Viewfinder shooting: Evaluative metering Partial metering (approx. 6.2% of screen) Spot metering (approx.
Page 950 Multiple exposures Shooting method Function/control priority, Continuous shooting priority Number of multiple exposures 2 to 9 exposures Multiple-exposure control Additive, Average, Bright, Dark HDR shooting (still photo HDR PQ) Recording format HEIF Bit depth 10-bit Color sampling YCbCr 4:2:2 HDR specification ITU-R BT.2100 (PQ) Shutter Type...
Page 951 Maximum burst RAW+HEIF Large: approx. 350 shots * In viewfinder shooting with a 325 GB card conforming to Canon testing standards * Varies depending on shooting conditions (such as when JPEG/HEIF image quality is set to 8, as well as the subject, memory card brand, ISO speed, Picture Style, and...
Page 952 ±3 stops in 1/3- or 1/2-stop increments FE lock Available PC terminal Available Flash control Flash function settings, Flash Custom Function settings Movie recording Canon Log Recording format Compression MPEG-4 H.264/AVC MPEG-4 H.265/HEVC Video signal recording range Full range (0–255) Full range (128–1016)
Page 953 Sound-recording level adjustable, wind filter provided, attenuator provided Headphone Headphone terminal provided, volume adjustable Movie Digital IS Available Canon Log Available as a shooting option Still photo shooting Not available during movie recording Image output without information display available HDMI output...
Page 954 Screen Type TFT color, liquid-crystal monitor Screen size and dots Approx. 8.01 cm (3.15 in.) (3:2) with approx. 2.1 million dots Brightness adjustment Manual (7 levels) Color tone adjustment Warm tone, Standard, Cool tone 1, Cool tone 2 Interface languages Touch-screen panel Capacitive sensing System status display...
Page 955 Playback Without shooting information, with basic information, with detailed shooting Image display format information, index display (4/9/36/100 images) Highlight alert Overexposed highlights blink AF point display Available (except under certain shooting conditions) Grid display 3 types Magnified view Approx. 1.5×–10×, initial magnification and position settable Image search Search conditions settable (by rating, date, folder, protected, type of file) 1 image, 10 images, Specified number, Date, Folder, Movies, Stills, Protect,...
Page 956 Smartphone, computer, FTP server [Wired LAN] Type Ethernet Standards compliance IEEE 802.3u (10BASE-T/100BASE-TX/1000BASE-T) Access point, computer, EOS-1D X Mark III* Compatible devices * When syncing time between cameras [Bluetooth] Bluetooth Specification Version 4.2 compliant Standards compliance (Bluetooth low energy technology)
Page 957 Customization features Custom Functions 38 functions Custom Quick Control Available Saving camera settings Up to 10 settings can be registered on a card Custom shooting modes Still photo C1/C2/C3 modes, movie C1/C2/C3 modes My Menu Up to 5 screens can be registered Copyright information Text entry and appending possible IPTC information...
Page 958 Dimensions and weight listed above are based on CIPA Guidelines (except weight for camera body only). Product specifications and appearance are subject to change without notice. If a problem occurs with a non-Canon lens attached to the camera, contact the respective lens manufacturer.
Page 959: Trademarks And Licensing
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Canon Inc. is under license. Other trademarks and trade names are those of their respective owners. All other trademarks are the property of their respective owners.
Page 960 About MPEG-4 Licensing “This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video.
Page 961 This product is designed to achieve optimum performance when used with genuine Canon accessories. Therefore, using this product with genuine accessories is highly recommended. Canon shall not be liable for any damage to this product and/or accidents such as malfunction, fire, etc. caused by the failure of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery).

Canon EOS-1D X Mark III Advanced User's Manual

Introduction

Preparation and Basic Operations

Shooting Mode

Shooting and Recording

Af/Drive

Playback

Communication Functions

Set-Up

Custom Functions/My Menu

Reference

Trademarks and Licensing

Quick Links

Troubleshooting

Related Manuals for Canon EOS-1D X Mark III

Summary of Contents for Canon EOS-1D X Mark III