Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Network Card
  5. NPB-ZWAVE
  6. Installation instructions

Honeywell NPB-ZWAVE Installation Instructions

Option card
Hide thumbs
1
2
3
4

Advertisement

Quick Links

Download this manual
NPB-ZWAVE Option Card
This document covers the mounting of a NPB-ZWAVE option
®
®
card in a Tridium
JACE
controller, including models WEB/
CP-600, WEB/CP/700, WEB/CP/602-XPR, or WEB/CP
controllers.
Table 1. NPB-ZWAVE option description.
Description
Z-Wave wireless option
card for serial gateway
support between the
hosted WEBStation-AX
or Comfort Point
Workbench and an RF
wireless Z-Wave domain.
This option card allows
NiagaraAX integration of
wireless Z-Wave
devices.
An RP-SMA coax stub
antenna is included.
Four status LEDs are on
the option card's top
surface.
NOTE: The WEB/CP Controller requires NiagaraAX-3.5 or
later to support operation of the NPB-ZWAVE.
Models /Notes
NPB-ZWAVE - For domestic
U.S. usage.
908.42 MHz frequency
An optional antenna extension
kit allows the included antenna
to be located up to 6.56 feet
(2m) away from the option
card.
This kit is required if installing
in a WEB/CP-202-602
controller model. See "Antenna
Extension Option".
The NPB-ZWAVE option card
adds one COM port on the
JACE controller. See "COM
Port Usage".

INSTALLATION INSTRUCTIONS

Not covered in this document are NiagaraAX Z-Wave driver
(software) topics about using this option card. For all other
related mounting and wiring details, refer to the appropriate
mounting and wiring document. See "Related
Documentation".
INCLUDED IN THIS PACKAGE
Included in this package you should find the following items:
• NPB-ZWAVE option card, with pre-attached endplate.
• an RP-SMA coax-mounted stub antenna.
• This document NPB-ZWAVE Option Card Installation
Instructions, Form Number 69-0349.
TX
STATUS LEDS
RX
SERIAL
Fig. 1. NPB-ZWAVE Option
MATERIAL AND TOOLS
REQUIRED
The following supplies and tools are required:
• #2 phillips screwdriver: used to install the NPB-ZWAVE
option card.
• If installing in a WEB/CP-XPR (WEB/CP-202/602-XPR), an
antenna cable kit. See "Antenna Extension Option". Also, a
#1 phillips screwdriver.
LED1
STATUS LEDS
LED2
SUPPLIED
STUB
ANTENNA
ANTENNA
CONNECTOR
RP-SMA COAX
M32453
Put Bar Code Here
62-0349-01

Advertisement

loading

Related Manuals for Honeywell NPB-ZWAVE

Summary of Contents for Honeywell NPB-ZWAVE

  • Page 1: Installation Instructions

    • This document NPB-ZWAVE Option Card Installation Instructions, Form Number 69-0349. LED1 STATUS LEDS STATUS LEDS LED2 SERIAL This document covers the mounting of a NPB-ZWAVE option ® ® card in a Tridium JACE controller, including models WEB/ SUPPLIED CP-600, WEB/CP/700, WEB/CP/602-XPR, or WEB/CP STUB controllers.
  • Page 2 If a WEB/CP-202/602-XPR series, remove the bat- aligned). tery and bracket assembly by taking out the Mount the NPB-ZWAVE option card in either of the option screws holding it in place, setting screws aside for card slots of the controller, as needed. Note the WEB/CP-202/ later.
  • Page 3 NPB-ZWAVE OPTION CARD 6. Carefully insert the pins of the NPB-ZWAVE into the 10. Replace the controller’s cover. socket of the appropriate option card slot. Mounting If accessory modules were unplugged, plug them back holes on the option board should line up with the stand- into the controller as before, and secure.

  • Page 4: Related Documentation

    The module also complies to EN300220 for ETSI (European For example, if a NPB-ZWAVE card is in Slot 1 of WEB/CP- FCC) approval. 201/600 and a NPB-2X-RS485 option card is in Slot 2, the two NPB-2X-RS485 option ports are COM4 and COM5.