Philips CID3683/93 Quick Start Manual

Register your product and get support at
www.philips.com/welcome
Quick Start Guide
ENG
English

Install the car audio

These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult your
Philips car audio dealer.
Caution
• This unit is designed for negative ground
(earth) 12 V DC operation only.
Always install this unit in the car dashboard.
•
Other locations can be dangerous as the
rear of the unit heats up during use.
• To avoid short-circuit: before you connect,
ensure that the ignition is off.
Ensure that you connect the yellow and red
•
power supply leads after all other leads are
connected.
• Ensure that all loose leads are insulated with
electrical tape.
• Ensure that the leads do not get caught
under screws orin parts that will move
(e.g. seat rail).
Ensure that all ground (earth) leads are run
•
to a common ground (earth) point.
• Use only the supplied mounting hardware
for a safe and secure installation.
• Improper fuses can cause damage or fi re.
When you need to change the fuse, consult
a professional.
Note on the power supply lead (yellow)
• When you connect other devices to this
system, ensure that the rating of the car
circuit is higher than the total fuse value of
all the connected devices.
Notes on speaker connection
• Never connect speaker wires to the metal
body or chassis of the car.
• Never connect speaker wires with stripes
to one another.
CID3683
Connect wires
1
Caution
• Ensure that all loose leads are insulated with
electrical tape.
1
Check the car's wiring carefully, then do the
other connections:
Connect GPS antenna 2
To receive signal from satellites, connect the supplied
GPS antenna to your car and the system.
1
Connect the supplied GPS antenna to the
system fi rst.
2
Stick the other end of the GPS antenna to a
surface for better signal reception.
Mount in the dashboard
3
Note
Check wire connection before you mount
•
the unit into a car.
1
Take off the trim plates of the car.
2
Open the glove box before the front
passenger seat.
3
Connect the wires.
4
Replace the screen of the host car audio with
a
the screen of CID3863.
5
Fix the main unit to the mounting brackets
b
with the M2.6 x 5 screws.
6
Fix the mounting brackets to the car with the
c
M5 x 10 screws.
7
Attach the trim plate.
Turn on
Caution
• Risk of road accidents! Never watch video
or adjust settings while you drive.
1
Press and hold to turn on the unit.
1
2
The available OSD (On-Screen Display)
»
languages are displayed.
2
Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
• To turn off the unit, press and hold .

Set date

1
Touch the upper left corner to display main
menu.
2
Touch in the middle right side of the screen.
The second main menu is displayed.
»
3
Touch [Settings] .
4
Touch [Time] .
The date setup menu is displayed.
»
5
Touch on the displayed date information.
6
Touch or to set year, month and day.

Set clock mode

1
Touch [Clock mode].
2
Touch on [12Hr] or [24Hr] to select clock
mode.
Tip
• When date is set, touch fi rst and then
touch to return to main menu.
• To set time, refer to the user manual of the
host car audio.
Use map
Note
You may need to upgrade the map before
•
using it (see "Upgrade the map" section)
1
Touch the upper left corner to display home
menu.
2
Touch [Navigation] .
The navigation menu is displayed in a few
»
seconds.
3
Refer to the map manual (in Chinese) to
operate the navigation tool.
Tip
• You can press NAVI to enter/exit the
navigation system.

Load discs

4
You can play video, audio or images stored on the
following discs:
• DVD video, DVD-R, DVD-RW
• VCD
• Audio CD, CD-R, CD-RW