Related Manuals for iHealth Neo BP5S
Summary of Contents for iHealth Neo BP5S
- Page 1 Smart Blood Pressure Monitor Tensiomètre connecté Sfigmomanometro intelligente Tensiómetro inteligente Instruction For Use Notice d’utilisation Istruzioni per l'uso Instrucciones de uso...
- Page 2 Smart Blood Pressure Monitor...
-
Page 3: Package Contents
INTRODUCTION Thank you for selecting the iHealth Neo Smart Blood Pressure Monitor. The iHealth Neo Smart Blood Pressure Monitor is a fully automatic arm cuff blood pressure monitor that uses the oscillometric principle to measure your blood pressure and pulse rate. The monitor works with your mobile devices to track and share vital blood pressure data. -
Page 4: Parts And Display Indicators
Note: Consult your physician for proper interpretation of blood pressure results. CONTRAINDICATION It is not recommended for people with serious arrhythmia to use this Smart Blood Pressure Monitor. PARTS AND DISPLAY INDICATORS... -
Page 5: Setup Requirements
SET UP REQUIREMENTS Works with both iOS and Android devices: such as iPhone X/iPhone 8/Samsung Galaxy S6 Edge/SM-G9250/Samsung Galaxy Note3 Lite/Motorola Nexus 6 For a complete list of compatible devices, visit our support on page on www.ihealthlabs.eu... -
Page 6: Setup Procedures
SET UP PROCEDURES Download the Free iHealth MyVitals App Prior to first use, download and install “iHealth MyVitals” from the App Store or Google Play Store. Follow the on-screen instructions to register and set up your personal account. Access the iHealth Cloud Account Your iHealth account also gives you access to the free and secure iHealth cloud service. -
Page 7: Measurement Procedures
c. The monitor cannot take measurements or view measurement history until activate. To active the monitor, press START or M button on the monitor, the monitor shows “000” and Bluetooth indicator flashing. d. Place the monitor near your smartphone, and follow the steps of the App to complete connecting. - Page 8 c. The cuff should be placed at the same level as your heart. Note: Blood pressure can be affected by the position of the cuff and your physiologic condition. Apply the cuff a. Pull the cuff end through the metal loop, positioning it outward (away from your body). b.
-
Page 9: Taking Your Blood Pressure Reading
4. Stay still and calm for one to one and half minutes before taking a blood pressure measurement. Prolonged over-inflation of the bladder may cause ecchymoma of your arm. 5. Keep the cuff clean. Cleaning the cuff after every 200 times of usage is recommended. If the cuff becomes dirty, clean it with a moistened cloth. -
Page 10: Bluetooth Function
Connect to iOS/Android Device via Bluetooth a. Enable Bluetooth on your device. b. Launch the iHealth MyVitals App from your device. c. When a successful connection has been established, the Bluetooth indicator light will light up. d. When sync is processing, the sync indicator will flash, when sync is finished, The sync indicator lights up for 2 seconds and then light off. -
Page 11: Memory Function
If the monitor has no memory, Press the M button, the device display “000” at both systolic and diastolic. SPECIFICATIONS 1. Product name: iHealth Neo Smart Blood Pressure Monitor 2. Model: BP5S 3. Classification: Internally powered; Type BF applied part; IP22, No AP or APG; Continuous operation 4. -
Page 12: General Safety And Precautions
5. If an Irregular Heartbeat (IHB) is detected during the measurement procedure, the IHB symbol will be displayed in the “iHealth MyVitals” APP. Under this condition, the Smart Blood Pressure Monitor can keep functioning, but the results may be inaccurate. Please consult your physician for accurate assessment. - Page 13 1) The coefficient of variation (CV) of pulse period >25%. 2) The difference of adjacent pulse period is ≥0.14s and more than 53 percent of the total number of pulses readings falls within this definition. 6. Please do not use any cuff other than that supplied by the manufacturer as this may result in inaccurate measurements.
-
Page 14: Battery Handling And Usage
The battery charge will be displayed on the LED screen after each measurement. And when the monitor is connected to the “iHealth MyVitals” APP, the battery charge will be displayed in the APP. If the power is less than 25%, please charge the battery. -
Page 15: Troubleshooting
The monitor, cable, battery and cuff must be disposed of according to local regulations at the end of their usage. Note: The battery has limited charge cycles and may eventually need to be replaced by an iHealth service provider. Battery life and charge cycles vary by use and settings. - Page 16 Reset monitor by pressing the START button and holding for about 10 seconds, then connect the mobile device correctly and try again, If the monitor is still abnormal, please contact the local distributor or the factory.
-
Page 17: Care And Maintenance
CARE AND MAINTENANCE 1. If this monitor is stored near freezing temperatures, allow it to return to room temperature before use. 2. If the monitor is not used for a long time, please be sure to fully charge it every month. 3. -
Page 18: Warranty Information
Limited Warranty, if a defect arises and a valid claim is received by iHealth within the Warranty Period regarding the Product, at its option and to the extent permitted by law, iHealth will either (1) repair the Product using new or refurbished replacement parts or (2) exchange the Product with a new or refurbished Product. -
Page 19: Explanation Of Symbols
(d) to damage caused by operating the iHealth product outside the user manual, the technical specifications or other iHealth product published guidelines; (e) to damage caused by service performed by anyone who is not a representative of iHealth or one of its representatives. - Page 20 (1) This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. (2) Changes or modifications not expressly approved by iHealth Lab Inc. would void the user’s authority to operate the product.
-
Page 21: Other Standards And Compliances
the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This product complies with Industry Canada. -
Page 22: Electromagnetic Compatibility Information
–Part 2-30: Particular requirements for the basic safety and essential performance of automated non-invasive sphygmomanometers); EN 1060-1: 1995 + A2: 2009 (Non-invasive sphygmomanometers - Part 1: General requirements),; EN 1060-3: 1997 + A2: 2009 (Non-invasive sphygmomanometers - Part 3: Supplementary requirements for electro-mechanical blood pressure measuring systems);... - Page 23 Table 3 – Proximity fields from RF wireless communications equipment...
- Page 24 Table 4 – Input a.c. power Port...