Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are
!
adhered to when using this bench.
Locate bench in a suitable working area.
"
Keep the work area clean, uncluttered and ensure there is adequate lighting.
"
WARNING! Use bench on level and solid ground, preferably concrete. Avoid
!
tarmacadam since the bench may sink into the surface.
Keep the bench clean and tidy in accordance with good workshop practice.
"
Keep children and unauthorised persons away from the working area.
"
DO NOT use the bench for any purpose other than that for which it is designed.
#
DO NOT exceed maximum capacity of workbench.
#
DO NOT undertake work on the bench without the workpiece being adequately
#
secured. Use clamps or a vice (not included) to secure the workpiece. Available from
your Sealey dealer.
DO NOT use the bench out of doors.
#
DO NOT get the bench wet or use in damp or wet locations or areas where there is
#
condensation.
DO NOT clean the bench with any solvents which may damage the paint surface or the
#
protective coating on the wooden top.
The maximum load for each drawer is 25kg, full load for the workbench is 250kg.
!
2.
CONTENTS AND SPECIFICATION
2.1
Powder coated steel panels with 40mm wood laminate top. Five drawers. Open shelving for storage of larger items. Supplied flat
packed.
2.2
Table Size (W x D): 1372 x 508mm
Working Height: 865mm
Capacity: 250kg
2.3
Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.
A . . . .SIDE PANEL
C . . . .BOTTOM RAIL
D . . . .TOP RAIL
E . . . .CENTRE SUPPORT
G . . . .LEFT SIDE PANEL
H . . . .RIGHT SIDE PANEL
I . . . . .SUPPORT PANEL
J . . . . .BACK PANEL
K . . . .SHELF
INSTRUCTIONS FOR:
HEAVY-DUTY WORKBENCH WITH 5 DRAWERS
BALL BEARING RUNNERS
AP2030BB
:
MODEL
M . . . . .DRAWER
O . . . . .CORNER BRACE
P . . . . .WOODEN TOP
Q. . . . .LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8"
R . . . . .RIGHT SlDE RUNNER
S . . . . .SCREW (M5x12)
T . . . . .ADJUSTABLE LEG LEVELLER
AP2030BB - 1 - 260407
Advertisement
Related Manuals for Sealey AP2030BB
Summary of Contents for Sealey AP2030BB
- Page 1 AP2030BB MODEL Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 STEP 2. Attach the outer slide to the corresponding left/right side panel (G, H). Insert the tabs into the holes in the side panel making sure that the slider stop fits into the small hole. AP2030BB - 1 - 260407...
- Page 3 (I) to the side of the unit without sliders. Screw the top rails (D) onto the front and back. STEP 5. Secure the back panels (J) using 8 screws, 4 in each STEP 4. corner. AP2030BB - 1 - 260407...
- Page 4 STEP 8. Pull the middle slide and the ball bearings out as far as possible. Hold the drawer and slot the inner slide on the drawer into the middle slide, then push the drawer all the way in. take the shelves (K) and slot them into the support panels at the height required. To remove drawer see Step 2. AP2030BB - 1 - 260407...